AVAGO ACPL-332J Service Manual

ACPL-332J

SHIELD

SHIELD

D
R

I
V
E
R

V

E

DESAT

V

CC2

V

OUT

V

CLAMP

V

EE

V

CC1

V

S

FAULT

ANODE

CATHODE

V

CLAMP

V

LED

6, 7

5, 8

2

3

1, 4

13

11

14

9, 12

10

16

15

DESAT

UVLO

LED1

LED2

SHIELD

SHIELD

D
R

I
V
E
R

V

E

DESAT

V

CC2

V

OUT

V

CLAMP

V

EE

V

CC1

V

S

FAULT

ANODE

CATHODE

V

CLAMP

V

LED

6, 7

5, 8

2

3

1, 4

13

11

14

9, 12

10

16

15

DESAT

UVLO

LED1

LED2

Lead (Pb) Free

RoHS 6 fully
compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

2.5 Amp Output Current IGBT Gate Driver Optocoupler
with Integrated (VCE) Desaturation Detection, UVLO
Fault Status Feedback and Active Miller Clamping

Data Sheet

Description

The ACPL-332J is an advanced 2.5 A output current,
easy-to-use, intelligent gate driver which makes IGBT
VCE fault protection compact, aordable, and easy-to
implement. Features such as integrated VCE detection,
under voltage lockout (UVLO), “soft” IGBT turn-o, isolated
open collector fault feedback and active Miller clamping
provide maximum design exibility and circuit protec­tion.

The ACPL-332J contains a GaAsP LED. The LED is optically
coupled to an integrated circuit with a power output
stage. ACPL-332J is ideally suited for driving power IGBTs
and MOSFETs used in motor control inverter applications.
The voltage and current supplied by these optocouplers
make them ideally suited for directly driving IGBTs with
ratings up to 1200 V and 150 A. For IGBTs with higher
ratings, the ACPL-332J can be used to drive a discrete
power stage which drives the IGBT gate. The ACPL-332J
has an insulation voltage of V

Block Diagram

Features

• Under Voltage Lock-Out Protection (UVLO) with
Hysteresis

• Desaturation Detection

• Miller Clamping

• Open Collector Isolated fault feedback

• “Soft” IGBT Turn-o

• Fault Reset by next LED turn-on (low to high) after

fault mute period

• Available in SO-16 package

• Safety approvals: UL approved, 3750 V

CSA approved, IEC/EN/DIN-EN 60747-5-2 approved
V

= 891 V

IORM

PEAK

Specications

• 2.5 A maximum peak output current

= 891 V

IORM

CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.

PEAK

.

• 2.0 A minimum peak output current

• 250 ns maximum propagation delay over temperature

range

• 100 ns maximum pulse width distortion (PWD)

• 15 kV/µs minimum common mode rejection (CMR) at

VCM = 1500 V

• I

< 5 mA maximum supply current

CC(max)

• Wide VCC operating range: 15 V to 30 V over
temperature range

• 1.7 A Miller Clamp. Clamp pin short to VEE if not used

• Wide operating temperature range: –40°C to 100°C

Applications

• Isolated IGBT/Power MOSFET gate drive

• AC and brushless DC motor drives

• Industrial inverters and Uninterruptible Power Supply

(UPS)

for 1 minute,

RMS

Pin Description

1

2

3

4

5

6

7

8

16

15

14

13

12

11

10

9

V

E

V

LED

DESAT

V

CC2

V

EE

V

OUT

V

CLAMP

V

EE

V

S

V

CC1

FAULT

V

S

CATHODE

ANODE

ANODE

CATHODE

1

2

3

4

5

6

7

8

16

15

14

13

12

11

10

9

V

E

V

LED

DESAT

V

CC2

V

EE

V

OUT

V

CLAMP

V

EE

V

S

V

CC1

FAULT

V

S

CATHODE

ANODE

ANODE

CATHODE

Pin Symbol Description

1 V

2 V

S

CC1

3 FAULT Fault output. FAULT changes from a high impedance state

4 V

S

5 CATHODE Cathode

6 ANODE Anode

7 ANODE Anode

8 CATHODE Cathode

9 V

10 V

11 V

12 V

13 V

EE

CLAMP

OUT

EE

CC2

14 DESAT Desaturation voltage input. When the voltage on DESAT

15 V

16 V

LED

E

Input Ground

Positive input supply voltage. (4.5 V to 5.5 V)

to a logic low output within 5 µs of the voltage on the
DESAT pin exceeding an internal reference voltage of 7 V.
FAULT output is an open collector which allows the FAULT
outputs from all ACPL-332J in a circuit to be connected
together in a “wired OR” forming a single fault bus for inter­facing directly to the micro-controller.

Input Ground

Output supply voltage.

Miller clamp

Gate drive voltage output

Output supply voltage.

Positive output supply voltage

exceeds an internal reference voltage of 6.5 V while the
IGBT is on, FAULT output is changed from a high impedance
state to a logic low state within 5 µs.

LED anode. This pin must be left unconnected for guaran­teed data sheet performance. (For optical coupling testing
only)

Common (IGBT emitter) output supply voltage.

Ordering Information

ACPL-332J is UL Recognized with 3750 Vrms for 1 minute per UL1577.

Option

Part number

ACPL-332J -000E SO-16 X X 45 per tube

-500E

Package

To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.

Example 1:

ACPL-332J-500E to order product of SO-16 Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN

60747-5-2 Safety Approval in RoHS compliant.

Example 2:

ACPL-332J-000E to order product of SO-16 Surface Mount package in tube packaging with IEC/EN/DIN EN 60747-5-

2 Safety Approval and RoHS compliant.

Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.

Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.

Surface

Mount Tape& Reel

X X X

IEC/EN/DIN EN

60747-5-2 QuantityRoHS Compliant

850 per reel

2

Package Outline Drawings

9

0.295 ± 0.010

(7.493 ± 0.254)

10111213141516

87654321

0.018

(0.457)

0.138 ± 0.005

(3.505 ± 0.127)

9°

0.406 ± 0.10

(10.312 ± 0.254)

0.408 ± 0.010

(10.363 ± 0.254)

0.025 MIN.

0.008 ± 0.003

(0.203 ± 0.076)

STANDOFF

0.345 ± 0.010

(8.763 ± 0.254)

0- 8 °

0.018

(0.457)

0.050

(1.270)

ALL LEADS
TO BE
COPLANAR
± 0.002

A 332J
YYWW

TYPE NUMBER
DATE CODE

0.458 (11.63)

0.085 (2.16)

0.025 (0.64)

LAND PATTERN RECOMMENDATION

ACPL-332J 16-Lead Surface Mount Package

Dimensions in inches (millimeters)
Notes: Initial and continued variation in the color of the ACPL-332J’s white mold compound is normal and does note aect device performance or
reliability.
Floating Lead Protrusion is 0.25 mm (10 mils) max.

3

Solder Reow Thermal Prole

0

TIME (SECONDS)

TEMPERATURE ( °C)

200

100

50 150100 200 250

300

0

30

SEC.

50 SEC.

30

SEC.

160 °C

140 °C

150 °C

PEAK

TEMP.

245°C

PEAK
TEMP.
240 °C

PEAK

TEMP.

230 °C

SOLDERING

TIME

200 °C

PREHEATING TIME
150 °C, 90 + 30 SEC.

2.5 °C ± 0.5 °C/SEC.

3°C + 1 °C/ - 0.5 °C

TIGHT
TYPICAL
LOOSE

ROOM

TEMPERATURE

PREHEATING RATE 3 °C + 1 °C/ - 0.5 ° C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.

217 °C

RAMP-DOWN
6 °C/SEC. MAX.

RAMP-UP

3 °C/SEC. MAX.

150 - 200 °C

260 +0/-5 °C

t 25 °C to PEAK

60 to 150 SEC.

20-40 SEC.

TIME WITHIN 5°C of ACTUAL
PEAK TEMPERATURE

t

p

t

s

PREHEAT

60 to 180 SEC.

t

L

T

L

T

smax

T

smin

25

T

p

TIME

TEMPERATURE

NO TES:
THE TIME FROM 25°C to PEAK TEMPERATURE = 8 MINUTES MAX.
T

smax

= 200 °C, T

smin

= 150 °C

Note: Non-halide ux should be used.

Recommended Pb-Free IR Prole

Note: Non-halide ux should be used.

4

Regulatory Information

The ACPL-332J is approved by the following organizations:

IEC/EN/DIN EN 60747-5-2

Approval under:
IEC 60747-5-2 :1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01

UL

Approval under UL 1577, component recognition
program up to V

= 3750 V

ISO

. File E55361.

RMS

CSA

Approval under CSA Component Acceptance Notice #5,
File CA 88324.

Table 1. IEC/EN/DIN EN 60747-5-2 Insulation Characteristics*

Description Symbol Characteristic Unit

Installation classication per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150 V
for rated mains voltage ≤ 300 V
for rated mains voltage ≤ 600 V

rms

rms

rms

Climatic Classication 55/100/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage V

Input to Output Test Voltage, Method b**,
V

x 1.875=VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC

IORM

Input to Output Test Voltage, Method a**,
V

x 1.5=VPR, Type and Sample Test, tm=60 sec, Partial discharge < 5 pC

IORM

Highest Allowable Overvoltage (Transient Overvoltage t

= 10 sec) V

ini

V

V

IORM

PR

PR

IOTM

Safety-limiting values – maximum values allowed in the event of a failure.

Case Temperature T

Input Current I

Output Power P

Insulation Resistance at TS, VIO = 500 V R

S

S, INPUT

S, OUTPUT

S

I – IV
I – IV
I – III

891 V

1670 V

1336 V

6000 V

175

400 mA

1200 mW

9

>10

peak

peak

peak

peak

°C

W

* Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

Surface mount classication is class A in accordance with CECCOO802.

** Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section IEC/EN/

DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test proles.

Dependence of Safety Limiting Values on Temperature. (take from DS AV01-0579EN Pg.7)

5

Table 2. Insulation and Safety Related Specications

Parameter Symbol ACPL-332J Units Conditions

Minimum External Air Gap
(Clearance)

Minimum External Tracking
(Creepage)

Minimum Internal Plastic Gap
(Internal Clearance)

Tracking Resistance
(Comparative Tracking Index)

Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)

L(101) 8.3 Mm Measured from input terminals to output terminals,

shortest distance through air.

L(102) 8.3 Mm Measured from input terminals to output terminals,

shortest distance path along body.

0.5 Mm Through insulation distance conductor to conductor,
usually the straight line distance thickness between
the emitter and detector.

CTI >175 V DIN IEC 112/VDE 0303 Part 1

Table 3. Absolute Maximum Ratings

Parameter Symbol Min. Max. Units Note

Storage Temperature T

Operating Temperature T

Output IC Junction Temperature T

Average Input Current I

Peak Transient Input Current,

S

A

J

F(AVG)

I

F(TRAN)

(<1 µs pulse width, 300pps)

Reverse Input Voltage V

“High” Peak Output Current I

“Low” Peak Output Current I

Positive Input Supply Voltage V

FAULT Output Current I

FAULT Pin Voltage V

Total Output Supply Voltage (V

R

OH(PEAK)

OL(PEAK)

CC1

FAULT

FAULT

- VEE) -0.5 33 V

CC2

Negative Output Supply Voltage (VE - VEE) -0.5 15 V 6

Positive Output Supply Voltage (V

Gate Drive Output Voltage V

Peak Clamping Sinking Current I

Miller Clamping Pin Voltage V

DESAT Voltage V

Output IC Power Dissipation P

Input IC Power Dissipation P

- VE) -0.5 33 - (VE - VEE) V

CC2

O(PEAK)

Clamp

Clamp

DESAT

O

I

Solder Reow Temperature Prole See Package Outline Drawings section

-55 125 °C

-40 100 °C 2

125 °C 2

25 mA 1

1.0 A

5 V

2.5 A 3

2.5 A 3

-0.5 5.5 V

8.0 mA

-0.5 V

-0.5 V

CC1

CC2

V

V

1.7 A

-0.5 V

V

E

CC2

VE + 10 V

V

600 mW 2

150 mW 2

Table 4. Recommended Operating Conditions

Parameter Symbol Min. Max. Units Note

Operating Temperature T

Total Output Supply Voltage (V

A

- VEE) 15 30 V 7

CC2

Negative Output Supply Voltage (VE - VEE) 0 15 V 4

Positive Output Supply Voltage (V

Input Current (ON) I

Input Voltage (OFF) V

- VE) 15 30 - (VE - VEE) V

CC2

F(ON)

F(OFF)

6

- 40 100 °C 2

8 12 mA

- 3.6 0.8 V

Table 5. Electrical Specications (DC)

Unless otherwise noted, all typical values at TA = 25°C, V

- VEE = 30 V, VE - VEE = 0 V;

CC2

all Minimum/Maximum specications are at Recommended Operating Conditions. Positive Supply Voltage used.

Parameter Symbol Min. Typ. Max. Units Test Conditions Fig. Note

FAULT Logic Low Output
Voltage

FAULT Logic High Output
Current

High Level
Output Current

Low Level
Output Current

Low Level Output Current
During Fault Condition

High Level Output Voltage V

Low Level Output Voltage V

Clamp Pin Threshold Voltage V

Clamp Low Level
Sinking Current

High Level Supply Current I

Low Level Supply Current I

Blanking Capacitor
Charging Current

Blanking Capacitor
Discharge Current

DESAT Threshold V

UVLO Threshold V

UVLO Hysteresis (V

Threshold Input Current
Low to High

Threshold Input Voltage
High to Low

Input Forward Voltage V

Temperature Coecient
of Input Forward Voltage

Input Reverse Breakdown
Voltage

Input Capacitance C

V

FAULTL

I

FAULTH

I

OH

I

OL

I

OLF

OH

OL

tClamp

I

CL

CC2H

CC2L

I

CHG

I

DSCHG

DESAT

UVLO+

V

UVLO-

UVLO+

- V

UVLO-

I

FLH

V

FHL

F

DVF/DT

BV

R

IN

0.1 V I

0.1 V I

0.003 µA V

0.003 µA V

-0.5 -1.5 A VO = V

-2.0 A VO = V

FAULT

FAULT

FAULT

FAULT

= 1.1 mA, V

= 1.1 mA, V

= 5.5 V, V

= 3.3 V, V

- 4 2, 4, 215

CC2

– 15 3

CC2

CC1

CC1

CC1

CC1

= 5.5V

= 3.3V

= 5.5V

= 3.3V

0.5 1.5 A VO = VEE + 2.5 3, 5, 225

2.0 A VO = VEE + 15 3

90 140 230 mA V

- VEE = 14 V 6

OUT

VCC-3.5 VCC-2.5 V IO = 100 mA 4, 6, 237, 8, 9

VCC-2.9 VCC-2.0 V IO = -650 µA 23

0.17 0.5 V IO = 100 mA 5, 7,
24

2.0 V

0.35 1.1 A VO = VEE + 2.5 8

2.5 5 mA IO = 0 mA 9, 10,

2.5 5 mA IO = 0 mA

-0.13 -0.24 -0.33 mA V

10 30 mA V

6 6.5 7.5 V V

= 2 V 11, 27 9, 10

DESAT

= 7.0 V 28

DESAT

-VE >V

CC2

UVLO-

25,
26

12 9

10.5 11.6 12.5 V VO > 5 V 7, 9,

9.2 10.3 11.1 V VO < 5 V 7, 9,

0.4 1.3 V

)

2.0 8 mA IO = 0 mA, VO > 5 V

0.8 V

1.2 1.6 1.95 V IF = 10 mA

A

5 V

-1.3 mV/°C

IR = 10 mA

70 pF f = 1 MHz, VF = 0 V

9

11

12

7

Table 6. Switching Specications (AC)

Unless otherwise noted, all typical values at TA = 25°C, V

- VEE = 30 V, VE - VEE = 0 V;

CC2

all Minimum/Maximum specications are at Recommended Operating Conditions. Only Positive Supply Voltage used.

Parameter Symbol Min. Typ. Max. Units Test Conditions Fig. Note

Propagation Delay Time
to High Output Level

Propagation Delay Time
to Low Output Level

Pulse Width Distortion PWD -100 20 100 ns 14, 17

Propagation Delay
Dierence Between
Any Two Parts or Channels

Rise Time t

Fall Time t

DESAT Sense to
90%VO Delay

DESAT Sense to
10% VO Delay

DESAT Sense to Low Level
FAULT Signal Delay

DESAT Sense to DESAT
Low Propagation Delay

DESAT Input Mute t

RESET to High Level FAULT
Signal Delay

Output High Level Common
Mode Transient Immunity

Output Low Level Common
Mode Transient Immunity

t

PLH

100 180 250 ns

Rg = 10 W,
Cg = 10 nF,
f = 10 kHz,

t

(t

PHL

PHL

- t

100 180 250 ns 1, 13,

)

-350 350 ns 17, 16

PLH

Duty Cycle = 50%,
IF = 10 mA,
V

= 30 V

CC2

PDD

R

F

t

DESAT(90%)

t

DESAT(10%)

t

DESAT(FAULT)

50 ns

50 ns

0.15 0.5 µs

2 3 µs

0.25 0.5 µs

C

= 100pF, Rg = 10 W,

DESAT

Cg = 10 nF, V

C

DESAT

Cg = 10 nF, V

C

DESAT

CC2

= 100pF, Rg = 10 W,

CC2

= 100pF, RF = 2.1 kW,

= 30 V

= 30 V

Rg = 10 W, Cg = 10 nF,
V

= 30 V

CC2

t

DESAT(LOW)

0.25 µs

C

= 100pF, RF = 2.1 kW,

DESAT

Rg = 10 W, Cg = 10 nF,
V

= 30 V

CC2

DESAT(MUTE)

t

RESET(FAULT )

5 µs 37 20

0.3 1 2.0 µs

C

= 100pF, RF = 2.1 kW,

DESAT

Rg = 10 W, Cg = 10 nF,
V

0.8 1.5 2.5 µs

= 5.5V, V

CC1

C

= 100pF, RF = 2.1 kW,

DESAT

CC2

= 30 V

Rg = 10 W, Cg = 10 nF,
V

= 3.3V, V

CC1

CC2

= 30 V

|CMH| 15 25 kV/µs TA = 25°C, IF = 10 mA

VCM = 1500 V, V

CC2

= 30 V

|CML| 15 25 kV/µs TA = 25°C, VF = 0 V

VCM = 1500 V, V

CC2

= 30 V

1, 13,

13, 15
14, 15,
16, 29

14, 15,
16, 29

17, 30, 3719

18, 19,
20, 30,
37

30, 37 18

30, 37 19

31, 32,

21
33, 34

31, 32,

22
33, 34

8