KEYLESS ENTRY AND ALARM SYSTEM
ASL-550
User Guide
Table of Contents
Introduction .......................................................1
One-Way Transmitter Functionalities............. 2
Transmitter Operation ................................... 2
Two-Way Transmitter Functionalities............. 3
F button Functionality: ................................... 3
Backlight: .......................................................3
Selecting and adjusting Menu options: .........4
Parking Countdown ....................................... 5
Alarm Clock ................................................... 5
Valet menu..................................................... 5
Secure Remote feature ................................. 6
Clock Menu.................................................... 6
F Button Function Menu ................................ 6
Button Operation ........................................... 6
Features Available on your System................ 7
Relock doors.................................................. 7
Panic Mode.................................................... 7
Multi-car Operation ........................................7
Temporary Chirp Delete ................................8
Priority Door Access ......................................8
Alarm Functions............................................. 8
Intrusion Code Warning Function ....Error!
Bookmark not defined.
Passive Arm Mode................................... 9
Active Arm Mode...................................... 9
Disarming and Unlocking Doors.................. 10
Starter Disable............................................. 10
To Arm the Starter Disable .................... 10
To Disarm the Starter Disable ............... 10
Retain Accessory Output............................. 10
System L.E.D. Flash Rate ...........................10
Valet Operation............................................ 11
Enabling the Alarm Valet ....................... 11
Disabling the Alarm Valet....................... 11
Remote Valet Operation .............................. 11
Parking Lights Flash Rate .............................. 12
Introduction
Congratulations on the purchase of your new alarm system by Autostart! Whether you have
chosen a 1-way system or a 2-Way system, you can now have the peace of mind of knowing that
your prized possession is now protected by a sophisticated, state-of-the-art alarm system. Packed
with many advanced features, this system will satisfy any one of your expectations of high-end
commodity and security, without neglecting any standard feature commonly offered by entry-level
systems. Please read carefully this user guide to get acquainted with the operation and the
features of your alarm system. Some features require extra parts and installation labour; please
contact your installation centre for more details.
INDUSTRY CANADA USER NOTICE:
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
DOC: 1.00
- ASL-550TW-FM - - August 29, 2007 - - MO - Assembled in Canada
One-Way Transmitter Functionalities
p
p
A
AUX
LOCK Button
Lock doors and arms,
or activates Panic Mode
if
ressed for 4 sec.
TRUNK Button
Activates the
trunk release and
silent arming.
Picture serves as example only.
Transmitter Operation
BUTTON(S) to press FUNCTION
or
(while siren sounding)
• Locks doors.
• Arms Starter Kill (not in Alarm Valet).
• Dome light OFF (If programmed).
• Unlocks driver’s door.
• Disarms Starter Kill (not in Valet) – rearm timer at 60 sec.
• Dome light ON for 60 sec. or until Ignition goes ON or LOCK is pressed (If
programmed).
• Mutes siren; system not disarmed. A second UNLOCK press is required to
disarm, unless the passive arming mode with SINGLE-STAGE disarm is
selected.
UX Button
Allows access to Multilevel
functions
UNLOCK Button
(Unlocks doors and disarms,
or activates Panic Mode if
ressed for 4 sec.
2 Button
AUX 2 and Car Finder
(2 times)
• Unlocks all doors (If Priority Door programmed).
• AUX 2 - 1 flash and 1 chirp (If Car Finder was enabled).
(for 4 seconds)
(for 4 seconds)
(for 3 seconds)
+
• Mutes siren — system not disarmed.
• Locks doors.
• Enters Panic Mode – siren ON for 60 sec., exits Valet Mode if Panic is
triggered.
• Unlocks doors.
• Enters Panic Mode – siren ON for 60 sec., exits Valet Mode if Panic is
triggered.
• AUX 3 output with 1-sec. pulse (Trunk Mode) or toggle ON / OFF (in Latch
Mode).
• Mutes siren — system will disarm if Trunk is pressed.
• Valet ON or Valet OFF.
(for 3 seconds)
P. 2 User Guide
A
A
A
Function Button:
. Turns ON the backlight
. Allows access to Multi-
level functions
LOCK Button:
. Locks all Doors and
arms the Starter Kill
UNLOCK Button:
. Unlocks all Doors and
disarms the Starter Kill
Two-Way Transmitter Functionalities
UX 2 Button:
. Activates the AUX 2 output and
Car Finder (if enabled)
uxiliary Button
. Selects option 5 while in
programming mode (if
configured)
. Saves settings while in
Siren/Horn Adjustment Mode if
button is configured to AUX 2
ctivates Panic Mode if
.
TRUNK Button:
. Activates the Trunk and
disarms the alarm
F button Functionality:
(By default)
Note: The order of LEVELS and MENU can be re-arranged in the menu option FBPRO.
button
1x Level 1 L – 01 Enable backlight
2x Level 2 L – 02 Enable backlight
3x Level 3 L – 03 Enable backlight
4x Enters programming mode MENU Enable backlight
Press
less than 3 seconds
LCD display Press
less than 1 second
Backlight:
Press and hold the button (for more than 3 seconds and less than 5 seconds), to turn the
Backlight ON for 3 seconds. If the button is pressed down for more than 5 seconds, the
backlight will stay
press the
ON until the button is released. A quick way to access the backlight is to
button quickly (for less than 1 second); the backlight will turn on until the MENU
operation ends.
User Guide P. 3
Button
Press for < 1 second Backlight ON until MENU operation ends.
Press for > 3 seconds and < 5 seconds Backlight ON for 3 seconds.
Press for > 5 seconds
Backlight will stay ON until button
Backlight
is released.
Selecting and adjusting Menu options:
When in MENU, press button to enter the menu.
Press butt button to move up in the menu or buttbutton to move down in the menu.
Press button to select the option you would like to adjust.
Press button to increase the value or to activate or deactivate a function or toggle through
the selection.
Press button to decrease the value or to activate or deactivate a function or toggle
through the selection.
Press
button to move to the next sub-option or go back to the main menu.
Order Menu Option LCD display Function
1 Parking Menu PARK
Parking hour P 0:00
Parking minute P 0:30
Toggle Parking
countdown
2 F Button Function
Menu
FB Programming 1 2 3 M
3 Illumination Menu ILLUM
Toggle Illumination
Mode
4 Keypad Lock Time
Menu
Keypad lock time 05
5 Side Button
Program Menu
Side Button
Programming
6 Language Menu LANGU
Language ENG
0 is flashing
30 is flashing
P – ON +
Or
P – OFF
FBPRO F Button Programming
2 3 1 M
2 1 3 M
3 1 2 M
M 1 2 3
ON
Or
OFF
KELOC
10
20
SBPRO AUX Button Programming
PANIC
AUX
Or
FRAN
There is a beep 5 min. before the Parking countdown
ON – basic operation with backlight illumination.
OFF – basic operation without backlight illumination.
When the SECURE is ON, Keypad will be locked
automatically 5 sec./10 sec./20 sec. after the MENU
When PANIC is chosen, pressing button activates
AUX only used to select option 5 in programming mode.
Adjusts parking hour
(value from 0 to 2).
Adjusts parking minute
(value from 0 to 59).
Enables or disables parking countdown.
reaches 0.
operation ends.
PANIC Mode.
English is default.
P. 4 User Guide
7 Clock Menu CLOCK
Clock hour 12:00
Clock minute 12:00
8 Confirmation
Mode Menu
Confirmation Mode BZVIB
Toggle BZVIB BUZ
Toggle BLITE ON
9 Backlight Color
Menu
Backlight There are 8
10 SECURE Menu SECUR Locks the transmitter’s keypad.
Toggle lock remote ON
11 VALET Menu VALET
Toggle Valet Mode ON
12 Alarm Clock Menu ALARM
Alarm hour A 12:00
Alarm minute A 12:00
Toggle alarm A – ON +
12 is flashing
00 is flashing
CONFM
Or
BLITE
Or
VIB + vib ICON
Or
OFF
COLOR
different colors.
C1-C8
Or
OFF
Or
OFF
12 is flashing
00 is flashing
Or
A – OFF
OFF – unlocks the transmitter’s keypad.
Adjusts clock hour
(value from 0 to 12).
Adjusts clock minute
(value from 0 to 59).
Buzzer and Vibration option
Red Backlight option for Alarm
Buzzer
Vibration
Red backlight flashing when alarm
No red backlight flashing when alarm
Blue light is default C1-C8 color.
ON – locks the transmitter’s keypad.
Adjusts alarm hour
(value from 0 to 12).
Adjusts alarm minute
(value from 0 to 59).
Enables or disables alarm.
Parking Countdown
This version of the countdown feature is particularly useful for keeping track of parking meter time:
The user may quickly set up the countdown using the
5 minutes before the Parking Countdown reaches 0.
Parking Menu. The transmitter will beep once,
Alarm Clock
The LCD remote control has a built-in alarm clock, which can be set up using the Alarm Clock
Menu. Once the programmed time is reached, the remote will beep 6 times every minute until a
button is pressed.
Valet menu
When this feature is enabled, press for 3 sec. to enter Valet Mode. When this feature is
disabled, press + buttons simultaneously.
User Guide P. 5
Secure Remote feature
This feature is used to lock the keypad of the transmitter to avoid accidental button press. When
the remote is locked and a button (except F button) is pressed, the LCD will display “
PRESF” for 1
second and go back to the clock.
The transmitter keypad can also be locked as follows:
• Press to go to Menu
• Within 3 seconds, press
Press
display “
for about 1 sec. to unlock the transmitter keypad. At the same time, the LCD screen will
PRESb” for 1 sec. and then go back to the clock.
Clock Menu
The Clock menu is used to set the current time on your remote control.
F Button Function Menu
The order of LEVELS and MENU can be re-arranged using the F Button Function Menu.
Button Operation
Button LCD Sounder
Lock button
Unlock button
Trunk button TRUNK text + trunk lid up for 3 sec. 1 beep
AUX 2 button 1 beep
Auxiliary Button PANIC - transmits PANIC Mode code
Unlock+Start button Valet icon if pressed more than 3 sec. 1 beep
AUX - transmits AUX code
Lock+Unlock button Same as AUX button -
Trunk+Lock button
(2nd car operation)
Trunk+Unlock button
(2nd car operation)
L --01 → Lock button
L --01 → Unlock button
L --01 → Trunk button
L --02 → Lock button
nd
car unlock)
(2
L --02 → Unlock button (2nd
car unlock)
L --02 → Trunk button(2nd car
TRUNK text + trunk lid up for 3 sec. 1 beep
trunk)
L --03 → Lock button
(Channel 1)
L --03 → Unlock button
(Channel 2)
L --03 → Trunk button
(Channel 3)
L --03 → Start button
(Channel 4)
+ LOCK
+ UNLOCK
+ LOCK
+ UNLOCK
LOCK +
UNLOCK +
1 beep
1 beep
1 beep
1 beep
1 beep
2 beeps
1 beep
2 beeps
1 beep
2 beeps
P. 6 User Guide
Features Available on your System
Relock doors
If you unlock the doors with the remote transmitter, but do not open any door or the trunk within 30
seconds, the doors will automatically relock and the system will be armed.
Note: When the system is in active arming mode and the relock mode is enabled, the doors will
relock but the system will not rearm.
Panic Mode
In a panic situation, sounds the siren for 1 minute.
To activate Panic Mode:
• Press and hold the UNLOCK button for approximately 3 sec. until the sound signal starts
and the parking lights flash: this will unlock the doors before the sound signal starts.
• Press and hold the LOCK button for approximately 3 seconds until the sound signal
starts and the parking lights flash: this will lock the doors before the sound signal starts.
Or
• Press and hold auxiliary button for 3 sec. until the sound signal starts and the parking
lights flash. Note: This will only work if auxiliary button is configured as Panic.
Multi-car Operation
The system features multi-car operation. This allows the user to control two systems with one
transmitter. (Both vehicles must be equipped with identical systems). The transmitter of the primary
vehicle can control the Starter Kill system, the door lock and unlock operations of the second
vehicle as well as the AUX 2 and AUX 3 outputs. The transmitter of the second vehicle can also
operate the primary vehicle.
For 1-WAY remote:
• + ..................................................Lock
• + ...................................... Unlock
• + . ......................................... Aux 2
• + + .............................. Aux 3
Or
• Î Î ………………..Lock
• Î Î ...............................Unlock
• Î Î …………………Aux 2
• Î Î ………………….Aux 3
User Guide P. 7
For 2-WAY LCD remote:
• Press and hold the
release the
hold the
displayed. This display means that you are now in Multi-car Operation Mode.
Simply press the corresponding button to access the desired feature:
• ......................................................................Lock
• ............................................................ Unlock
• . ....................................................... Aux 2
• . ...................................................... Aux 3
Or
• + simultaneously ...........................Lock
• + simultaneously .................... Unlock
• + simultaneously ................... Aux 2
FUNCTION button until you hear a “beep”. Within 3 seconds,
FUNCTION button and L-01 will appear on the LCD display. Press and
FUNCTION button once more until you hear another “beep”. L-02 will be
• ¾ ¾ …………………. Aux 3
Temporary Chirp Delete
If you want to avoid the siren chirps in a quiet neighbourhood when arming or disarming the
system, press the
within 3 seconds, press the
TRUNK button until you see the parking lights flash and hear 1 beep. Then
LOCK or UNLOCK to arm or disarm the vehicle without generating the
siren chirps.
Note: Your installer could program the chirp disable feature, so that the chirps are disabled permanently.
Priority Door Access
(Enabled by default.) If the Remote Door Locks option is installed on your vehicle, this safety
feature allows you to unlock solely the driver’s door with a single press of the
the transmitter. Upon a second press of the
driver’s door. With a third press of the
UNLOCK button, all the doors will unlock, except for the
UNLOCK button, all the doors will unlock.
UNLOCK button on
Alarm Functions
(The siren and the shock detectors are optional)
Your installer can program your alarm in passive arming mode, so that the system automatically
arms itself when you leave your vehicle, or in active arming mode, so that you can arm or disarm
your car at will.
In either mode, you can arm or disarm your alarm system using your remote control as well as lock
or unlock your doors.
When an intrusion from the door, hood, trunk, shock or ignition is detected, the 2-way LCD remote
will send beeps or vibrate for about 60 seconds. At the same time, the LCD remote will display
P. 8 User Guide
“ALARM”, “Time” (the moment the Alarm was triggered) and “DOOR/HOOD/TRUNK/SHOCK”
(depending on the type of alarm) alternately. The icons of door, hood, trunk and shock, as well as
the red backlight, will be flashing (when the
BLITE is set ON).
Alarm Type LCD Text Icon
DOOR ALARM + DOOR
HOOD ALARM + HOOD
TRUNK ALARM + TRUNK
Car front view outline +
door open and close
Car side view outline +
hood up and down
Car side view outline +
trunk lid up and down
Sound or
Vibration
60 seconds
60 seconds
60 seconds
SHOCK ALARM + SHOCK
IGNITION ALARM + real time NONE 60 seconds
Car front view outline +
lightning rods flashing
60 seconds
The user can press the LOCK or UNLOCK button to stop the alarm (unless DUAL-STAGE Mode has
been programmed – one press then only mutes the siren; the user needs to press twice in order to
disarm the system).
Passive Arm Mode
In passive arming mode, the system will arm itself automatically after the completion of a 1-min.
arming delay (LED flashes quickly), initiated after the last door of the vehicle is closed. Therefore,
you do not need to arm the system. The LED indicator flashes slowly when the system is armed.
However, you must lock your doors manually when leaving the vehicle.
When leaving your vehicle, perform the following:
1. Turn the key switch off. The LED remains off.
2. Unlock if required and open the doors.
3. Once all doors are closed after exiting the vehicle, the LED will begin to flash quickly,
indicating that passive arming delay has begun.
Also, as long as a door, trunk or hood is open before the completion of the arming delay, the
system will not rearm. If you want to stay in the vehicle for a certain period of time, it is
recommended to have your key switch in the
arms before somebody leaves the vehicle. While your key is in the
ON position to avoid a situation where the system
ON position, the system will not
arm and the LED will stay off.
For the two-way LCD remote, once the system is armed automatically, the “
LOCK” will be displayed
for 1 minute, and the icon will be on the LCD screen.
Active Arm Mode
To arm the system and lock your doors (if you have this option), the ignition must go from ON to
OFF and a door has to be opened and then closed. Press the LOCK button on your remote until the
siren chirps once in confirmation. Notice that the parking lights confirm the system arming by
flashing once and that the LED indicator flashes slowly to confirm the armed state, or that the
I icon is on the LCD screen (for the 2-way remote).
User Guide P. 9
Disarming and Unlocking Doors
If the system was programmed in passive mode, to disarm the system and unlock the doors, press
and hold the
UNLOCK button until the siren chirps twice in confirmation. Notice also that the parking
lights confirm the system disarming by flashing twice. Once the system is disarmed, you have to
open a door within a 35-second delay or else the system will rearm (LED flashing slowly). If the
entry delay expires, you must disarm the vehicle by pressing the
UNLOCK button to enter the
vehicle. Once inside the vehicle, you have up to 35 seconds to turn the key switch to the ON
position or start the car to prevent the system from rearming again. If this is not done, your system
will rearm (LED flashing slowly) and, if your system has a Starter Kill, you will not be able to start
the car. If this situation occurs, you need to disarm the car by pressing the
UNLOCK button.
Starter Disable
Among the many features, the starter disable circuit will immobilize the vehicle when the system is
armed (If installed). The system, when armed, will control a relay that will physically interrupt the
vehicle starter wire and prevent the starting of your vehicle. The system is selectable, passive or
active arming; this means that you can have the unit arm itself (passive) after a pre-programmed
period of time, or you can have control over the system (active) such that it will never arm itself.
Note: When the system is armed, the vehicle will not start with the key unless the system has
been disarmed.
To Arm the Starter Disable
• Lock the doors by remote or wait the time-out period in passive arm mode. The system is armed
automatically when the doors are locked by remote.
To Disarm the Starter Disable
• Unlock the doors by remote or place the unit into Valet Mode.
Retain Accessory Output
Retain Accessory output is activated as soon as the key is turned to the ON position. When the key
goes from
minutes is set. The output is turned
ON to OFF position, the accessory output stays ON and a countdown period of 10
OFF after 10 minutes or if a door is opened anytime during the
countdown period.
Note: The Accessory Output is also turned off while starting the car.
System L.E.D. Flash Rate
The L.E.D will display the status of the system, to indicate if the starter kill is armed or disarmed.
The L.E.D will also indicate if the system is in Valet Mode or not.
The following are L.E.D conditions:
L.E.D State System Status Mode
OFF Starter kill Disarmed Regular operation
ON Solid Starter kill Disarmed Valet Mode
Flashing slowly Starter Kill armed Regular operation
Flashing quickly System is in rearming sequence Passive arming Mode
P. 10 User Guide
Valet Operation
The unit can be placed into Alarm Valet Mode to stop alarm conditions or to disable the alarm
functions and the anti-theft Starter Kill feature. While a vehicle stands in Alarm Valet Mode, Panic
mode and door locking/unlocking functions are still operational.
Enabling the Alarm Valet
1. Turn the key to the RUN position.
2. Within 5 sec. press and hold the Valet button for about 3 seconds.
3. The parking lights will flash 3 times to indicate that the system has entered Valet Mode.
4. Release the Valet button and turn the key to
OFF position
5. The LED will come on and stays lit to indicate that the Alarm Valet Mode is enabled. For
the 2-way LCD remote, the icon will be displayed on the LCD.
Disabling the Alarm Valet
1. Turn the ignition to the RUN position.
2. Within 5 sec. press and hold the Valet button for about 3 seconds.
3. The parking lights will flash twice to indicate that the system is out of Valet Mode.
4. Release the Valet button and turn the key to OFF position
5. The LED will go out to indicate that the Alarm Valet is disabled. For the 2-way remote,
the icon will disappear from the LCD.
Remote Valet Operation
The system can be placed in or out of Valet Mode through the remote control. This means that the
user does not have to enter the vehicle or switch the key to the
Valet Mode.
To place the system in or out of Valet Mode:
RUN position to get in or out of
• Press and hold + buttons simultaneously for 3 seconds on the transmitter; the
system will toggle in and out of Valet Mode:
o Getting into Valet Mode, the parking lights will flash 3 times, the LED will
come on and remain lit. For the 2-way LCD remote, the icon will be
displayed on the LCD.
o Getting out of Valet Mode, the parking lights will flash twice, the LED will go
out. For the 2-way LCD remote, the icon will disappear from the LCD.
Or
• To get into Valet Mode, press the button to go to the MENU.
• Press to go to the next stage MENU; press or to go to the VALET MENU.
• Press
(COMBO VALET) Mode.
to go to the next stage MENU; press or to choose the CMVLT
• Press to go to the next stage MENU; press or to choose the ON.
• Press and hold
• The parking lights will flash 3 times and the LED on the antenna will remain
for 5 seconds.
ON solid.
• The icon will appear on your LCD remote.
• To get out of Valet mode, press the
• Press to go to the next stage
• Press to go to the next stage
VALET) Mode.
• Press
to go to the next stage MENU; press or to choose the ON.
button to go to the MENU.
MENU; press or to go to the VALET MENU.
MENU; press or to choose the CMVLT (COMBO
User Guide P. 11
• Press and hold for 5 seconds.
• The parking lights will flash 2 times and the LED on the antenna will turn
• The icon will disappear on your LCD remote.
Parking Lights Flash Rate
FLASHES &
CHIRPS
1 Quick Locked by transmitter, system armed, Starter Kill armed.
1 Quick Car Finder.
2 Quick
3 Quick
4 Quick
5 Quick New transmitter programmed.
8 Quick Unit reset: Occurs when the unit is reset to factory defaults.
RATE DESCRIPTION
• Unlocked by transmitter, system disarmed, Starter Kill disarmed.
• System has exited Valet Mode.
• Locked by transmitter while a door opened.
• System has entered Valet Mode.
Doors unlocked by transmitter with an intrusion occurred before unlocking
the doors.
OFF.
P. 12 User Guide
Loading...