Autostart AS-6105 SH Quick Guide
AUTOMATIC TRANSMISSION REMOTE STARTER & FULL-FEATURED ALARM SYSTEM
I. Learning a Transmitter
The AS-6105 SH/SR Transmitter is not delivered pre-programmed and must be code-learnt after the wiring of the
Module is completed. The system has the ability to learn up to 4 different transmitters, if a fifth Transmitter is learnt, the
code of the first Transmitter in memory will be lost. To erase all Transmitters from memory you must perform a Module
reset.
To program a new transmitter, do the following:
1. Ensure that the Hood is up, that the vehicle is not in Valet Mode and that the Ignition is OFF.
• Hold the Hood Pin-switch down for 4 seconds.
• Release the Pin-switch. The Parking Lights will come on.
• While the Parking Lights are on, immediately push and release the Pin-switch again.
The Parking Lights will stay on for up to 20 seconds.
2. Turn the Ignition Key to the IGNITION ON (RUN) position.
Wait until the Parking Lights go out, then turn the Ignition Key OFF, ON then back OFF again.
The L.E.D. will be flashing during the next step.
3. Press the LOCK button (or the UNLOCK button), wait 1 second and press the button again
… until the Parking Lights flash 5 times quickly and the Siren chirps twice.
You can alternatively press the button repeatedly until you see 5 flashes and hear 2 chirps.
4. To exit, close the Hood.
AS-6105 SH/SR
Quick Installation Guide
II. Valet Operation
When in Valet Mode, the Module will not carry out any remote start. The Alarm and Starter Kill will be disabled.
The AS-6105 SH/SR is equipped with a protected Push-button Valet Switch requiring the Ignition Key of the vehicle
in order to place the system in and out of Valet Mode. This will make it difficult for potential thieves to steal your vehicle
by hot-wiring your car after merely switching off the Valet.
Getting into Valet Mode
1. Turn the Ignition Key to the IGNITION ON (RUN) position.
2. Within 3 seconds, press and release the Valet button (the L.E.D. will come on and stay lit).
Getting out of Valet Mode
1. Turn the Ignition Key to the IGNITION ON (RUN) position.
2. Within 3 seconds, press and release the Valet button (the L.E.D. will go out).
If you try to remote-start the vehicle while it stands in Valet Mode, the Parking Lights will flash once, pause and flash
twice again.
III. Multi-speed Tach Learning
Tach signals may vary from vehicle to vehicle. The AS-6105 SH/SR system is designed to read a wide range of Tach
signals produced by recent Ignition systems. A Tach-learning procedure must be carried out every time a new Unit is
installed.
The procedure for Multi-speed Tach-learning is as follows:
1. Ensure that the Hood is up and that the Ignition is OFF.
• Hold the Hood Pin-switch down for 4 seconds.
• Release the Pin-switch. The Parking Lights will come on.
• While the Parking Lights are on, immediately push and release the Pin-switch again.
The Parking Lights will stay on for up to 20 seconds.
2. Press and hold the Brake Pedal and simultaneously press the LOCK and UNLOCK buttons on the Transmitter.
The Parking Lights will flash 4 times and the Siren will chirp 4 times.
3. Release the Brake Pedal; start the vehicle. Allow it to reach regular Engine idle speed.
The Parking Lights will go out when the Tach signal is detected.
4. Press and hold the Brake Pedal: if the Parking Lights flash 5 times the Tach signal has been learnt.
The Siren will chirp 1, 2 or 3 times to indicate which Tach mode has been detected.
H.1.00.S.2.00 Rev: 2.00 CA Fb – October 15, 2002 Manufactured in Canada by Autostart
IV. Programming Options
The AS-6105 SH/SR system, is equipped with three custom programming menus that allow the installer to custom-fit
the system outputs according to installation requirements.
The Options are designed to facilitate interfacing with all vehicle types.
To get into a Programming Mode, proceed as follows:
1. Ensure that the Hood is up and that the Ignition is OFF.
• Hold the Hood Pin-switch down for 4 seconds.
• Release the Pin-switch. The Parking Lights will come on.
• While the Parking Lights are on, immediately push and release the Pin-switch again.
The Parking Lights will stay on for up to 20 seconds.
2. Press and hold the Brake Pedal, then press one of the following buttons on the Transmitter (see Transmitter
Functions on page 7 for button layout):
• LOCK to enter Mode 1;
• UNLOCK to enter Mode 2;
• TRUNK to enter Mode 3.
The Parking Lights and the Siren will flash and chirp once, twice or three times to confirm entry into a Mode.
3. Release the Brake Pedal.
The Programming Menu will automatically start at Function 1. Once you select one of the Options of Function 1, you
will automatically move to the next Function. To select one of the four Options of a given Function, press the
corresponding button on the Transmitter (see Transmitter Functions on page 7 for button layout):
• LOCK button = Option 1
• UNLOCK button = Option 2
• TRUNK button = Option 3
• START button = Option 4
In each Function, once an Option has been selected the Parking Lights will flash 1, 2, 3 or 4 times (depending on the
selected Option).
Please note that, unlike Options within a Function, Functions within a Mode can only be accessed sequentially: the
Programming Menu will move from Function 1 to Function 2, 3, an so on. Therefore, whenever you enter a particular
Mode, be prepared to re-configure all the Functions of that Mode in ascending order.
MODE 1
* INDICATES DEFAULT SETTING
FUNCTION 1 – Ignition-controlled Door Locks
OPTION 1* Ignition Lock ENABLED
OPTION 2 Ignition Lock DISABLED
OPTION 3 Ignition LOCK ONLY
OPTION 4 Ignition UNLOCK ONLY
FUNCTION 2 – Secure Lock
OPTION 1* Secure Lock DISABLED (1-sec. Disarm pulse)
OPTION 2 Secure Lock ENABLED in Smart Mode
OPTION 3 Secure Lock DISABLED (0.5-sec. Disarm pulse)
OPTION 4 Secure Lock ENABLED in Standard Mode
FUNCTION 3 – Door lock pulse timing
OPTION 1* 7/10-sec. Lock/Unlock pulses
OPTION 2 4-sec. Lock/Unlock pulses
OPTION 3 7/10-sec. Lock pulse and two 1/10-sec. Unlock pulses
OPTION 4 1/10-sec. Lock/Unlock pulses
FUNCTION 4 – AUX 3 Programming
OPTION 1* Constant while the TRUNK button is pressed and Data out
OPTION 2 1-sec. Trunk 1 output when TRUNK button is pressed for 3 sec. with Ignition OFF or under remote run
OPTION 3 Trunk 2 output with Disarm/Rearm pulses
FUNCTION 5 – AUX 2 Programming
OPTION 1* Priority Door Access on 2
OPTION 2 Toggle ON/OFF with 30-second timeout
OPTION 3 Constant output while the button is pressed
OPTION 4 Priority Door Access on 2nd Unlock, and Car Finder
nd
UNLOCK and each subsequent Unlock, and Car Finder
MODE 2 * INDICATES DEFAULT SETTING
FUNCTION 1 – Home Valet Mode
OPTION 1 Home Valet ENABLED
OPTION 2* Home Valet DISABLED
P. 2 Quick Installation Guide AS-6105 SH/SR
Loading...