Autonics FS SERIES Instruction Manual

DRW161277AC

Auto

nics

8-PIN PLUG TYPE COUNTER

FS SERIES

I N S T R U C T I O N M A N U A L

Thank you for choosing our Autonics product.

Please read the following safety considerations before use.

Safety Considerations

Please observe all safety considerations for safe and proper product operation to avoid

※

hazards.

symbol represents caution due to special circumstances in which hazards may occur.

※

Failure to follow these instructions may result in serious injury or death.

Warning Caution

Warning

1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)

Failure to follow this instruction may result in re, personal injury, or economic loss.

2. Install on a device panel to use.

Failure to follow this instruction may result in electric shock or re.

3. Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in electric shock or re.

4. Check ‘Connections’ before wiring.

Failure to follow this instruction may result in re.

5. Do not disassemble or modify the unit.

Failure to follow this instruction may result in electric shock or re.

Caution

1. When connecting the power/sensor input and relay output, use AWG 20(0.50mm2) cable or over, and tighten the terminal screw with a tightening torque of 0.74 to 0.90N.m

Failure to follow this instruction may result in re or malfunc ion due to contact failure.

2. Use the unit within the rated specications.

Failure to follow this instruction may result in re or product damage.

3. Use dry cloth to clean the unit, and do not use water or organic solvent.

Failure to follow this instruction may result in electric shock or re.

4. Do not use the unit in the place where ammable/explosive/corrosive gas, humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be present.

Failure to follow this instruction may result in re or explosion.

5. Keep metal chip, dust, and wire residue from owing into the unit.

Failure to follow his instruc ion may result in re or product damage.

Dimensions

Bracket

44.9

※

The above specications are subject to change and some models may be discontinued without notice.

※

Be sure to follow cautions written in the instruction manual and the technical descriptions (catalog, homepage).

Failure to follow these instructions may result in personal injury or product damage.

12.3

10.5

63.8 14

■

□

Panel cut-out

Min. 65

30.5

48.6

□

[l]LE

Min. 65

(unit: mm)

Model

Model Display digit Size Output Power supply

FS4-1P2

FS4-1P4 100-240VAC 50/60Hz

FS5-I4 99999 (5-digit) Indicator 100-240VAC 50/60Hz

※8-pin

Model

Display digit 4-digit 5-digit Character size (W×H) 3 8×7.6mm 4×8mm

Power supply

Permissible voltage range 90 to 110% of rated voltage

Power consumption

Max. counting speed for COUNT IN

Return time Max. 500ms

Min. signal width RESET: approx. 20ms

Input method

One-shot output time 0 05 to 5 sec

Control output

Relay life cycle

Insulation resistance Over 100MΩ (at 500VDC megger) External power supply Max. 12VDC Memory retention Approx. 10 years (non-volatile memory) Dielectric strength 2,000VAC 50/60Hz for 1 min (between all terminals and case) Noise immunity

Vibration

Shock

Environment

Protection structure IP20 (front part, EC standard) Approval

Weight

※

1: The weight includes packaging. The weight in parenthesis is for unit only.

※

Environment resistance is rated at no freezing or condensation.

9999 (4-digit)

socket (PG-08, PS-08(N)) is sold separately.

D N W48×H48mm

I I

1-stage setting

Specications

1-stage setting FS4-1P2 FS4-1P4

Indicator

Contact

Mechanical Min. 5,000,000 operations

Electrical Min. 100,000 operations (250VAC 3A resistive load)

AC voltage ±2kV the square wave noise (pulse width 1㎲) by noise simulator

AC/DC voltage ±500V the square wave noise (pulse width 1㎲) by noise simulator

Mechanical

Malfunction

Mechanical 300m/s Malfunction 100m/s Ambient temp. -10 to 55℃, storage: -25 to 65 Ambient humi. 35 to 85%RH, storage: 35 to 85%RH

※

- -

24VACᜠ 50/60Hz, 24-48VDC

ᜡ

Max. 3 5VA (24VACᜠ 50/60Hz), Max. 2 3W (24-48VDC

Selectable 1cps/30cps/2kcps/5kcps (DIP switch)

Selectable voltage input (PNP) method or no-voltage input (NPN) method

[Voltage input (PNP) method]-input impedance: max. 10 8kΩ,

[No-voltage input (NPN) method]-short-circuit impedance: max. 470Ω,

Type Instantaneous SPST (1a) Capacity 250VACᜠ 3A, 30VDCᜡ 3A resistive load

0.75mm amplitude at frequency 10 to 55Hz (for 1 min) in each X, Y, Z direction for 1 hour 0 5mm amplitude at frequency 10 to 55Hz (for 1 min) in each X, Y, Z direction for 10 minutes

(approx. 30G) in each X, Y, Z direction for 3 times

(approx. 10G) in each X, Y, Z direction for 3 times

,'N:.

Approx. 130g (approx. 90g)

J J

±10% 50mA

ᜡ

100-240VACᜠ 50/60Hz

Max. 4.6VA (100-240VACᜠ 50/60Hz)

)

ᜡ

[H]: 5-30VDCᜡ, [L]: 0-2VDC

℃

Input Connection

24VAC 50/60Hz, 24-48VDC

short-circuit residual voltage: max. 1VDC,

open-circuit impedance: min. 100kΩ

Voltage input (PNP)

Solid state input (standard sensor: PNP output type sensor) Contact input

•

Sensor

(PNP output)

※

COUNT IN, RESET input part

Brown

Black

※

Blue

Counter

10.8kΩ

+12V

Inner circuit

Sensor

(PNP open collector output)

Brown

Black

※

Blue

Counter

10.8kΩ

+12V

Inner circuit

No-voltage input (NPN)

Solid state input (standard sensor: NPN output type sensor) Contact input

•

Sensor

(NPN output)

※

COUNT N, RESET input part

Connections

FS4-1P4

+ 0.6

PNP

NPN

FS5-I4

PNP

NPN

COUNT IN RESET

Counter

Brown

Black

※

Blue

0VDC

SOURCE: 100-240VAC 50/60Hz 4.6VA

0VDC

SOURCE: 100-240VAC 50/60Hz 3.8VA

+12V

5.4kΩ

Inner circuit

12VDC 50mA

CONTACT: 250VAC 3A, 30VDC 3A RESISTIVE LOAD

Sensor

(NPN open collector output)

Counter

Brown

Black

※

Blue

FS4-1P2

PNP

NPN

SOURCE: 24VAC 50/60Hz 3.5VA 24-48VDC 2.3W

+12V

5.4kΩ

Inner circuit

COUNT IN RESET

0VDC

FS5-I4

Max. 3 8VA (100-240VACᜠ

50/60Hz)

Approx. 120g (approx. 80g)

•

Counter

※

•

※

12VDC 50mA

+12V

Inner circuit

10.8kΩ

※

Counting speed

: Set as 1 or 30cps

Counter

+12V

5.4kΩ

Inner

circuit

※

Counting speed

: Set as 1 or 30cps

CONTACT: 250VAC 3A, 30VDC 3A RESISTIVE LOAD

DIP Switch Setting

Input logic (COUNT IN, RESET input)

•

SW1 Function

NPN (no-voltage input)

OFF

PNP (voltage input)

OFF

Up/Down mode

•

SW1 Function

Down mode

OFF

Up mode

OFF

Memory backup

•

SW1 Function

No memory backup

OFF

Memory backup

OFF

※

Output mode (SW2)

OFF

※

How to change settings

Power OFF → change settings → power ON → press

Output Operation Mode

One-shot output (0.05 to 5 sec) Self-holding output

·--

3 2 1

1■1■1■1

Set one-shot output time by front TIME volume switch.

SW1

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

--'ZJZ:y-

Output

RESET

Setting

Output

RESET

Setting

Output

2 23 34 5 6

Up mode

OFF

: I :

I • •

※

3 2 1 6 5 4 3 2 1

OFF

SW2

※

1: Indicator model (FS5-I4) does not have

no. 1, 2, 3 DIP switch of SW2 for output

operation mode setting.

Max. counting speed

•

SW1 Function

OFF

RESET

c:::::::::J

SW1

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

RESET

Setting

Output

Down mode Operation

OFF

Output operation mode

Memory backup

Max. counting speed N C (not used) Up/Down mode Input logic (NPN/PNP)

Factory default

SW1

5 4

[l]

5 4

[;I;]

5 4

1cps

30cps

2kcps

5 4

key or input signal (min. 20ms)

[!]

5kcps

After count-up, counting display value increases or decreases until reset signal input is applied and self-holding output is maintained.

After count-up, counting display value and selfholding output are maintained until reset signal input is applied.

When count-up, counting display value is reset and it counts simultaneously.

After count-up, counting display value is reset after one-shot output time and it counts simultaneously.

After count-up, counting display value increases or decreases until reset signal input is applied.

After count-up, counting display value is maintained while output is ON. Counting value is internally reset and it counts simultaneously.

After count-up, counting display value increases or decreases during one-shot output time.

Output maintains ON when counting display value is larger or equal than setting value.

Dot for Decimal Point

RESET

value

RUN mode

RESET

c:::::::::J

RESET

----

3 sec

Setting mode

Set decimal point

RESET

by front

Push the plug to the front.

※

In run mode, hold the 3 sec, and it enters setting mode [DP].

※

In setting mode, hold the over 3 sec, and it saves the setting and returns to RUN mode.

※

If there is no when entering setting mode, it returns to RUN mode.

Down mode

•

RESET

+Max. display

value

-Max. display

value

RESET

key for over

c:=i

RESET

c:=i

RESET

key input for 60 sec

c:=i

n n

RESET

c:::::::::J

3 sec

Detaching Case

※

Turn OFF the power before detaching the case.

Push the grooves at both side of the unit with a at head driver to the outside and push the plug part

to the front. The plug is detached.

Be sure not to be wounded when using a tool.

Counting Operation for Indicator (FS5-I4)

Up mode

•

+Max. display

※

- display is only for F, K, Q, S output operation mode and it cannot be set.

Error Display and Output Operation

Error Display Error description Troubleshooting

ERR0

※

When error occurs, the output turns OFF.

※

Indicator model does not have error display function.

Setting value is 0. Change the setting value anything but 0.

Cautions during Use

1. Follow instructions in ‘Cautions during Use’. Otherwise, It may cause unexpected accidents.

2. 24-48VDC, 24VAC power supply should be insulated and limited voltage/current or Class 2, SELV power supply device.

3. Use the product, 0.1 sec after supplying power.

4. When supplying or turning off the power, use a switch or etc. to avoid chattering.

5. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power.

6. In case of contact input, set count speed to low speed mode (1cps or 30 cps) to operate. If set to high speed mode (2kcps or 5kcps), counting error occurs due to chattering.

7. Keep away from high voltage lines or power lines to prevent inductive noise.

In case installing power line and input signal line closely, use line lter or varistor at power

line and shielded wire at input signal line. Do not use near the equipment which generates strong magnetic force or high frequency noise.

8. This product may be used in the following environments.

Indoors (in the environment condition rated in ‘Specications’)

①

Altitude max. 2,000m

②

Pollution degree 2

③

Installation category II

④

Major Products

Photoelectric Sensors Temperature Controllers

■

Fiber Optic Sensors Temperature/Humidity Transducers

■

Door Sensors SSRs/Power Controllers

■

Door Side Sensors Counters

■

Area Sensors Timers

■

Proximity Sensors Panel Meters

■

Pressure Sensors Tachometers/Pulse (Rate) Meters

■

Rotary Encoders Display Units

■

Connector/Sockets Sensor Controllers

■

Switching Mode Power Supplies

■

Control Switches/Lamps/Buzzers

■

I/O Terminal Blocks & Cables

■

Stepper Motors/Drivers/Motion Controllers

■

Graphic/Logic Panels

■

Field Network Devices

■

Laser Marking System (Fiber, Co₂, Nd: YAG)

■

Laser Welding/Cutting System

■

DRW161277AC

key for

Autonics FS SERIES Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual