Autel AutoLink AL419, AutoLink AL519, AutoLink AL439 User Manual

Page 1
Table of Contents
1. SAFETY PRECAUTIONS AND WARNINGS .............................................. 1
2. GENERAL INFORMATION .......................................................................... 2
2.1 ON-BOARD DIAGNOSTICS (OBD) II ............................................................. 2
2.2 DIAGNOSTIC TROUBLE CODES (DTCS) ........................................................ 2
2.3 LOCATION OF THE DATA LINK CONNECTOR (DLC) .................................... 3
2.4 OBD II READINESS MONITORS .................................................................... 4
2.5 OBD II MONITOR READINESS STATUS ......................................................... 5
2.6 OBD II DEFINITIONS .................................................................................... 6
2.7 OBD II MODES OF OPERATION .................................................................... 7
3. USING THE SCAN TOOL ............................................................................ 10
3.1 TOOL DESCRIPTION .................................................................................... 10
3.2 SPECIFICATIONS .......................................................................................... 12
3.3 ACCESSORIES INCLUDED............................................................................. 12
3.4 NAVIGATION CHARACTERS ........................................................................ 12
3.5 KEYBOARD .................................................................................................. 13
3.6 POWER ........................................................................................................ 13
3.7 DTC LOOKUP ............................................................................................. 13
3.8 SYSTEM SETUP ............................................................................................ 15
3.9 ABOUT ................................................................................................ ......... 24
3.10 VEHICLE COVERAGE .................................................................................. 24
3.11 PRODUCT TROUBLESHOOTING.................................................................... 25
4. REVIEW DATA ............................................................................................. 27
5. OBDII DIAGNOSTICS ................................................................................. 29
5.1 READING CODES ......................................................................................... 31
5.2 ERASING CODES .......................................................................................... 33
5.3 LIVE DATA .................................................................................................. 35
5.4 VIEWING FREEZE FRAME DATA ................................................................. 47
5.5 RETRIEVING I/M READINESS STATUS ......................................................... 48
5.6 VIEWING VEHICLE INFORMATION .............................................................. 55
5.7 CODE BREAKER .......................................................................................... 56
6. READY TEST ................................................................................................ 58
6.1 GENERAL INFORMATION ............................................................................ 58
6.2 READY TEST APPLICATION .......................................................................... 58
6.3 LED AND TONE INTERPRETATION .............................................................. 61
7. PRINT DATA ................................................................................................. 63
8. WARRANTY AND SERVICE ...................................................................... 65
8.1 LIMITED ONE YEAR WARRANTY ................................................................ 65
8.2 SERVICE PROCEDURES ................................................................................ 65
Page 2
1. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:
Always perform automotive testing in a safe environment. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, test equipment, etc. away from
all moving or hot engine parts.
Operate the vehicle in a well ventilated work area: Exhaust gases
are poisonous.
Put blocks in front of the drive wheels and never leave the vehicle
unattended while running tests.
Use extreme caution when working around the ignition coil,
distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
Put the transmission in PARK (for automatic transmission) or
NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
Keep a fire extinguisher suitable for gasoline/chemical/ electrical
fires nearby.
Don‟t connect or disconnect any test equipment while the
ignition is on or the engine is running.
Keep the scan tool dry, clean, free from oil/water or grease. Use a
mild detergent on a clean cloth to clean the outside of the scan tool, when necessary.
Page 3
2. General Information
2.1 On-Board Diagnostics (OBD) II
The first generation of On-Board Diagnostics (called OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On-Board Diagnostic regulations is called "OBD II".
The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning lamp (MIL) on the vehicle instrument panel to alert the driver typically by the phrase of “Check Engine” or “Service Engine Soon”. The system will also store important information about the detected malfunction so that a technician can accurately find and fix the problem. Here below follow three pieces of such valuable information:
1) Whether the Malfunction Indicator Light (MIL) is
commanded 'on' or 'off';
2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
3) Readiness Monitor status.
2.2 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problem found in the vehicle. These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consists of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The other four characters, all numbers, provide additional information on where the DTC originated and the operating conditions that caused it to set. Here below is an example to illustrate the structure of the digits:
Page 4
2.3 Location of the Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic scan tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver‟s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access
Identifying specific malfunctioning section of the systems
Systems
B=Body C=Chassis P=Powertrain U=Network
Code Type
Generic (SAE):
P0, P2, P34-P39 B0, B3 C0, C3 U0, U3. Manufacturer Specific: P1, P30-p33 B1, B2 C1, C2 U1, U2
Sub-systems
1= Fuel and Air Metering 2= Fuel and Air Metering 3= Ignition System or Engine Misfire 4= Auxiliary Emission Controls 5= Vehicle Speed Control and Idle
Controls 6= Computer Output Circuits 7= Transmission Controls 8= Transmission Controls
DTC Example
P 0 2 0 2
Page 5
the connector. If the DLC cannot be found, refer to the vehicle‟s
service manual for the location.
2.4 OBD II Readiness Monitors
An important part of a vehicle‟s OBD II system is the Readiness
Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits.
Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) defined by the U.S. Environmental Protection Agency (EPA). Not all monitors are supported by all vehicles and the exact number of monitors in any vehicle depends on the motor vehicle manufacturer‟s emissions control strategy.
Continuous Monitors -- Some of the vehicle components or systems
are continuously tested by the vehicle‟s OBD II system, while others
are tested only under specific vehicle operating conditions. The continuously monitored components listed below are always ready:
1Misfire 2Fuel System 3Comprehensive Components (CCM)
Once the vehicle is running, the OBD II system is continuously checking the above components, monitoring key engine sensors, watching for engine misfire, and monitoring fuel demands.
Non-Continuous Monitors -- Unlike the continuous monitors, many emissions and engine system components require the vehicle to be
Page 6
operated under specific conditions before the monitor is ready. These monitors are termed non-continuous monitors. For different ignition type engines, the available monitors are different too.
The following monitors are to be used for spark ignition engines only:
1) EGR System
2) O2 Sensors
3) Catalyst
4) Evaporative System
5) O2 Sensor Heater
6) Secondary air
7) Heated Catalyst
The following monitors are to be used for compression ignition engines only:
1) EGR System
2) NMHC Catalyst
3) NOx aftertreatment
4) Boost pressure system
5) Exhaust gas sensor
6) PM filter
2.5 OBD II Monitor Readiness Status
OBD II systems must indicate whether or not the vehicle‟s PCM‟s
monitor system has completed testing on each component.
Components that have been tested will be reported as “Ready”, or
“Complete”, meaning they have been tested by the OBD II system.
The purpose of recording readiness status is to allow inspectors to
determine if the vehicle‟s OBD II system has tested all the
components and/or systems. The power-train control module (PCM) sets a monitor to “Ready” or
“Complete” after an appropriate drive cycle has been performed. The drive cycle that enables a monitor and sets readiness codes to “Ready”
varies for each individual monitor. Once a monitor is set as “Ready”
Page 7
or “Complete”, it will remain in this state. A number of factors,
including erasing of diagnostic trouble codes (DTCs) with a scan tool or a disconnected battery, can result in Readiness Monitors being set
to “Not Ready”. Since the three continuous monitors are constantly
evaluating, they will be reported as “Ready” all of the time. If testing
of a particular supported non-continuous monitor has not been
completed, the monitor status will be reported as “Not Complete” or
“Not Ready.”
In order for the OBD monitor system to become ready, the vehicle should be driven under a variety of normal operating conditions. These operating conditions may include a mix of highway driving and stop and go, city type driving, and at least one overnight-off period. For specific information on getting your vehicle‟s OBD monitor system ready, please consult your vehicle owner‟s manual.
2.6 OBD II Definitions
Power-train Control Module (PCM) -- OBD II terminology for the
on-board computer that controls engine and drive train. Malfunction Indicator Light (MIL) -- Malfunction Indicator Light
(Service Engine Soon, Check Engine) is a term used for the light on the instrument panel. It is to alert the driver and/or the repair technician that there is a problem with one or more of vehicle's systems and may cause emissions to exceed federal standards. If the MIL illuminates with a steady light, it indicates that a problem has been detected and the vehicle should be serviced as soon as possible. Under certain conditions, the dashboard light will blink or flash. This indicates a severe problem and flashing is intended to discourage vehicle operation. The vehicle onboard diagnostic system can not turn the MIL off until necessary repairs are completed or the condition no longer exists.
DTC -- Diagnostic Trouble Codes (DTC) that identify which section of the emission control system has malfunctioned.
Enabling Criteria -- Also termed Enabling Conditions. They are the vehicle-specific events or conditions that must occur within the engine before the various monitors will set, or run. Some monitors
Page 8
require the vehicle to follow a prescribed “drive cycle” routine as part
of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle.
OBD II Drive Cycle -- A specific mode of vehicle operation that provides conditions required to set all the readiness monitors
applicable to the vehicle to the “ready” condition. The purpose of
completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics. Some form of a drive cycle needs to be
performed after DTCs have been erased from the PCM‟s memory or after the battery has been disconnected. Running through a vehicle‟s complete drive cycle will “set” the readiness monitors so that future
faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. For vehicle specific drive cycle, consult the vehicle‟s Owner‟s Manual.
Freeze Frame Data -- When an emissions related fault occurs, the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM, vehicle speed, air flow, engine load, fuel pressure, fuel trim value, engine coolant temperature, ignition timing advance, or closed loop status.
2.7 OBD II Modes of Operation
Here is a basic introduction to the OBD II communication protocol. Mode byte: The first byte in the stream is the mode number. There
are 10 modes for diagnostic requests. The first byte in the response data bytes is this same number plus 64. For example, a mode 1 request would have the first data byte = 1, and the response would have the first data byte = 65. Here is a brief description of the modes:
Mode $01 – Identifies the Powertrain information and shows current data available to the scan tool. This data includes: DTC set,
status of on-board tests, and vehicle data such as engine RPM, temperatures, ignition advance, speed, air flow rates, and closed loop status for fuel system.
Page 9
Mode $02Displays Freeze Frame data. Same data as in mode 1, but it was captured and stored when a malfunction occurred and a DTC was set. Some of the PIDs for mode one are not implemented in this mode.
Mode $03 – Displays the type of powertrain or emission related DTCs stored by a 5 digit code identifying the faults. There may be
more than one response message if there are more trouble codes than will fit in the data bytes of the response message, or if there are more than one ECU computer responding.
Mode $04Used to clear DTCs and Freeze Frame data. This clears all diagnostic trouble codes that may be set including freeze frame data and readiness monitors.
Mode $05Oxygen Sensor Test Results. This mode displays the oxygen sensor monitor screen and the test results gathered about the oxygen sensor.
There are ten numbers available for diagnostics:
1. $01 Rich-to-Lean O2 sensor threshold voltage.
2. $02 Lean-to-Rich O2 sensor threshold voltage.
3. $03 Low sensor voltage threshold for switch time
measurement.
4. $04 High sensor voltage threshold for switch time
measurement.
5. $05 Rich-to-Lean switch time in ms.
6. $06 Lean-to-Rich switch time in ms.
7. $07 Minimum voltage for test.
8. $08 Maximum voltage for test.
9. $09 Time between voltage transitions in ms.
Mode $06Non-continuously Monitored Systems test results. There are typically a minimum value, a maximum value, and a current value for each non-continuous monitor. This data is optional, and it is defined b a given vehicle maker if it‟s used.
Mode $07 – Request for DTCs (pending) from Continuously Monitored Systems after a single driving cycle has been performed to determine if repair has fixed a problem. This used
Page 10
by service technicians to verify repair was performed properly and after clearing diagnostic trouble codes.
Mode $08 – This special Control Mode requests control of the on-board system, test, or component bi-directionally (where applicable). This mode is manufacturer specific.
Mode $09 – Reports vehicle information. This information
includes vehicle VIN number and calibration information stored in the vehicle ECUs.
Mode $0A – Request Emission-Related Diagnostic Trouble Codes with Permanent Status. This mode is required for all
emissions-related DTCs. The presence of permanent DTCs at an inspection without the MIL illuminated is an indication that a proper repair was not verified by the on-board monitoring system.
Page 11
10
3. Using the Scan Tool
3.1 Tool Description
1) OBD II CONNECTOR – Connects the scan tool to the
vehicle‟s Data Link Connector (DLC).
2) LCD DISPLAY – Indicates test results.
3) GREEN LED – Indicates that engine systems are running
normally (The number of monitors on the vehicle which are active and performing their diagnostic testing is in the allowed limit, and no DTCs are present).
Page 12
11
4) YELLOW LED – Indicates there is a possible problem. A
Pending DTC is present and/or some of the vehicles emission monitors have not run their diagnostic testing.
5) RED LED – Indicates there is a problem in one or more of
the vehicles systems. The red LED is also used to show that DTCs are present. DTCs are shown on the Scan Tools display. In this case, the MIL lamp on the vehicles instrument panel will light steady on.
6) One-Click I/M Readiness Key – Quick-checks State
Emissions readiness and drive cycle verification.
7) ESC BUTTON – Cancels a selection (or action) from a
menu or returns to the previous screen.
8) LEFT SCROLL BUTTON – When look up DTC
definitions, moves to previous character and views additional information on previous screens if DTC definition covers more than one screen; deselect all marked PID data when viewing or recording customized live data list; views previous frames of recorded data when playing back live data. It is also used to update DTC library when pressed.
9) HELP BUTTON – Provides help information and Code
Breaker function.
10) UP SCROLL BUTTON – Moves up through menu and
submenu items in menu mode. When more than one screen of data is retrieved, moves up through the current screen to the previous screens for additional data.
11) OK BUTTON – Confirms a selection (or action) from a
menu.
12) RIGHT SCROLL BUTTON – When look up DTC
definitions, moves to next character and view additional information on next screens if DTC definition covers more than one screen; selects/deselects PID data when viewing or
Page 13
12
recording customized live data list, and views next frames of data when playing back live data.
13) DOWN SCROLL BUTTON – Moves down through
menu and submenu items in menu mode. When more than one screen of data is retrieved, moves down through the current screen to next screens for additional data.
14) USB CONNECTOR – Connects the scan tool to the PC for
printing and upgrading.
3.2 Specifications
1) Display: TFT color display (320 x 240 dpi)
2) Operating Temperature: 0 to 60°C (32 to 140 F°)
3) Storage Temperature: -20 to 70°C (-4 to 158 F°)
4) External Power: 8.0 to 18.0 V power provided via vehicle
battery
5) Dimensions: Length Width Height
199 mm (7.83”) 104.5 mm (4.11”) 37.5 mm (1.48”)
6) Weight: 0.28kg(without wire) 0.484kg(with wire)
3.3 Accessories Included
1) User’s Manual -- Instructions on tool operations.
2) CD -- Includes user‟s manual, MaxiLink update software, and
etc.
3) OBD2 cable -- Provides power to tool and communicates
between tool and vehicle.
4) USB cable -- Used to upgrade the scan tool, and to print
retrieved data.
5) Carry case -- A nylon case to store the scan tool when not in use.
3.4 Navigation Characters
Characters used to help navigate the scan tool are:
Page 14
13
1) $ -- Identifies the control module number from which data is
retrieved.
2) ?-- Indicates help or code breaker information is available.
3) G-- Indicates graphic viewing is available.
3.5 Keyboard
No solvents such as alcohol are allowed to clean the keypad or display. Use a mild nonabrasive detergent and a soft cotton cloth. Do not soak the keypad as the keypad is not waterproof.
3.6 Power
The scan tool is powered via the vehicle Data Link Connector (DLC). Just follow the steps below to turn on the scan tool:
1) Connect the OBD II Cable to scan tool.
2) Find DLC on vehicle.
A plastic DLC cover may be found for some vehicles and you
need to remove it before plugging the OBD2 cable.
3) Plug OBD II cable to the vehicle‟s DLC.
3.7 DTC Lookup
The DTC Lookup function is used to search for definitions of DTCs stored in the DTC library and for code breaker information.
1) From Main Screen (Figure 3.1), use the UP/DOWN scroll button
and LEFT/RIGHT scroll button to select DTC Lookup and press the OK button.
Page 15
14
Figure 3.1
2) From DTC Lookup screen, use the LEFT/RIGHT button to
move to the desired character, use the UP/DOWN button to change selected digit/character and press the OK button to confirm. (Figure 3.2)
Figure 3.2
3) View the DTC definition on screen. When DTC definition covers
more than one screen, use the LEFT/RIGHT button or UP/DOWN button to view additional information on previous/next screens.
For manufacturer specific codes, you need to select a vehicle
make on an additional screen to look for DTC definitions.
If definition could not be found (SAE or Manufacturer
Specific), the scan tool displays “Please refer to vehicle service manual!
For code breaker information, you need to press the ?Help
button.
DTC Lookup
P 0 0 0 1
Left
Right
Change digit
OK
Confirm
ESC
Exit
Page 16
15
In the Code Breaker screen, there are three options to assist user to understand DTC more: System Description and Quick Check to read detailed description of DTCs, General Notes to view helpful repair information of DTCs.
4) To view previous or next DTC in the built-in DTC library, use the
LEFT/RIGHT button.
5) To enter another DTC, press the ESC button to return to previous
screen.
6) To exit to Main Screen, press the ESC button.
3.8 System Setup
The scan tool allows you to make the following adjustments and settings:
1) Language: Selects the desired language.
2) Configure Monitors: Sets the monitors you want to test.
3) Unit of measure: Sets the unit of measure to English or Metric.
4) Key Beep Set: Turns on/off beep.
5) Status Beep Set: Turns on/off the I/M Readiness Status beep.
6) Tool Self-test: Checks if the LCD display, LED lamps and
keyboard are working normally.
7) Update Mode: Accesses the Update Mode.
Settings of the unit will remain until change to the existing
settings is made.
To enter the Setup menu
From the Main Screen: Use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select Setup, and press the OK button.
Follow the instructions to make adjustments and settings as described in the above setup options. (Figure 3.3)
Page 17
16
Figure 3.3
Language Setup
English is the default language.
1) From System Setup screen, use the UP/DOWN scroll button to
select Language, and press the OK button.
2) Use the UP/DOWN scroll button to select the desired language
and press the OK button to save your selection and return to previous screen. We provide three language options currently.
Figure 3.4
Configure Monitors
From System Setup screen, use the UP/DOWN scroll button to select Configure Monitors, and press the OK button.
Language 1/3
English Français ? Español
System Setup 1/7
Language
Configure Monitors ? Unit of Measure Key Beep Set Status Beep Set
Tool Self-test
Page 18
17
Figure 3.5
In this menu, you could configure the monitors required to test spark ignition and compression ignition, the number of monitors to pass diagnosis, and restore the default settings.
1) Spark IGN Required Monitors
From Configure Monitors screen, use the UP/DOWN scroll button to select Spark IGN Required Monitors, and press the OK button.
The monitors for spark ignition engines show as below:
Spark IGN Required Monitors
MIS
EVAP
FUEL
AIR
CCM
O2S
CAT
HTR
HCAT
EGR
2) Compression IGN Required Monitors
From Configure Monitors screen, use the UP/DOWN scroll button to select Compression IGN Required Monitors, and press the OK button.
The monitors for compression ignition engines show as below:
Configure Monitors 1/4
Spark IGN Required Monitors
Compression IGN Required Monitors Allowed INC Monitors ? Reset Factory Default
Page 19
18
Compression IGN Required Monitors
MIS √ BP
FUEL
EGS
CCM
PM
HCCAT
EGR
NCAT
3) Allowed INC Monitors
From Configure Monitors screen, use the UP/DOWN scroll button to select Allowed INC Monitors, and press the OK button.
Emissions tests vary depending on the geographic or regional area in which the vehicle is registered. So the scan tool provides a more flexible way to meet different standards, which allows the user to select 0, 1, 2, 3 not complete monitors in test.
4) Reset Factory Default
From Configure Monitors screen, use the UP/DOWN scroll button to select Reset Factory Default, and press the OK button.
It will restore the default configuration settings in the Configure
Monitors menu, and delete any customized settings. In this case, Spark IGN Required Monitors and Compression IGN Required Monitors will include all the available monitors, and the Allowed INC Monitors will be set to 1.
The tool will display an information message to ask for your confirmation. Select Yes to proceed and No to exit without change.
Unit of Measure
Metric is the default measurement unit.
1) From System Setup screen, use the UP/DOWN scroll button to
select Unit of Measure and press the OK button.
Page 20
19
2) From Unit of Measure screen, use the UP/DOWN scroll button
to select the desired unit of measurement. (Figure 3.6 )
Figure 3.6
3) Press the OK button to save your selection and return to previous
menu.
Key Beep Set
This function allows you to turn on/off the build-in speaker for key pressing.
The default setting is Beep On.
1) From System Setup screen, use the UP/DOWN scroll button to
select Key Beep Set and press the OK button.
2) From Key Beep Set menu, use the UP/DOWN scroll button to
select Beep ON or Beep OFF to turn on/off the beep.
Figure 3.7
Unit of Measure 1/2
English Metric ?
Key Beep Set 1/2
Beep ON Beep OFF ?
Page 21
20
3) Press the OK button to save your selection and return to
previous menu.
Status Beep Set
The default setting is Beep On.
This function allows you to turn on/off the build-in speaker for the LEDs in diagnostic testing. Different audio tone corresponds to different LED lamp. This function is invaluable when working in bright areas where LED illumination alone is not sufficient.
1) From System Setup screen, use the UP/DOWN scroll button to
select Status Beep Set and press the OK button.
2) From Status Beep Set menu, use the UP/DOWN scroll button to
select Beep ON or Beep OFF to turn on/off the beep.
Figure 3.8
3) Press the OK button to save your selection and return to previous
menu.
Tool Self-test
The Tool Self-test function checks if the display, LED lamps and keyboard are working properly.
A. Display test
Status Beep Set 1/2
Beep ON Beep OFF ?
Page 22
21
The Display Test function checks if the LCD display is working normally.
1) From System Setup screen, use the UP/DOWN scroll button to
select Tool Self-test, and press the OK button.
2) Select Display Test from Tool Self-test menu and press the OK
button to start test. (Figure 3.9 )
Figure 3.9
3) Look for missing spots in the red, green, blue, black and white
LCD display.
4) When completed, press the ESC button to exit.
B. Keyboard Test
The Keyboard Test function verifies if the keys are functioning properly.
1) Use the UP/DOWN scroll button to select Keyboard Test from
the Tool Self-test menu, and then press the OK button.
2) Press any key to start test. When you press a key, the key name
should be observed on the display. If the key name does not show up, then the key is not functioning properly. (Figure 3.10)
Tool Self-test 1/3
Display Test
Keyboard Test LED Test ?
Page 23
22
Figure 3.10
3) Double press ESC to return to previous menu.
C. LED Test
The LED Test function verifies if the I/M Readiness LED indicator lamps are functioning properly.
1) Use the UP/DOWN scroll button to select LED Test from the
Tool Self-test menu, and then press the OK button.
2) In the LED Test menu, use the UP/DOWN scroll button to
select one or more LED lamps to check. The LED should turn on or off according to the selected commands.
Figure 3.11
3) When completed, press the ESC button to exit.
Update Mode
This function allows you to update the scan tool software and DTC library through a computer.
Keyboard Test
Press any key to
start test
key:
Double [ESC] to return
LED Test 1/3
RED LED ON
YELLOW LED ON GREEN LED ON
Page 24
23
To update your scan tool, you need the following items.
AutoLink AL419 A PC or laptop with USB ports A USB cable
1) Download the programs to be updated to your computer.
2) Run the MaxiLinkII Tool Kit in your computer. (Figure 3.12)
3) Connect the scan tool to your computer through the USB cable
provided.
4) From System Setup screen in scan tool, use the UP/DOWN
scroll button to select Update Mode, and press the OK button.
5) Select the programs to be updated in your computer. There are
two types of programs: operating system and DTC library. (Figure 3.12)
6) Click Update in the MaxiLinkII Tool Kit window to begin
updating.
Figure 3.12
7) During the update procedure, the scan tool displays a message
Update Program. Please wait”.
8) When the update has finished, the scan tool will display a
message Program Update has been done!
Page 25
24
9) Restart the scan tool to finish the whole update.
NOTE: When you made a wrong choice and the scan tool is unable to work properly, you may need to update the programs. To hold LEFT scroll button and power on the scan tool, you will enter the Update Mode forcedly. Then follow the update procedure to refresh the program.
3.9 About
The About function allows viewing of some important information such as serial number and software version number of the scanner.
1) From Main Screen (Figure 3.1), use the UP/DOWN scroll
button and LEFT/RIGHT scroll button to select About and press the OK button; wait for the About screen to appear.
2) View tool information on screen.
Figure 3.13
3.10 Vehicle Coverage
The AutoLink AL419 OBDII/EOBD Scanner is specially designed to work with all OBD II compliant vehicles, including those equipped with next-generation protocol -- Control Area Network (CAN). It is required by EPA that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant and this includes all Domestic, Asian and European vehicles.
Page 26
25
A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label which is located under the hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the label will designate “OBD II Certified”. Additionally, Government regulations mandate that all OBD II compliant vehicles must have a “common” sixteen-pin Data Link Connector (DLC).
For your vehicle to be OBD II compliant it must have a 16-pin DLC (Data Link Connector) under the dash and the Vehicle Emission Control Information Label must state that the vehicle is OBD II compliant.
3.11 Product Troubleshooting
This part describes problems that you may encounter while using the scan tool.
Vehicle Linking Error
A communication error occurs if the scan tool fails to communicate
with the vehicle‟s ECU (Engine Control Unit). You need to do the following to check up:
Verify that the ignition is ON. Check if the scan tool‟s OBD II connector is securely
connected to the vehicle‟s DLC.
Verify that the vehicle is OBD2 compliant. Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and continue the testing.
Verify the control module is not defective.
Operating Error
If the scan tool freezes, then an exception occurs or the vehicle‟s ECU (Engine Control Unit) is too slow to respond to requests. You need to do the following to reset the tool:
Reset the scan tool.
Page 27
26
Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and continue the testing.
Scan tool doesnt power up
If the scan tool wont power up or operates incorrectly in any other way, you need to do the following to check up:
Check if the scan tool‟s OBD II connector is securely connected
to the vehicle‟s DLC;
Check if the DLC pins are bent or broken. Clean the DLC pins if
necessary.
Check vehicle battery to make sure it is still good with at least 8.0
volts.
LED lamps not working
If you turn on the scan tool and perform the I/M Readiness test but the LED lamps are not working, there may be several possible causes, including bad connection and ignition off. In this case, follow these steps to check the scan tool.
Make sure the OBD II cable is connected to the DLC securely. Verify the ignition key is in the KOER position. Run the LED Test in the System Setup menu. (see 3.8 System
Setup). If the scan tool did not pass this test, there is a problem with the LED lamp. Please contact Autel Tech Support or your local selling agent.
Page 28
27
4. Review Data
The Review Data function allows viewing of data from last test recorded by the scan tool.
1) Use the UP/DOWN scroll button and LEFT/RIGHT scroll
button to select Review Data from Main Screen, and press the OK button. (Figure 3.1)
2) Use the UP/DOWN scroll button to select the desired item from
Review Data menu, and press the OK button. (Figure 4.1 )
Figure 4.1
If no data from previously tested vehicle is recorded, only
Modules Present data containing module ID and protocol type can be reviewed. (Figure 4.2)
Figure 4.2
Diagnostics results can be reviewed from this list only when
any trouble code is detected in previous tests.
Review Data 1/6
Live Data
Pending Codes View Freeze Frame I/M Readiness On-Board Mon. Test Modules Present
Review Data 1/1
Modules Present
Page 29
28
3) Review selected data on screen. (Figure 4.3 )
Figure 4.3
NOTE: If there is no data stored for selected item, a “Not Supported or Stored No Data!” message shows on the screen.
1/1
C1201
Engine Control System Malfunction ?
Page 30
29
5. OBDII Diagnostics
When more than one vehicle control module is detected by the scan tool, you will be prompted to select the module where the data may be retrieved. The most often to be selected are the Power train Control Module [PCM] and Transmission Control Module [TCM].
CAUTION: Don’t connect or disconnect any test equipment with
ignition on or engine running.
1Turn the ignition off. 2Locate the vehicle‟s 16-pin Data Link Connector (DLC). 3Plug the scan tool cable connector into the vehicle‟s DLC. 4Turn the ignition on. Engine can be off or running. 5Turn on the scan tool. Use the UP/DOWN scroll button to select
OBDII/EOBD from the Main Screen (Figure 3.1).
6Press the OK button to wait for the Menu to appear. A sequence
of messages displaying the OBDII protocols will be observed on the display until the vehicle protocol is detected.
If the scan tool fails to communicate with the vehicle’s
ECU (Engine Control Unit) more than three times, a “LINKING ERROR!” message shows up on the display.
Verify that the ignition is ON; Check if the scan tool‟s OBD II connector is securely
connected to the vehicle‟s DLC;
Verify that the vehicle is OBD2 compliant; Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and repeat the procedure from step 5.
If the “LINKING ERROR” message does not go away,
then there might be problems for the scan tool to communicate with the vehicle. Contact your local
distributor or the manufacturer’s customer service
department for assistance.
7You will be prompted to erase previously stored data. Figure
5.1
Page 31
30
Review previously stored data thoroughly before erasing.
Figure 5.1
If no data is stored in the scan tool, above prompt will not
show up.
8If you wish to erase the data, press the OK button; if you do not
want to erase the data, press ESC to exit or use LEFT/RIGHT button to select NO and press OK to continue.
9View a summary of system status (MIL status, DTC counts,
Monitor status) on screen. (Figure 5.2 ) Wait a few seconds or press any key for Diagnostic Menu (Figure 5.4) to come up.
Figure 5.2
If more than one module is detected, you will be prompted to
select a module before testing.
System Status
Codes Found 6 Ignition Type Spark Monitors N/A 3 Monitors OK 3 Monitors INC 5
Diagnostic
Erase previously
stored data to save data from this test?
YES NO
Page 32
31
Figure 5.3
Use the UP/DOWN scroll button to select a module and press
the OK button.
5.1 Reading Codes
Reading Codes can be done with the key on engine off (KOEO)
or with the key on engine running (KOER).
Stored Codes are also known as “hard codes, which are fault
codes, or trouble codes that have been stored in the vehicle computer memory because the faults have reoccurred for more than a specified amount of key-cycles. These codes will cause the control module to illuminate the malfunction indicator light (MIL) when emission-related fault occurs.
Pending Codes are also referred to as “maturing codes” or
“continuous monitor codes”. They indicate problems that the
control module has detected during the current or last driving cycle but are not considered serious yet. Pending Codes will not turn on the malfunction indicator lamp (MIL). If the fault does not occur within a certain number of warm-up cycles, the code clears from memory.
Permanent Codes are DTCs that are "confirmed" and are
retained in the non-volatile memory of the computer until the appropriate monitor for each DTC has determined that the malfunction is no longer present and is not commanding the MIL on. Permanent DTC shall be stored in non-volatile memory and may not be erased by any diagnostic services or by disconnecting power to ECU.
Control Module 1/2
Engine
Module $A4 ?
Page 33
32
1) Use UP/DOWN scroll button to select Read Codes from
Diagnostic Menu and press OK button.
Figure 5.4
2) Use the UP/DOWN scroll button to select Stored Codes or
Pending Codes from the Read Codes menu and press the OK button.
Figure 5.5
If there is not any Diagnostic Trouble Code, the display
indicates No (pending) codes are stored in the module! Wait a few seconds or press any key to return to previous screen.
NOTE: Permanent Codes function is available for merely vehicles supporting the CAN protocols.
3) View DTCs and their definitions on screen.
Diagnostic Menu 1/7
Read Codes
Erase Codes Live Data ?
View Freeze Frame I/M Readiness
Vehicle Info
Read Codes 1/3
Stored Codes
Pending Codes Permanent Codes ?
Page 34
33
Figure 5.6
4) If more than one DTC is found, use the LEFT/RIGHT scroll
button to check all the codes.
If retrieved DTCs contain any manufacturer specific or
enhanced codes, a Manufacturer specific codes are found! Press any key to select vehicle make!” message comes up prompting you to select vehicle manufacturer to view DTC definitions. Use UP/DOWN scroll button to select manufacturer and then press OK button to confirm.
Figure 5.7
If the manufacturer of your vehicle is not listed, use the
UP/DOWN scroll button to select Other and press the OK button.
5.2 Erasing Codes
CAUTION: Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle’s on-board
computer, but also “Freeze Frame” data and manufacturer specific
1/1
P1633 $10 BUICK
Ignition 0 Switch Circuit
?
Vehicle Manufacturer 1/28
BUICK
BMW CADILLAC ? CHEVROLET CHRYSLER FORD
Page 35
34
enhanced data. Further, the I/M Readiness Monitor Status for all vehicle monitors is reset to Not Ready or Not Complete status. Do not erase the codes before the system has been checked completely by a technician.
NOTE: Erasing codes does not mean that trouble codes in ECU have been eliminated completely. As long as there is fault with the vehicle, the trouble codes keeps on presenting.
This function is performed with key on engine off (KOEO). Do
not start the engine.
1) Use the UP/DOWN scroll buttons to select Erase Codes from
Diagnostics Menu and press the OK button. (Figure 5.4)
2) A warning message comes up asking for your confirmation.
Figure 5.8
If you do not want to proceed with erasing codes, press ESC
button or use LEFT/RIGHT scroll button to select NO to exit. A message of Command Cancelled! show ups. Wait a few seconds or press any key to return to Diagnostic Menu.
3) Press the OK button to confirm. If the codes are cleared successfully, an “Erase Done!
confirmation message shows on the display.
Erase Codes
Erase trouble codes!
Are you sure?
YES NO
Page 36
35
Figure 5.9
If the codes are not cleared, then an “Erase Failure. Turn
Key on with Engine off! message appears.
Figure 5.10
4) Press any button to return to Diagnostic Menu.
5.3 Live Data
In this function, you can not only read the live data but also record
data for later review.
Viewing Data
The View Data function allows viewing of live or real time PID
data of vehicle’s computer module(s).
1) To view live data, use the UP/DOWN scroll button to select Live
Data from Diagnostic Menu and press the OK button. (Figure
5.4)
Erase Codes
Erase Failure. Turn Key on with Engine Off!
Press any key to con.
Erase Codes
Erase Done!
Press any key to con.
Page 37
36
2) Wait a few seconds while the scan tool validates the PID MAP.
(Figure 5.11)
Figure 5.11
3) Use the UP/DOWN scroll button to select View Data from Live
Data menu and press the OK button.
Figure 5.12
Viewing Complete Data Set
1) To view complete set of data, use UP/DOWN scroll button to
select Complete Data Set from View Data menu and press the OK button.
Live Data
Reading PID.01
- Please Wait -
……………… .Live Data 1/3.
View Data
Record Data ? Playback Data
Page 38
37
Figure 5.13
2) View live PIDs on the screen. Use the UP/DOWN scroll button
for more PIDs if additional information is available on more than one page.
Figure 5.14
The number x to the right of the screen indicates sequence
of the highlighted item.
To view full name of the highlighted PID, press the
?
button.
If the G icon appears when a PID is highlighted, graphic
information is available. Press OK to view graph.
…………………View Data 1/3.
Complete Data Set
Custom Data Set
Unit of Measure ?
Live Data 6
DTC_CNT 0 FUELSYS1 0L FUELSYS2 -- ?
LOAD_PCT (%) 0.0 ETC() -40
SHRTFT1 (%) 99.2
Page 39
38
Figure 5.15
3) Press the ESC button to return to previous menu.
Viewing Custom Data Set
1) To view customized PID data, use the UP/DOWN scroll button
to select Custom Data Set from View Data menu and press the OK button. (Figure 5.13)
2) Observe on-screen instructions.
Figure 5.16
3) Use the RIGHT button to deselect/select data parameters, and
use the UP/DOWN scroll button to move up and down. Selected parameters are marked with solid squares.
……………Custom Data Set……… …..
[
] – Select/Deselect
[
] – Deselect all [OK] – Confirm [ESC] – Cancel
Press any key to continue.
Page 40
39
Figure 5.17
The number x to the upper right corner of the screen
indicates sequence of highlighted item; and #x are the order that the parameters are selected and will be displayed.
If you want to deselect all marked items or select all items,
press the LEFT button. A message comes up to ask for your confirmation.
Figure 5.18
If you decide to deselect these items, press OK; if you decide
not to, press ESC or use the LEFT/RIGHT scroll button to select NO to continue PID selections.
4) Press the OK button to view selected PIDs on screen.
…………..Custom Data Set 4/26
DTC_CNT FUELSYS1 FUELSYS2 ? LOAD_PCT #01 ECT SHRTFT1
………………Deselect All………………….
Deselect all
selected PIDs?
YES NO
Page 41
40
Figure 5.19
5) Use the ESC button to return to previous menu.
Recording Data
The Record Data function allows recording vehicle modules Parameter Identification (PID) data to help diagnose intermittent vehicle problems. A recording includes 5 frames of live data before trigger event and several frames after trigger event.
There are two trigger modes used to record data:
A. Manual Trigger - allows user to press the OK button to start
recording.
B. DTC Trigger - automatically records PID data when a fault that
causes a DTC to set is detected by vehicle.
CAUTION: DO NOT try to drive and operate the scan tool at the same time! Always have another person operate the scan tool while driving.
To record live data, use the UP/DOWN scroll button to select Record Data from Live Data menu and press the OK button.
( Figure 5.12)
Recording Complete Data Set
1) To record complete set of live data, use the UP/DOWN scroll
button to select Complete Data Set from Record Data menu and press the OK button.
………………….Live Data 4 .
DTC_CNT 0 FUELSYS2 0L
ETC() -40 ?
SHRTFT1 (%) 99.2
Page 42
41
Figure 5.20
2) Use the UP/DOWN scroll button to select a trigger mode and
press the OK button.
Figure 5.21
If data from previously tested vehicle is not erased, data from
current test will be stored in a temporary cache.
3) Use the UP/DOWN scroll button to select a memory location
and press the OK button.
Figure 5.22
………………..Record Data 1/3..
Complete Data Set
Custom Data Set Unit of Measure ?
…………….Select Memory 1/3..
Location #1 *
Location #2 Location #3 ?
…….……Pick Trigger Mode 1/2
Manual Trigger
DTC Trigger ?
Page 43
42
The asterisk (*) icon on the screen indicates that there is a
previous recording in the memory location.
If you select a location marked with an asterisk (*) icon, a
message prompting to overwrite old recording displays.
Figure 5.23
If you wish to proceed with overwriting the old recording,
press the OK button; if you do not wish to overwrite it, use the LEFT/RIGHT button to select NO or press the ESC button to pick another memory location.
4) Observe on-screen instructions. If Manual Trigger is selected, following screen shows:
Figure 5.24
If DTC Trigger is selected, following screen shows:
……………Manual Trigger……………...
Ready to record! Press [ENTER] to start recording… Press [ESC] to exit
Select Memory ...
A previous recording
exists! Do you want to overwrite it?
YES NO
Page 44
43
Figure 5.25
5) Wait for DTC to trigger recording or press OK to start recording.
(Figure 5.26)
Drive till a DTC is detected when DTC Trigger is selected. If no
DTCs are detected, press ESC to exit recording.
Figure 5.26
The number x/x...” to the upper right corner of the screen
indicates the maximum frames that can be recorded and the number of recorded frames.
6) The scan tool keeps recording PID data until user presses the
ESC button, selected memory location is full, or it completes recording. A message prompting to playback data shows on the screen.
…….Recording. 5/46 ..
DTC_CNT 0 FUELSYS1 0L FUELSYS2 -- ? LOAD_PCT(%) 0.0 ETC() -40
SHRTFT1(%) 99.2
………………….DTC Trigger……………..
Waiting for DTC to trigger recording…
Press [ESC] to exit
Page 45
44
Figure 5.27
If you wish to playback recorded data, press the OK button; if
you do not wish to playback, press the ESC button, or use LEFT/RIGHT button to select NO and press the OK button to return to Record Data menu.
Recording Custom Data Set
1) To record customized data, use the UP/DOWN scroll button to
select Custom Data Set from Record Data menu and press the OK button. (Figure 5.20)
2) Observe on-screen instructions. (Figure 5.16). Press the OK
button to continue; press the ESC button, or use LEFT/RIGHT button to select NO and press the OK button to return to Record Data menu.
3) Use the RIGHT button select/deselect data parameters. Selected
parameters are marked with solid squares. Press the OK button to confirm. (Figure 5.17)
If you wish to deselect all marked items, press LEFT button. A message comes up to ask for your confirmation.( Figure
5.18)
If you decide to deselect these items, press OK; if you decide
not to, press the ESC button, or use the UP/DOWN button to select NO and press OK to continue PID selections.
Record Data
Recording Done! Playback data?
YES NO
Page 46
45
4) Use the UP/DOWN scroll button to select a trigger mode and
press the OK button.( Figure 5.21)
If data from previously tested vehicle is not erased, data from
current test will be stored in temporary cache.
5) Use the UP/DOWN scroll button to select a memory location
and press the OK button.( Figure 5.22)
The asterisk (*) icon on the screen indicates that there is a
previous recording in the memory location.
If you select a location marked with an asterisk (*) icon, a
message prompting to overwrite old recording is displayed.( Figure 5.23)
If you do not wish to proceed with overwriting old recording,
press the OK button; if you do not wish to overwrite it, press the ESC button, or use the LEFT/RIGHT button to select NO and press OK to pick another memory location.
6) Observe on-screen instructions. If Manual Trigger is selected, following screen shows:
(Figure 5.24)
If DTC Trigger is selected, following screen shows: (Figure
5.25)
7) Wait for DTC to trigger recording or press OK to start recording.
(Figure 5.26)
8) The scan tool keep recording PID data until user presses ESC
button, the selected memory location is full, or it completes recording. A message prompting to playback data shows on the screen. (Figure 5.27)
If you wish to playback recorded data, press the OK button; if
you do not wish to playback, press the ECS button, or use the LEFT/RIGHT button to select NO and press the OK button to return to Record Data menu.
Page 47
46
Playback Data
The Playback Data function allows viewing of previously stored
PID data.
1) To playback recorded data, use the UP/DOWN scroll button to
select Playback Data from Live Data menu and press the OK button. (Figure 5.12)
You are also allowed to playback recorded data immediately
after recording.
2) Use the UP/DOWN button to select the memory location
marked with an asterisk (*) icon.
Figure 5.28
If there is no recording in selected location, a message “Not
Supported or Stored No Data displays on the screen.
3) Use the UP/DOWN button to view recorded PIDs of each frame.
Figure 5.29
1 of 135 frame
6 DTC_CNT 0 FUELSYS1 OL FUELSYS2 N/A LOAD_PCT (%) 0.0 ?
ETC() -40
SHRTFT1(%) 99.2
Select Memory 3/3
Location #1 *
Location #2 ?
Location #3 *
Page 48
47
4) Use the LEFT/RIGHT button to view PIDs of next or previous
frames.
Figure 5.30
5.4 Viewing Freeze Frame Data
Freeze Frame Data allows the technician to view the vehicle‟s
operating parameters at the moment a DTC (Diagnostic Trouble Code) is detected. For example, the parameters may include engine speed (RPM), engine coolant temperature (ECT), or vehicle speed sensor (VSS) etc. This information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
1) To view freeze frame data, use the UP/DOWN scroll button to
select View Freeze Frame from Diagnostic Menu and press the OK button. (Figure 5.4)
2) Wait a few seconds while the scan tool validates the PID MAP.
3) If retrieved information covers more than one screen, use the
DOWN scroll button, as necessary, until all the data have been shown up.
6 of 135 frame
4 DTC_CNT 0 FUELSYS1 OL FUELSYS2 N/A
LOAD_PCT(%) 0.0 ?
ETC() -40 SHRTFT1(%) 99.2
Page 49
48
Figure 5.31
If there is no freeze frame data available, an advisory message
No freeze frame data stored!” shows on the display.
4) If you want to view full name of a PID, use the UP/DOWN
scroll button to select the PID, and press the HELP button.
Figure 5.32
5) Press ESC button to return to previous screen.
5.5 Retrieving I/M Readiness Status
I/M Readiness function is used to check the operations of the Emission System on OBD2 compliant vehicles. It is an excellent function to use prior to having a vehicle inspected for compliance to a state emissions program.
CAUTION - By clearing trouble codes you also clear the readiness status for the individual emission system readiness tests. In order to reset these monitors, the vehicle must be driven through a
…………View Freeze Frame 2 .
DTCFRZF P1633
FUELSYS1 OL
FUELSYS2 -­ LOAD_PCT (%) 0.0 ?
ECT() -40
SHRTFT1 (%) 99.2
……………… ..FUELSYS1……… …….
Fuel System 1 Status
Page 50
49
complete drive cycle with no trouble codes in memory. Times for reset vary depending on vehicle.
Some latest vehicle models may support two types of I/M Readiness tests:
A. Since DTCs Cleared - indicates status of the monitors since the
DTCs are erased.
B. This Drive Cycle - indicates status of monitors since the
beginning of the current drive cycle.
An I/M Readiness Status result of “NO” does not necessarily indicate that the vehicle being tested will fail the state I/M inspection. For some states, one or more such monitors may be allowed to be “Not Ready” to pass the emissions inspection.
OK -- Indicates that a particular monitor being checked has
completed its diagnostic testing.
INC -- Indicates that a particular monitor being checked has
not completed its diagnostic testing.
N/A -- The monitor is not supported on that vehicle. There are two ways to retrieve I/M readiness status.
A. Retrieve I/M Readiness status with One-Click I/M
Readiness Key
By simply pressing the One-Click I/M Readiness Key, you can retrieve the I/M readiness status. The screen will show as below. (Figure 5.33) According to different readiness status, the color LEDs will illuminate and different audio tones will be heard.
Page 51
50
Figure 5.33
OK -- Indicates that a particular monitor being checked
has completed its diagnostic testing.
INC -- Indicates that a particular monitor being checked
has not completed its diagnostic testing.
N/A -- The monitor is not supported on the vehicle.
The green, yellow and red LEDs provide a quick way to help you determine if a vehicle is ready for an Emission Test.
The LED and audio tone indications are interpreted as below:
LED Interpretation
1) GREEN LED – Indicates that engine systems are “OK” and
operating normally (the number of Monitors supported by the vehicle which have run and performed their self-diagnostic testing is in the allowed limit. MIL is off. ).There are no stored and pending DTCs. The vehicle is ready for an Emissions Test, and there is a good possibility that it can be certified.
2) YELLOW LED – With MIL off, there may be three possible
conditions to cause the yellow LED to light.
Page 52
51
If a Stored Diagnostic Trouble Code is causing the
Yellow LED to light, it is still possible that the vehicle will be allowed to be tested for emissions and certified.
If a Pending Diagnostic Trouble Code is causing the
Yellow LED to light, it is still possible that the vehicle will be allowed to be tested for emissions and certified.
If the illumination of the Yellow LED is being caused by
monitors that have not completed their diagnostic testing, then the issue of the vehicle being ready for an Emissions Test depends on the emissions regulations and laws of your local area.
NOTE: From the code retrieval procedure, determine the status of each Monitor. Take this information to an emissions professional to determine (based on your test results) if your vehicle is ready for an Emissions Test.
3) RED LED – Indicates there is a problem with one or more of
the vehicles system. A vehicle displaying a red LED is definitely not ready for an Emissions Test. The red LED is also an indication that there are DTCs present. The MIL lamp on the vehicles instrument panel will light steady. The problem that is causing the red LED to light must be repaired before an Emissions Test can be performed. It is also suggested that the vehicle be inspected/repaired before driving the vehicle further.
If the RED LED was obtained, there is a definite problem present in the system(s). In these cases, you have the following options:
Repair the vehicle yourself. If you are going to perform the
repairs yourself, proceed by reading the vehicle service manual and following all its procedures and recommendations.
Page 53
52
Take the vehicle to a professional to have it serviced. The
problem(s) causing the red LED to light must be repaired before the vehicle is ready for an Emissions Test.
Audio Tone Interpretation
The audio tone is configured according to the I/M Readiness Status. This function is invaluable when performing diagnostics and driving at the same time , or working in bright areas where LED illumination alone is not sufficient.
Different audio tone with different LED light indicates different I/M Readiness Status.
LED Light
Audio Tone
Beep Interval
Green LED
Two long beeps
5 seconds
Yellow LED
short, long, short beep
5 seconds
Red LED
Four short beeps
5 seconds
After you have read the information, press ESC to exit. The other buttons are disabled to prevent misoperation.
B. Retrieve I/M Readiness status in typical way
1) Use the UP/DOWN scroll button to select I/M Readiness from
Diagnostic Menu and press OK button. (Figure 5.4)
2) Wait a few seconds while the scan tool validates the PID MAP.
3) If the vehicle supports both types of tests, then both types will be
shown on the screen for selection.
Page 54
53
Figure 5.34
4) Use the UP/DOWN scroll button, as necessary, to view the status
of the MIL light (“ON” or “OFF) and the following monitors.
For spark ignition engines:
MIS -- Misfire Monitor FUEL -- Fuel System Monitor CCM -- Comprehensive Component Monitor EGR – EGR System Monitor O2S -- O2 Sensors Monitor CAT -- Catalyst Monitor EVAP -- Evaporative System Monitor HTR -- O2 Sensor Heater Monitor AIR -- Secondary Air Monitor HCAT -- Heated Catalyst Monitor
For compression ignition engines:
MIS -- Misfire Monitor FUEL -- Fuel System Monitor CCM -- Comprehensive Component Monitor EGR – EGR System Monitor HCCAT -- NMHC Catalyst Monitor NCAT -- NOx Aftertreatment Monitor BP -- Boost Pressure System Monitor EGS -- Exhaust Gas Sensor Monitor PM -- PM Filter Monitor
……………I/M Readiness 1/2.
Since DTCs Cleared
This Drive Cycle ?
Page 55
54
Figure 5.35
5) If the vehicle supports readiness test of This Drive Cycle, a
screen of the following displays:
Figure 5.36
6) The LEDs and audio tone corresponding to different monitor
status will be activated as below.
LED Light
Audio Tone
Beep Interval
Green LED
Two long beeps
2 minutes
Yellow LED
short, long, short beep
2 minutes
Red LED
Four short beeps
2 minutes
7) Use the UP/DOWN scroll button for more PIDs if additional
information is available on more than one page. Or use the LEFT/RIGHT scroll button to view PIDs in the previous/next page.
…………Since DTCs Cleared 1
MIL OFF
MIS N/A FUEL OK ? CCM OK CAT N/A HCAT N/A
…………..This Drive Cycle 1.
MIL OFF
MIS N/A FUEL OK ? CCM OK CAT N/A
HCAT N/A
Page 56
55
8) Press the ESC button to return to Diagnostic Menu.
5.6 Viewing Vehicle Information
The Vehicle Info. function enables retrieval of Vehicle Identification No. (VIN), Calibration ID Nos. (CINs), Calibration Verification Nos. (CVNs) and In-use Performance Tracking on 2000 and newer vehicles that support Mode 9.
1) Use UP/DOWN scroll button to select Vehicle Info. from the
Diagnostic Menu and press OK button. (Figure 5.4)
2) An advisory message comes up to remind you. Wait a few
seconds or press any key to continue.
Figure 5.37
3) Wait a few seconds while the scan tool reads vehicle information.
Figure 5.38
If the vehicle does not support this mode, a message shows on
the display warning that the mode is not supported.
Vehicle Info.
Reading info
- Please Wait -
Vehicle Info.
Turn key on
with engine off !
Press any key to con.
Page 57
56
4) From Vehicle Info. Menu, use the UP/DOWN scroll button to
select an available item to view and press the OK button.
Figure 5.39
5) View retrieved vehicle information on screen.
Figure 5.40
6) Press the ESC button to return to previous menu.
5.7 Code Breaker
Code breaker function is used to provide descriptions of DTCs and helpful tips to deal with DTCs. It is useful for technicians to find the root cause of trouble code faster, saving diagnosis and repair time.
1) Repeat steps in the Read Codes section to identify DTCs.
(Figure 5.41)
Vehicle Info. 3/3
Vehicle ID Number
Calibration ID
Cal. Verf. Number
?
Cal. Verf. Number
CVN1: BB BA A0 78
?
Page 58
57
Figure 5.41
1) Press the
? Help button to display Code Breaker menu.
Figure 5.42
2) Click on System Description and Quick Check to read the
code information, symptoms, specifications, data/sensor information, etc.
3) Click on General Notes to view helpful repair information
of DTCs.
4) To return to previous screen, press ESC button.
1/11
U0101 $07E8
Lost Communication
with TCM ?
Code Breaker 1/3
System Description
Quick Check General Notes
Page 59
58
6. Ready Test
This function can be used as a convenient readiness test tool by automotive technicians to determine if the tested vehicle is ready for an emission test. By visual and audible indication, you will learn a vehicles monitors readiness.
6.1 General Information
Repairs to the emissions-control systems of a 1996 or newer vehicle cause the vehicles computer (ECU) memory to be cleared. The vehicle must go through a drive cycle to allow the ECU to perform a series of tests to ensure that the repair was successful, and before a state mandated emissions test can be conducted. But how will you know when it is ready?
With this scan tool, you dont have to drive around endlessly and continuously coming back to the repair shop for retest if all required tests by the ECU are completed. And you could also do a quick check of the vehicle to determine if it is ready to receive an emission test without the hassle of connecting your vehicle to the analyzer or having to use a complicated scan tool.
In the following cases, this function is especially useful.
You bought a used car and the check engine light had been
cleared to mask potential problems.
You disconnected the battery for tune-ups and other engine
repairs, dead battery replacement, car radio installation and car alarm installation.
You used a scan tool to clear the DTCs. Your car has been sent to repair.
6.2 Ready test application
Page 60
59
The purpose of this function is to indicate which of the vehicles monitors have run and completed their diagnosis and testing, and which ones have not yet run and completed testing and diagnosis of their designated sections of the vehicles emission system. All data shows on one screen, which provides a simple profile of vehicle at a glance, saving diagnosis time and improving technician productivity.
Use the UP/DOWN scroll button and LEFT/RIGHT scroll
button to select Ready Test from Main Screen (Figure 6.1), and press the OK button.
Figure 6.1
As post-repair diagnostic tool
This function can be used (after the vehicle has done any emission-related repairs) to confirm that the repair has been performed successfully.
After repairs, some drive cycles are required to reset the monitoring systems. Drive cycles vary among vehicles and for each monitor in any particular vehicle.
Use the following procedure to check if the repair has been done correctly:
1) Connect the scan tool to the vehicles DLC and erase the DTC(s)
from the vehicle‟s computer memory. (see 5.2 erasing codes)
Page 61
60
2) After the erase procedure is performed, status of most monitors
will be changed. Leave the scan tool connected to the vehicle, and select Ready Test from Main Screen.
3) Keep on driving the car till the scan tool notifies you safely with
color LEDs and audible tone that the drive cycle has been completed and the vehicle is ready, eliminating drive cycle guesswork and confirming readiness status.
4) If the GREEN LED lights and two long beeps are heard, your
vehicle is ready and the repair work is confirmed.
5) If the RED LED lights, your vehicle is not ready and the repair
work is unsuccessful.
As pre-check diagnostic tool
Prior to having a vehicle inspected for compliance to a state emissions test, you could use this function to check the readiness status first by yourself.
1) While the scan tool connected to the vehicle, select Ready Test
from Main Screen. Drive the car till the scan tool notifies you safely with color LEDs and audible tone if your vehicle is ready to conduct state emission test.
2) If the GREEN LED lights and two long beeps are heard, your
vehicle is ready and there is a good possibility that it can be certified.
3) If the RED LED lights, your vehicle is not ready and must be
repaired before an emissions test can be performed.
IMPORTANT: If you are driving the vehicle to perform a drive cycle ALONE, please set the Status Beep On (see 3.8 System Setup). By listening to the beep, you will learn when the monitors have run and completed the diagnostic testing. NEVER try to drive and operate the scan tool at the same time!
Page 62
61
NOTE: This function reads off the real time data of emission-related monitoring systems readiness status. Once the scan tool has finished other operations, for example, clearing trouble codes, the I/M Readiness Monitor Status program resets status of all the monitors to INC condition. In order to set these monitors to a Ready status, the vehicle must be driven through a complete drive cycle. Times for reset vary depending on vehicle. Please refer to your vehicles service manual for drive cycle information.
NOTE: In this function, only ESC button is available. The other buttons are disabled to prevent misoperation.
6.3 LED and Tone Interpretation
Select Ready Test from the Main Screen and the screen shows as below, including applicable monitors status, MIL state, Ignition type, DTCs (stored one and pending one).
Figure 6.2
If the scan tool is idle, it will show the result immediately. If it is busy, it will wait till the current procedure finished. After viewing the status, press ESC button to exit.
OK -- Indicates that a particular monitor being checked
has completed its diagnostic testing.
Page 63
62
INC -- Indicates that a particular monitor being checked
has not completed its diagnostic testing.
N/A -- The monitor is not supported on the vehicle.
The LED and audio tone indications are interpreted as below:
LED Interpretation
The green and red LEDs provide an easy way to check if emission-related monitoring systems complete their self-diagnostic testing.
1) GREEN LED – Your vehicle is Ready. Indicates that engine
systems are OK and operating normally (the number of Monitors supported by the vehicle which have run and performed their self-diagnostic testing is in the allowed limit).
2) RED LEDYour vehicle is Not Ready. Indicates that the
number of Monitors supported by the vehicle which have run and performed their self-diagnostic testing is out of the allowed limit.
Audio Tone Interpretation
The audio tone could be configured according to the I/M Readiness Status. This function is invaluable when performing diagnostics and driving at the same time , or working in bright areas where LED illumination alone is not sufficient.
LED Light
Audio Tone
Beep Interval
Green LED
Two long beeps
2 minutes
Red LED
No beep
Page 64
63
7. Print Data
The Print Data function allows printing out diagnostic data recorded by the scan tool or customized test reports.
To print out retrieved data, you need the following tools:
AutoLink AL419 scan tool A PC or laptop with USB ports A USB cable
1) Install Maxi-LinkII applications through the included CD, or
downloading the applications from our website:
www.auteltech.com or our distributors site.
2) Connect the scanner to computer with the USB cable supplied.
3) Run Maxi-LinkII Tool Kit in your computer.
Figure 7.1
4) Use the UP/DOWN scroll button to select Print Data from
Main Menu in the scan tool, and press the OK button. (Figure
3.1)
5) Use the UP/DOWN scroll button to select the desired item to
print from Print Data menu.
Page 65
64
Figure 7.2
To print all retrieved data, use the UP/DOWN scroll button to
select Print All Data from Print Data menu.
6) Press the OK button to upload data to the computer.
7) In the Maxi-Link Tool Kit, you could edit, delete, copy and print
the data in the textbox by selecting the icons on the upper right of window.
Print data.
Delete data.
Copy data.
Edit data.
NOTE: Data stored in a language different from current system settings of the scan tool will not be printable. Please adjust language settings before printing. A reminder would pop up under such circumstances.
Print Data 1/9
Stored Codes
Pending Codes Live Data ?
Freeze Frame I/M Readiness O2 Sensor Test Print All Data
Page 66
65
8. Warranty and Service
8.1 Limited One Year Warranty
Autel warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one (1) year from the date of the original purchase, subject to the following terms and conditions:
1) The sole responsibility of Autel under the Warranty is limited to
either the repair or, at the option of Autel, replacement of the scan tool at no charge with Proof of Purchase. The sales receipt may be used for this purpose.
2) This warranty does not apply to damages caused by improper use,
accident, flood, lightning, or if the product was altered or repaired by anyone other than the Manufacturer‟s Service Center.
3) Autel shall not be liable for any incidental or consequential
damages arising from the use, misuse, or mounting of the scan tool. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
4) All information in this manual is based on the latest information
available at the time of publication and no warranty can be made for its accuracy or completeness. Autel reserves the right to make changes at any time without notice.
8.2 Service Procedures
If you have any questions, please contact your local store, distributor
or visit our website at www.auteltech.com.
If it becomes necessary to return the scan tool for repair, contact your
local distributor for more information.
Loading...