Autec CRPNL055 User Manual

LIUCRP000_eng-00

In󰄋ruction Manual for the use and the maintenance
of the Radio Remote Control

Original in󰘵ructions

Part D: CRP Receiving Unit

DYNAMIC+P SERIES

THIS PART OF THE MANUAL CONSISTS OF Part D - Information, in󰄋ructions and warnings
for the CRP Receiving Unit. The Manual consi󰄋s of Part A – General, Part B – Conformity
and Frequencies, Part C – Transmitting Unit, Part D – Receiving Unit, Part E – Battery
and Battery Charger, plus the Technical Data Sheet.

THIS MANUAL, INCLUDING ALL PARTS THEREOF, AND ALL INSTRUCTIONS CONTAINED
HEREIN, MUST BE READ CAREFULLY AND UNDERSTOOD BEFORE INSTALLING, USING,
MAINTAINING OR REPAIRING THE AUTEC RADIO REMOTE CONTROL.

FAILURE TO READ AND COMPLY WITH ALL APPLICABLE WARNINGS AND INSTRUCTIONS
OR ANY ONE OF THE LIMITATIONS NOTED IN THIS MANUAL CAN RESULT IN SERIOUS
BODILY INJURY OR DEATH, AND/OR PROPERTY DAMAGE.

THE AUTEC RADIO REMOTE CONTROL IS NOT A STANDALONE PRODUCT AND IS
INTENDED ONLY AS A COMPONENT ON A MACHINE:

- ON WHICH AND WHERE THE USE OF A RADIO REMOTE CONTROL IS APPROPRIATE,

- THAT CAN BE OPERATED SAFELY AND IN ACCORDANCE WITH ALL APPLICABLE
LAWS, REGULATIONS AND STANDARDS BY SUCH REMOTE CONTROL.

ACCORDINGLY, IT IS THE RESPONSIBILITY OF THE MACHINE MANUFACTURER ON
WHICH THE AUTEC REMOTE CONTROL IS INTENDED TO BE INSTALLED, to perform
an in-depth and accurate risk assessment to determine if the Autec Radio Remote Control
is suitable for operating a Machine in conditions of safety and operational effectiveness,
taking into account the conditions of use, the intended uses and the reasonably
foreseeable incorrect ones, so that the in󰄋allation, maintenance and use of the Autec
Radio Remote Control, and all its components, are performed only and entirely in
compliance with this Manual and in accordance with all local regulations, safety 󰄋andards
and regulations (referred to herein as "Laws, Regulations and Standards").

With reference to the USA market the Laws, Regulations and Standards include all safety
rules and regulations of the Occupational Safety & Health Admini󰄋ration (OSHA) (http://
www.osha.gov), all federal, 󰄋ate and local laws, regulations and building and electrical
codes, and all applicable 󰄋andards, including but not limited to ANSI Standards.

LIUCRP000_eng-00AUTEC

It is also the responsibility of the Manufacturer and of the design professionals of the
Machine on which the Autec Radio Remote Control is to be in󰄋alled and used to be certain
that the 󰄋ructure, condition, organization and markings of the Machine as in󰄋alled at
the facility is appropriate for and will allow for the safe and reliable use and control of
the Machine through the Autec Radio Remote Control interface.

IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
DESIGN PROFESSIONALS, that the in󰄋allation, maintenance and operation of the Autec
Radio Remote Control and all of its components are done solely and completely in
accordance with this Manual, and with all applicable Laws, Regulations and Standards,
even local. It is also the responsibility of the Manufacturer of the Machine on which the
Autec Radio Remote Control is to be in󰄋alled and used, and their design professionals,
to be certain that the 󰄋ructure, condition, organization and markings of the Machine as
in󰄋alled at the facility is appropriate for and will allow for the safe and reliable use and
control of the Machine through the Autec Radio Remote Control interface.

ONLY QUALIFIED AND PROPERLY TRAINED PERSONNEL SHOULD BE PERMITTED TO
OPERATE OR USE THE AUTEC RADIO REMOTE CONTROL AND THE MACHINE OPERATED
BY OR THROUGH THE AUTEC RADIO REMOTE CONTROL. ONLY QUALIFIED AND
PROPERLY TRAINED PERSONNEL SHOULD BE PERMITTED TO BE IN THE VICINITY OF
MACHINE OPERATED BY OR THROUGH THE AUTEC RADIO REMOTE CONTROL.

FAILURE TO PROPERLY INSTALL, OPERATE, MAINTAIN AND SERVICE THE AUTEC
RADIO REMOTE CONTROL CAN RESULT IN SERIOUS BODILY INJURY OR DEATH AND/
OR PROPERTY DAMAGE. Refer to this Manual and each of its Parts for further assi󰄋ance
or contact Autec. Autec is not responsible for and shall not be held liable for any in󰄋allation
of the Autec Radio Remote Control not performed by Autec or for any use of the Autec
Radio Remote Control not in complete compliance with, and/or not maintained in complete
compliance with, all Autec in󰄋ructions and warnings and all applicable Laws, Regulations
and Standards, even local.

Autec is not responsible for and shall not be held liable for any alteration or modification
of the Autec Radio Remote Control, or the use of non-Autec components or products
used with or incorporated into the Autec Radio Remote Control.

IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
DESIGN PROFESSIONALS, to be certain that the Autec Radio Remote Control is properly
maintained and serviced at all times in compliance with all Autec in󰄋ructions and
warnings, and with all applicable Laws, Regulations and Standards, even local.

LIUCRP000_eng-00 AUTEC

IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
OFFICERS, MANAGERS AND SUPERVISORS, to be certain that all Users of the Autec
Radio Remote Control and that all Persons who are or will be working with or near the
Machine operated by or through the Autec Radio Remote Control are fully and properly
educated and trained by qualified Personnel in the proper and safe use of the Autec Radio
Remote Control and of the Machine, including without limitation complete familiarity
with and under󰄋anding of Autec warnings and in󰄋ructions, and all applicable Laws,
Regulations and Standards, even local, and that such Users and other Persons do in fact
at all times operate or work with the Autec Radio Remote Control safely and ONLY in
compliance with Autec in󰄋ructions and warnings and with all applicable Laws, Regulations
and Standards, even local. FAILURE TO DO SO CAN RESULT IN SERIOUS BODILY INJURY
OR DEATH AND/OR PROPERTY DAMAGE.

IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
OFFICERS, MANAGERS AND SUPERVISORS, to be certain that the areas in which the
Machine operated by or through the Autec Radio Remote Control is located and operates
are clearly delineated and marked in accordance with all Autec warnings and in󰄋ructions,
and all applicable Laws, Regulations and Standards, even local, and otherwise sufficient
to alert and warn ALL PERSONS that the Machine is operated by or through a Radio
Remote Control, and prohibiting any unauthorized access thereto. FAILURE TO DO SO
CAN RESULT IN SERIOUS BODILY INJURY OR DEATH AND/OR PROPERTY DAMAGE.

FAILURE TO OPERATE THE AUTEC RADIO REMOTE CONTROL SAFELY AND IN
COMPLIANCE WITH AUTEC INSTRUCTIONS AND WARNINGS AND WITH APPLICABLE
LAWS, REGULATIONS AND STANDARDS, EVEN LOCAL, AND/OR PERMITTING USERS
OR OTHER PERSONS NOT PROPERLY TRAINED IN THE SAFE AND PROPER USE OF
THE SYSTEM, OR THE MACHINE ON WHICH IT IS INSTALLED, CAN RESULT IN SERIOUS
BODILY INJURY OR DEATH AND/OR PROPERTY DAMAGE.

LIUCRP000_eng-00AUTEC

6

INDEX

1 Information on the use of in󰄋ructions ..................................................................... 7

1.1 Structure of the In󰘵ruction Manual ...................................................................... 7

1.2 Caption and terminology ..................................................................................... 9

1.3 Symbols ............................................................................................................. 9

1.4 To whom the in󰘵ructions are addressed ............................................................ 10

1.5 In󰘵ruction 󰘵orage ............................................................................................ 10

1.6 Intellectual property .......................................................................................... 10

2 Brief product presentation ..................................................................................... 11

2.1 Series, Radio Remote Control and Unit ............................................................. 11

2.2 Conformity with 󰘵andards ................................................................................. 11

2.3 Contacts and useful addresses ......................................................................... 11

2.4 Warranty .......................................................................................................... 11

2.5 Technical assi󰘵ance and spare parts ................................................................ 11

3 Description of the Receiving Unit ........................................................................... 12

4 Technical data ......................................................................................................... 14

5 Technical Data Sheet .............................................................................................. 16

6 Plates ....................................................................................................................... 16

7 Light signals ............................................................................................................ 17

7.1 Seven-segment display .................................................................................... 17

7.2 POWER LED .................................................................................................... 18

7.3 STATUS LED ................................................................................................... 19

7.4 RUN LED .......................................................................................................... 19

7.5 ERR LED .......................................................................................................... 19

7.6 SETUP LED ...................................................................................................... 20

8 In󰄋alling the Receiving Unit ................................................................................... 21

8.1 Warnings for the In󰘵aller .................................................................................. 21

8.2 Positioning the antenna .................................................................................... 22

8.3 Wiring ............................................................................................................... 22

8.4 At end of in󰘵allation .......................................................................................... 23

9 Maintenance ............................................................................................................ 24

10 Malfunction signalled by the Receiving Unit .......................................................... 25

11 Decommissioning and disposal ............................................................................. 27

LIUCRP000_eng-00 AUTEC

7

1 Information on the use of in󰄋ructions

Before reading this part of the Manual, you mu󰘵 read and under󰘵and the general
part (Part A) of the Manual provided with the Radio Remote Control.

1.1 Structure of the In󰄋ruction Manual

The Manual for the use and maintenance of Autec Radio Remote Controls consists in di󰘯erent
parts, that altogether form the Manual; the Manual must be read carefully, understood and
applied by the Radio Remote Control's Owner, User and by all those Persons that, for any
reasons, may operate with the Radio Remote Control or with the Machine where it is installed.
The following table describes the structure of the Instruction Manual for the use and the
maintenance of the Radio Remote Control.

Part Title Contents

- General information regarding the series,

- directions for risk assessment of the "Machine+Radio Remote
Control" sy󰘵em,

A General part

Conformity and

B

frequencies

C Transmitting Unit

D Receiving Unit

Battery and battery

E

charger

- warnings for in󰘵allation of the Radio Remote Control,

- warnings for use and maintenance of the Radio Remote
Control,

- in󰘵ructions for correct transportation and 󰘵orage of Radio
Remote Control.

- Operating frequency bands of the Radio Remote Control,

- conformity and law references of the Radio Remote Control.

Description and in󰘵ructions concerning the Transmitting Unit,
including:

- description of operation,

- commands,

- light signals,

- malfunctions,

- additional in󰘵ructions to the general part.

Description and in󰘵ructions concerning the Receiving Unit,
including:

- description of operation,

- light signals,

- malfunctions,

- additional in󰘵ructions to the general part.

Description, warnings and in󰘵ructions concerning batteries and
battery chargers, including:

- description of operation,

- light signals,

- malfunctions,

- in󰘵ructions for the User.

LIUCRP000_eng-00AUTEC

8

Usage and maintenance in󰘵ructions are supplemented by the Radio Remote Control's Technical
Data Sheet, that:

- Describes the Transmitting Unit's con󰘰guration

- Indicates the relation between commands sent by the Transmitting Unit and those available on

the Receiving Unit.

Usage and maintenance instruction as a whole are to be considered as an integral part both
of the Autec Radio Remote Control and of the Machine, system, device or Machinery system
where the Radio Remote Control is installed.
The Manufacturer of the Machine on which the Autec Radio Remote Control is in󰘵alled, and
the Owner and User of the Machine, mu󰘵 make sure that the In󰘵ruction Manual and all of its
parts are included in the In󰘵ruction Manual of the Machine.

The CD attached to each In󰘵ruction Manual includes the translations of the Manual.

Act as follows to identify the single Manual parts in the relevant language in the CD:

- Choose the desired language

- Select the single parts of the Manual: refer to the code name provided on the cover of each

part.

XXXXXXXXX_language-XX

Instruction Manual for the use and the
maintenance of the Radio Remote Control

Original instructions

XXXXXXXXX_language-XX

Part X: XXXXXXXXXXXXXXXXXXXXXXXXXXXXX

XX SERIES

LIUCRP000_eng-00 AUTEC

9

1.2 Caption and terminology

Contact Autec if any of the in󰘵ructions, symbols, warnings or images are not clear
and under󰘵andable, or if you have doubts or que󰘵ions.

In this part of the Manual, the terms li󰘵ed below have the same meaning explained in the
corresponding paragraph of the general part (Part A):

- Unit

- Radio Remote Control

- Transmitting Unit

- Receiving Unit

- Machine

- Manufacturer

- In󰄋aller

- User

- Maintenance Technician

- Manual or In󰄋ruction Manual

- In󰄋allation manual

- Person

- Owner

Functions indicated for the Manufacturer, the In󰘵aller, the User and the Maintenance Technician
may be performed by a single Person, if he/she has the needed competence and undertakes
the resulting responsibilities. Each Person mu󰘵 be aware of the in󰘵ructions contained in the
Manual, depending on the activity they carry out.
For example, if a Manufacturer is also the In󰘵aller, and/or Maintenance Technician, he mu󰘵
also know and follow the in󰘵ructions specifically addressed to those Persons. The same applies,
for example, if a User is also the Manufacturer and/or the In󰘵aller.

1.3 Symbols

This symbol identifies the parts of text in the Manual that mu󰘵 be read with special
attention.

This symbol identifies the parts of text in the Manual containing warnings,
information and/or in󰄋ructions that are particularly relevant with regards to
safety; failure in under󰄋anding them may cause hazards for People and/or
property.

LIUCRP000_eng-00AUTEC