Australian Monitor ICON CP User Manual

INSTALLATION AND OPERATION MANUAL

ICON-CP

IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION

Read these instructions.1.

Keep these instructions.2.

Heed all warnings.3.

Follow all instructions.4.

Do not use this apparatus near water.5.

Clean only with dry cloth.6.

Do not block any ventilation openings. Install in accordance with the 7.
manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, 8.
stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. 9.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly 10.
at plugs, convenience receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by the manufacturer.11.

Use only with the cart, stand, tripod, bracket, or table specified by the 12.
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when 13.
unused for long periods of time.

Refer all servicing to qualified service personnel. 14.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.

This appliance shall not be exposed to dripping or splashing water and 15.
that no object fi lled with liquid such as vases shall be placed on the
apparatus.

Plug this apparatus to the proper wall outlet and make the plug to be 16.
disconnected readily operable.

Main plug is used as disconnected device and it should remain readily 17.
operable during intended use. In order to disconnect the apparatus from
the mains completely, the mains plug should be disconnected from the
mains socket outlet completely.

WARNING:18. To reduce the risk of fi re or electric shock, do not expose this
apparatus to rain or moisture.

An appliance with a protective earth terminal should be connected to a 19.
mains outlet with a protective earth connection.

LISEZ ces instructions.1.

Tenez ces instructions.2.

Notez tous les avertissements.3.

Suivez toutes les avertissements.4.

N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.).5.

Nettoyez seulement avec une étoffe sèche.6.

Ne bloquez aucuns troux de ventilation. Installez en accord avec 7.
les instructions du manufacturier.

N’installez près aucunes sources de chaleur comme radiateurs, registres 8.
de chaleur, fours ou les autres équipements (y compris amplifi cateurs)
qui produisent la chaleur.

Ne défaites pas le but de sécurité de la fi che polarisée ou base-type. 9.
Une fi che polarisée a deux tranchants avec un plus large que l’autre.
Une fi che de base type a deux a deux tranchants et une troisième
pointe de base, le tranchant large ou la troisième pointe est fourni
pour votre sécurité. Si la fi che donnée ne conforme pas votre prise
de contact, consultez un électricien pour remplacement de la prise
de contact obsolète.

Protegez le cordon de secteur contre être marchée dessus ou pincez 10.
en particulier aux fi ches, aux douilles de convenance, et au point où ils
sortent de l’appareil.

Seulement utilisez attachements/accessoires spécifi és par le 11.
manufacturier.

Utilisez seulement avec un chariot, un stand, un trépied, un support 12.
ou une table indiquée par le manufacturier, ou vendue avec l’appareil.
Quand un chariot est utilisé, faites attention en déplaçant la combinaison
d’appareil/chariot pour éviter de se déséquilibrer.

Arrachez la fi che du dispositif durant éclair et orage ou 13.
quand pas utilisé pour longues périodes de temps.

Référez au personnel qualifi é de service pour toutes 14.
réparations. La réparation est donnée quand le système
a été endommagé à n’importe façon, par exemple un fi l ou une fi che
endommagé(e) de la source d’alimentation. Avoir été exposé à pluie ou
humidité, n’opère pas normalement, ou avoir été tombé.

L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures 15.
et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé
sur l’objet.

Branchez l’appareil à une source appropriée et faire que la prise à 16.
débrancher soit facilement accessible.

La prise du secteur ne doit pas être obstruée ou doit être facilement 17.
accessible pendant son utilisation. Pour être complètement déconnecté
de l’alimentation d’entrée, la prise doit être débranchée du secteur.

AVERTISSEMENT: 18. Pour éviter le risque d’incendie ou de chocs électriques,
ne pas exposer cet appareil à la pluie ou à l’humidité.

Un appareil avec la borne de terre de protection doit être connecté au 19.
secteur avec la connexiion de terre de protection.

PAGE 2

ICON-CP MANUAL

INTRODUCTION AND CONTENTS

ICON-CP

The ICON control panel is both elegant and ergonomic to suit
today’s modern installations.

The ICON CP controls a number of Australian Monitor products &
will also be compatible with a number of new products making the
unit fl exible and future proof.

The ICON control panel is programmable to allow for a host of
confi gurations and control options all from the one control panel.

INTRODUCTION 3

ICON-CP AND REVOLUTION SERIES 4

ICON-CP AND AMD100-200 5

ICON-CP AND IN600 6

DIMENSIONS 7

Revision 1.2 August 2010

WARNING!

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH

AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES

CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT, FULLY INSERT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning fl ash with arrowhead symbol,

within an equilateral triangle, is intended

to alert the user to the presence of
uninsulated “dangerous voltage” within
the product’s enclosure that may be of

suffi cient magnitude to constitute a risk

of electric shock to persons.

WARNING: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

ICON-CP MANUAL

Rating plate and caution marking are marked on the back enclosure of the apparatus

PAGE 3

ICON-CP AND REVOLUTION SERIES

ICON-CP Control Panel

The Revolution series control panels (ICON-CP) have two banks of DIP switches
on the rear of the control panel. The fi rst bank of switches labeled SW1 allows
the user to address the panel for RS485 communications. The second bank of
switches allows the user to set up the LED functions for the remote panel.

SW1:

RS485 addresses 1-240 are allowed. With any other address the unit will blink
its error LEDs.

ABC

SW2 Func

fail or be broken it could simply be swapped out with a unit set to the same
address. All control panels are constantly polling the RS485 network for status.
This will allow the user to update settings via 3rd party, other control panels or
the software GUI and have all panels constantly up to date.

Each RS485 port on the Revolution series allows you to run up to 20 control
panels to a maximum distance of 500 metres. With each unit featuring two
RS485 ports, this allows the AV Revolution to run up to 40 ICON-CP’s on two
separate 500m runs. The 500m limitation of the control panels is due to power
loss over distance and not RS485 limitations therefore if lengths longer than
500m are required you need to inject power locally for greater distances.

D

1248163264

128

SW1 Address

SW2

A: ON = LED brightness varies based on ambient light, OFF = Fixed Brightness

B: ON = Low brightness (if switch A is on fi xed brightnes mode), OFF = Normal
Brightness

C: Unused on Revolution series

D: Unused on Revolution series

The ICON-CP control panels do not hold any project data so if a panel was to

PAGE 4

ICON-CP MANUAL

The ICON-CP can be used to control certain functions of the AMD100/200.

The set up the control panel all you need to do is address the panel on SW1.
Switch 1-8 represent a binary address. For example to address it to ID1 all you
need to do is have number 1 on, to address it to 3 have switch 1 and 2 on.

SW2 C and D do not do anything, A and B adjust the LED settings of the panel.
With switch A high ambient light adjustment will be turned on. With switch B on,
low brightness mode will be activated. Only one switch should be up at a time.

ID 1: (Switch 1 On)

In this mode the fi rst 5 buttons act as a source select (1-4 and off)

The 6th button acts as a mute control

Buttons 7 and 8 are volume up and volume down for the BGM source

NOTE:
BGM Off deselects all the BGM input.

BGM Mute toggles and maintains the selected BGM source for easy unmuting.

ICON-CP AND AMD100-200

1. BGM 1

2. BGM 2

3. BGM 3

4. BGM 4

5. BGM Off

6. BGM Mute

7. BGM Vol +

8. BGM Vol -

ID 2: (Switch 2 On)

In this mode the panel acts as 6 individual volume controls.

The fi rst 6 buttons pick the volume you want to control and the bottom two buttons are
volume up and volume down.

ID 3: (Switch 1 and 2 On)

This mode is the same as two but controls different sources.
Note, this is will work on AMD200 only.

1. Mic\Line 1

2. Mic\Line 2

3. Mic\Line 3

4. Mic\Line 4

5. BGM

6. Master

+ Volume

- Volume

1. Mic\Line 5

2. Mic\Line 6

3. Mic\Line 7

4. Mic\Line 8

5. BGM

ICON-CP MANUAL

6. Master

+ Volume

- Volume

PAGE 5

ICON-CP AND IN600

With the ICON-CP’s DIP switch bank 2(FUNC) set with D on the ICON-CP will control the
AMAV IN600.

The control parameters are fi xed to three different confi gurations. These are:

1. Source 1 (DVD1)

2. Source 2 (DVD2)

Address ID 1: (Switch 1 On)

With this setting you get control over selection of the sources and also volume control
of the source mixer. When a source is selected after already being active the unit will
switch the source to “Off”

Address ID 2: (Switch 2 On)

With this setting you have control over turning the projector on and off. You can also turn
each microphone on by triggering its mute control. The volume control will control the
mic mixer level on the unit.

Address ID 3: (Switch 1 and 2 On)

With this setting selected you have the exact same controls as ID2 except the
microphone mute controls are inversed so that the active state will have the
microphone off.

Powering the ICON-CP

The ICON-CP remote panels will need to be externally powered when being used with
the IN600. As these units have RJ45 looped in and outs we now provide a 24V DC
power injector that simply has a data in and a P+Data out. It is recommended that this
unit be placed close to the ICON-CP, all you need to do is run from the IN600 into the
power injector then out to your run of remote panels.

3. Source 3 (AUX1)

4. Source 4 (AUX2)

5. Source 5 (PC1)

6. Source 6 (PC2)

7. Source Volume Up

8. Source Volume Down

Address ID 1: (Switch 1 On)

1. Projector On

2. Projector Off

3. Mic 1 On

4. Mic 2 On

5. Mic 3 On

6. Mic 4 On

7. Mic Volume Up

Connecting to the IN600

When wiring the ICON-CP panels we suggest simply using premade cables if possible
or if terminating your own to follow one standard the whole way that will allow your
connections to be pin to pin from the start to the end.

The IN600 has a terminal block for the RS485 bus. The pin out needed to connect the
ICON-CP to the IN600 is below:

Data line A = Pin 3 of the ICON-CP

Data line B = Pin 6 of the ICON-CP

Gnd line = Pin 2 of the ICON-CP

White/Green 1

Green 2

Shown with

locking clip

facing

White/Orange 3

Blue 4

White/Blue 5

Orange 6

White/Brown 7

Brown 8

CABLE

8. Mic Volume Down

Address ID 2: (Switch 2 On)

1. Projector On

2. Projector Off

3. Mic 1 Off

4. Mic 2 Off

5. Mic 3 Off

6. Mic 4 Off

7. Mic Volume Up

8. Mic Volume Down

Address ID 3: (Switch 1 and 2 On)

PAGE 6

568A configuration

ICON-CP MANUAL

DIMENSIONS

ICON-CP MANUAL

PAGE 7

ENGINEERED BY AUSTRALIAN MONITOR

Address: 1 Clyde Street, Silverwater, Sydney NSW 2128 Australia. Private Bag 149, Silverwater NSW 1811 ABN 78 001 345 482
Website: www.australianmonitor.com.au International enquiries email: [e-mail]

DISTRIBUTED IN AUSTRALIA AND NEW ZEALAND BY HILLS SVL www.hillssvl.com.au

NSW QLD ACT WA VIC SA NZ
P: 02 9647 1411 P: 07 3852 1312 P: 02 6260 4544 P: 08 9204 0200 P: 03 9890 7477 P: 08 8408 8300 P: 09 415 9426
E: [e-mail] E: [e-mail] E: [e-mail] E: [e-mail] E: [e-mail] E: [e-mail] E: [e-mail]