Australian Monitor. AMIS26 Brochure

Description

The Australian Monitor Installation Series AMIS26 is a high quality 2 input, 6 output

distribution amplifier. The AMIS26 provides a low noise, feature packed, signal

routing solution to cover a wide range of installation needs, at a contractor

friendly price.

AMIS26

Distribution Amplifier

Inputs

The AMIS26’s 2 inputs can be balanced or unbalanced and each input’s sensitivity

can be switched between Mic and Line level. Each of the AMIS26’s inputs is

individually assignable to any of the 6 outputs via front panel DIP switches

Outputs

The 6 outputs can again be balanced or unbalanced and feature up to -60dB of

attenuation so they can be run as any combination of line level or mic level outputs.

Controls

Input Level: The input level controls are screw diver adjustable trim pots. The input

level can boost or cut the input signal by up to 15dB.

Input Assign Switches: The recessed DIP switches assign either input A or B to a

desired output.

Output Level: The output level controls are screw driver adjustable trim pots. This

level control attenuates the output level, with a range from -60dB at “Minimum”

position, to 0dBat “Maximum” position.

Output Level DIP switch: This switch will change the output sensitivity of the

desired output from Mic to line level.

24 VDC Phantom Power is also individually switchable per input

Metering

Input Level Meter: These 4 segment LED meters show the strength of each of the

AMIS26’s input signals. LED segments are calibrated to the following level markings

and show the following colours -20dBu (green), -10dBu (green), 0dBu (yellow),

+10dBu (red).

Phantom Power

-24 VDC Phantom power is also individually switchable per input.

Power Input 24 VDC (regulated); 12VA max.

Output Mic/Line Switch 28dB

Noise -89dB

Frequency Response (0dB/-3dB) 10Hz - 50kHz

Total Harmonic Distortion Line In (XLR/RCA) 0.02%; Mic In (XLR) 0.1%

Crosstalk Better than 80dB

Phantom Power 24VDC

Input Sensitivity Line (XLR) 775mV (0dB); Mic (XLR) 10mV (-37dB);

Line (RCA) 775mV (0dB)

Dimensions Dimensions: 44.0 x 482.0 x 168.0 (H x W x D) mm

Weight Net 2.5 kg (5.5 lb), Shipping 3.0 kg (6.6 lb)

• All measurements done with levels set In/Out at 0dB;

• All measurements referenced to 0dBu (0.775mV)

ARCHITECTURAL AND ENGINEERING SPECIFICATIONS

The distribution amplifier shall be a high quality two input, six output distribution

1RU device. The unit will have two inputs which can be balanced or unbalanced

and each input’s sensitivity can be switched between Mic and Line level via dip

switches. Additionally these front panel dip switches will allow any of the inputs to be

routed to any of the six outputs. The units shall provide a four segment LED level

meter per input.

The unit shall provide 24 VDC Phantom power which is to be individually switchable

per input.

The units outputs shall be balanced or unbalanced and feature up to -60dB of atten-

uation so that they can be run as any combination of line level or mic level outputs.

The distribution amplifier shall be an Australian Monitor Installation Series AMIS26.

Engineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (

NSW Tel: [phone] Fax: [phone] VIC Tel: [phone] Fax: [phone] QLD Tel: [phone] Fax: [phone] WA Tel: [phone] Fax: [phone]

SA Tel: [phone] Fax: [phone] NZ Tel: [phone] Fax: [phone] Export Enquiries: [e-mail]

ABN 78 001 345 482), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia

Website: www.australianmonitor.com.au