Global LCD Panel Exchange Center
Product Description:
AUO Model Name: T315XW01 V8
Customer Part No/Project Name:
www.panelook.com
Customer Signature Date AUO Date
Approved By: Frank Ko
Reviewed By: HongJye Hong
Prepared By: William Wu
Please return one copy with your signature and comments for
our confirmation.
AU Optronics Corporation
Tel: +886-3-563-2899
Fax: +886-3-566-5233
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 1/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specifications
31.5” WXGA Color TFT-LCD Module
Model Name: T315XW01 V8
( ) Preliminary Specifications
(*) Final Specifications
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 2/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
No
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION1
www.panelook.com
Contents
ABSOLUTE MAXIMUM RATINGS2
ELECTRICAL SPECIFICATIONS3
ELECTRICAL CHARACTREISTICS3-1
INTERFACE CONNECTIONS3-2
SIGNAL TIMING S PE CIFICATIONS3-3
SIGNAL TIMING W AVEFORMS3-4
COLOR INPUT DATA REFERNECE3-5
POWER SEQUENCE3-6
OPTICAL SFECIFICATIONS4
MECHAN ICAL CH AR AC TE RIS TICS5
RELIABLITY6
INTERNATIONAL STANDARDS7
SAFETY7-1
EMC7-2
Packing8
PRECAUTIONS9
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 3/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Version Date No Old Description New Description Remark
1.0 2005/5/17 All All First Issued
www.panelook.com
Record of Revision
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 4/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
1. General Description
This specification applies to the 31.51 inch Color TFT-LCD Module T315XW01 V8. This
LCD module has a TFT active matrix type liquid crystal panel 1366x768 pixels, and diagonal
size of 31.51 inch. This module supports 1366x768 XGA-WIDE mode (Non-interlace).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in
vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit
gray scale signal for each dot.
The T315XW01 V8 has been designed to apply the 8-bit 1 channel LVDS interface method.
It is intended to support displays where high brightness, wide viewing angle, high color
saturation, and high color depth are very important.
www.panelook.com
* General Information
Items Specification Unit Note
Active Screen Size 31.51 inches
Display Area 697.68 (H) x 392.26(V) mm
Outline Dimension 760.0(H) x 450.0(V) x 47(D) mm With inverter
Driver Element a-Si TFT active matrix
Display Colors 16.7M Colors
Number of Pixels 1366 x 768 Pixel
Pixel Pitch 0.51075 mm
Pixel Arrangement RGB vertical stripe
Display Mode Normally Black
Surface Treatment AG, 3H
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 5/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause permanent damage to the
unit.
Item Symbol Min Max Unit Conditions
Logic/LCD Drive Voltage VDD -0.3 5.5 [Volt] Note 1
Input Voltage of Signal Vin -0.3 3.6 [Volt] Note 1
www.panelook.com
BLU Input Voltage VDDB -0.3 27 [Volt] Note 1
BLU Brightness Control Voltage BLON -0.3 7.0 [Volt] Note 1
Operating Temperature TOP 0 +50 [oC] Note 2
Operating Humidity HOP 10 90 [%RH] Note 2
Storage Temperature TST -20 +60 [oC] Note 2
Storage Humidity HST 10 90 [%RH] Note 2
Note 1 : Duration = 50msec
Note 2 : Maximum Wet-Bulb should be 39 and No condensation.
Note 3 :The relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. At
temperatures greater than 40, the wet bulb temperature must not exceed 39.
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 6/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3. Electrical Specification
The T315XW01 V2 requires two power inputs. One is employed to power the LCD electronics and to drive the
TFT array and liquid crystal. The second input power for the BLU, is to power inverter..
3-1 Electrical Characteristics
www.panelook.com
ValuesParameter Symbol
Min Typ Max
LCD:
Power Supply Input Voltage Vcc 4.5 5.0 5.5 Vdc
Power Supply Input Current Icc - 1.5 1.8 A 1
Power Consumption Pc - 7.5 9 Watt 1
Inrush Current I
Backlight Power Consumption Pbl 115 132 Watt
Life Time 60,000 Hours 3
Note :
1. Vcc=5.0V,
2. Duration = 1
3. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by
the characteristics of the DC-AC Inverter. So all the parameters of an inverter should be carefully
designed so as not to produce too much leakage current from high-voltage output of the inverter. When
you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the
lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly
should be operated in the same condition as installed in your instrument.
4. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape,
TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current
occurs between lamp wire and conducting tape.
5. The relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. At
temperatures greater than 40, the wet bulb temperature must not exceed 39. When operate at low
temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced.
=vf 60Hz, fCLK=81.5Mhz , 25,
ms
RUSH
2.5 - 4.5 Apeak 2
Unit Notes
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 7/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3-2 Interface Connections
- LCD connector (CN3): JAE FI-E30S or equivalent
- LVDS Transmitter: SN75LVDS83(Texas Instruments) or equivalent
Note:
All GND (ground) pins should be connected together and should also be connected to the LCD’s metal
1.
frame. All Vcc (power input) pins should be connected together.
No Signal No Signal
1 N.C. 16 GND
2 N.C. 17 RIN3-
3 N.C. 18 RIN3+
www.panelook.com
4GND19GND
5 RIN0- 20 Reserved.
6 RIN0+ 21 LVDS Option
7 GND 22 Rotate Option
8 RIN1- 23 GND
9 RIN1+ 24 GND
10 GND 25 GND
11 RIN2- 26 Vdd (+5V)
12 RIN2+ 27 Vdd (+5V)
13 GND 28 Vdd (+5V)
14 RxCLK- 29 Vdd (+5V)
15 RxCLK+ 30 Vdd (+5V)
** LVDS Option : H (3.3V) or NC NS
L (GND)
** Rotate Option : H (3.3V)
L (GND)
JEIDA
U/D, R/L rotate
Normal
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 8/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
LVDS Option = L (GND)
Previous Cycle Current Cycle Next Cycle
Clock
www.panelook.com
RIN0+
RIN0-
RIN1+
RIN1-
RIN2+
RIN2-
RIN3+
RIN3-
LVDS Option = H (3.3V)
Previous Cycle Current Cycle Next Cycle
Clock
RIN0+
RIN0-
R2R7 G2G2R2R3 R4R5R6 R3
G3B2 B3B3G3G4 G5G6G6 G4
B4NA DEDEB4B5 B6B7NA B5
R0B1 NANAR0R1 G0G1B0 R1
R0R5 G0G0R0R1 R2R3R4 R1
RIN1+
RIN1-
RIN2+
RIN2-
RIN3+
RIN3-
G1B0 B1B1G1G2 G3G4G5 G2
B2NA DEDEB2B3 B4B5NA B4
R6B7 NANAR6R7 G6G7B6 R7
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 9/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
BACKLIGHT CONNECTOR PIN CONFIGURATION -
www.panelook.com
Item Symb.
Input Voltage --- 21.6 24.0 26.4 VDC
Input Current
Input Power
Inrush Current, 0.3ms
Output Frequency VDDB=24V 63.0 66.0 69.0 KHz
On/Off Control Voltage VDCVBLON
On/Off Control Current VDDB=24V -1.0 --- 1.5 mADC
Dimming Control Voltage I_VPWM
Dimming Control Current I_DIM MIN VDDB=24V --- --- 1.5 mADC
External PWM Control Voltage E_PWM VDC
External PWM Control Current --- --- --- 1.5 mADC
External PWM Duty Ratio --- 50 --- 100 %
External PWM Frequency --- 150 --- 300 Hz
Electrical specification
VDDB
IDDB
PDDB
IRUSH
FBL
OFF VDDB=24V -0.3 --- 0.8
IBLO N
MAX VDDB=24V --- 0 ---
MIN VDDB=24V --- 5.0 ---
MAX --- 3.0 --- 5.0
MIN --- -0.3 --- 0.8
E_IPWM
E_DPWM
E_FPWM
VDDB=24V
Dimming MAX
VDDB=24V
Dimming MAX
VDDB=24V
Dimming MAX
ON VDDB=24V 3.0 --- 5.0
Min Typ Max
Spec
4.3 4.8 5.3 ADC
--- 115 132 W
--- --- 6.0 ADC
Ta=255, Turn on for 45minutes
Input specification
CN1: JST JST PHR-14
UnitCondition
VDC
No Function Description
1 VDDB (Main Power) DC input 24.0 VDC
2 VDDB (Main Power) DC input 24.0 VDC
3 VDDB (Main Power) DC input 24.0 VDC
4 VDDB (Main Power) DC input 24.0 VDC
5 VDDB (Main Power) DC input 24.0 VDC
6 GND Ground
7 GND Ground
8 GND Ground
9 GND Ground
10 GND Ground
11 VDIM (LCD Bright) Brightness control signal input (0~3.3V)
(GND : Maximum brightness)
12 BLON (Enable voltage) TTL, H : ON, L : Off
13 E_PWM External PWM input for dimming control
14 GND Ground
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 10/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
y
3-3 Signal Timing Specifications
This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications for it’s proper operation.
* Timing Table
DE only Mode
Vertical Frequency Range A
Signal Item Symbol Min Type Max Unit
Period Tv 789 806 822 Th
Vertical
Section
Horizontal
Section
Clock
Vertical
Frequency
Horizntal
Frequency
Active
Blanking Tblk (v) 21 38 54 Th
Period Th 1414 1560 1722 Tclk
Active
Blanking Tblk (h) 48 194 356 Tclk
Frequenc
Frequency
Frequency Freq 47.32 49.32 KHz
www.panelook.com
Tdisp
(v) Th
Tdisp
(h) Tclk
1/Tclk 65 76 88 MHz
Freq 58
768
1366
60 62 Hz
Vertical Frequency Range B
Signal Item Symbol Min Type Max Unit
Period Tv 789 806 822 Th
Tdisp
Vertical
Section
Horizontal
Section
Clock
Vertical
Frequency
Horizntal
Frequency
Active
Blanking Tblk (v) 21 38 54 Th
Period Th 1414 1560 1722 Tclk
Active
Blanking Tblk (h) 48 194 356 Tclk
Frequency 1/Tclk 54 63 74 MHz
Frequency Freq
Frequency Freq 39.45 41.10 KHz
(v) Th
Tdisp
(h) Tclk
48
1.) Display position is specific by the rise of DE signal only.
Horizontal display position is specified by the falling edge of 1
768
1366
50 52 Hz
st
DCLK right after the rise of
ENAB, is displayed on the left edge of the screen.
Vertical display position is specified by the rise of DE after a “Lo w” level period equivalent
to eight times of horizontal period. The 1
st
data corresponding to one horizontal line after the
rise the of ENAB is displayed at the top line of screen.
3.) If a period of DEB “High” is less than 1366 DCLK or less than 768 lines, the rest of the
screen displays black.
4.) The display position does not fit to the screen if a period of DE “High” and the effective
data period do not synchronize with each other.
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 11/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3-4 Signal Timing Waveforms
RGB Dat a
Pixel
136 6
InvalidData
www.panelook.com
DE
CLK
Tcl k
RGB
Data
Line
768
InvalidData Invalid Data
DE
1
2
3
4
5
6
1366
Invalid Data
1
2
Line
Pi xel
Pix el
Pixel
Pix el
Pixel
Pi xel
Pi xel
Pix el
Pixel
Tdis p(h)
Th
1
Line
2
Line
3
Line
4
Line
768
Th
Tv
Tdisp(v)
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 12/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3-5 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the
color; the higher the binary input, the brighter the color. The table below provides a reference for color versus
data input.
Color
MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
www.panelook.com
COLOR DATA REFERENCE
Input Color Data
RED
MSB LSB
GREEN
BLUE
MSB LSB
Basic
Color
RED
GREEN
BLUE
Black 0 0 0 0 0 0 0 0 0000000000000000
Red(255) 111111110000000000000000
Green(255) 0 0 0 0 0 0 0 0 1111111100000000
Blue(255) 000000000000000011111111
Cyan 000000001111111111111111
Magenta 111111110000000011111111
Yellow 1 1 1 1 1 1 1 1 1111111100000000
White 1 1 1 1 1 1 1 1 1111111111111111
RED(000) 0 0 0 0 0 0 0 0 0000000000000000
RED(001) 0 0 0 0 0 0 0 1 0000000000000000
----
RED(254) 1 1 1 1 1 1 1 0 0000000000000000
RED(255) 1 1 1 1 1 1 1 1 0000000000000000
GREEN(000)000000000000000000000000
GREEN(001)000000000000000100000000
----
GREEN(254)000000001111111000000000
GREEN(255)000000001111111100000000
BLUE(000) 000000000000000000000000
BLUE(001) 000000000000000000000001
-------
BLUE(254) 000000000000000011111110
BLUE(255) 000000000000000011111111
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 13/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3-6 Power Sequence
www.panelook.com
Power Supply For LCD
V
dd
(+5V) & VDDB
Interface Signal
Power For LAMP
(BLON)
t1 470 - 1000 us
t2 50 - 100 ms
t3 800 - - ms
t4 200 - - ms
t5 50 - - ms
t6 0.47 - 30 ms
t7 1 - - s
90%
10%
GND
t1 t2
GND
10% 10%
Valid Data
t3 t4
ValuesParameter
Min. Typ. Max.
90%
10% 10%
t5 t6 t7
Units
(1) Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD
operation or the LCD turns off before the back-light turns off, the display may momentarily become
abnormal screen.
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 14/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle ofandequal to 0.
Fig.1 1 presents additional information concerning the measurement equipment and method.
www.panelook.com
Parameter
Symbol
Values
Units Notes
Min. Typ. Max.
Contrast Ratio CR 650 800 1
Surface Luminance, white LWH 350 380
Luminance Variation
Rise Time Tr
Time
Decay Time Tr
WHITE
9 p 1.40 3
R
D
12 35 msResponse
12 35 ms
cd/
Gray to Gray
Color Coordinates
RED R
R
GREEN G
G
BLUE B
B
WHITE W
W
X
Y
X
Y
X
Y
X
Y
Typ.-0.03
0.640
0.330
0.270
0.600
Typ.+0.03
0.150
0.060
0.280
0.290
Viewing Angle
x axis, right(=0)
x axis, left(=180)
y axis, up(=90)
y axis, down (=0)
r
l
u
d
85 Degree 5
85
85
85
2
4
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 15/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Note:
1. Contrast Ratio (CR) is defined mathematically as:
www.panelook.com
Contrast Ratio=
Surface Luminance of
Surface Luminance of
L
on1
L
off1
2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all
pixels displaying white. From more information see FIG 2. When VDDB = 24V, IDDB = 5A. L
WH
=Lon1
Where Lon1 is the luminance with all pixels displaying white at center 1 location.
3. The variation in surface luminance, WHITE is defined (center of Screen) as:
WHITE(9P)
= Maximum(L
on1
, L
on2
,…,L
)/ Minimum(L
on9
on1
, L
on2
,…L
on9
)
4. Response time is the time required for the display to transfer between any two gray level(Average) For
additional information see FIG3.
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface.
For more information see FIG4.
FIG. 2 Luminance
V
H/2
H/6
1
7
23
V/2V/6
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 16/25
No Reproduction and Redistribution Allowed
H
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
FIG.3 Response Time
The response time is defined as the following figure and shall be measured by switching the input signal for
“black” and “white”.
www.panelook.com
100%
90%
L0,15,L31,.L255
Luminance
10%
0%
Tr
FIG.4 Viewing angle
D
L0,15,L31,.L255
Tr
R
L0,15,L31,
.L255
Time
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 17/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T315XW01 V2. In addition the figures in
the next page are detailed mechanical drawing of the LCD.
Outline Dimension
Weight 6000g Typ.
www.panelook.com
Horizontal 760.0mm
Vertical 450.0mm
Depth 47mm
Horizontal 703.6mmBezel Opening
Vertical 398.3mm
Horizontal 697.68mmActive Display Area
Vertical 392.26mm
Surface Treatment AG, 3H
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 18/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Front View
www.panelook.com
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 19/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Rear View
www.panelook.com
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 20/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
6. Reliability
Environment test condition
No Test Item Condition
1 High temperature storage test
2 Low temperature storage test
3 High temperature operation test
4 Low temperature operation test
5 Vibration test
(non-operating)
6 Shock test
(non-operating)
7 Vibration test
(with carton)
8 Drop test
(with carton)
9 Altitude
Storage/shipment
www.panelook.com
Ta=60 240h
Ta=-20 240h
Ta=50 80%RH 240h
Ta=0 240h
Wave form: random
Vibration level : 1.0G RMS
Bandwidth : 10-500Hz
Duration: X, Y, Z 20min
One time each direction
Shock level: 50G
Waveform: half since wave, 11ms
Direction: X, Y, Z
One time each direction
Random
Vibration:10~200Hz,1.5G,30minutes
in each X,Y,Z direction
Height: 53.3cm
1 corner, 3 edges, 6 surfaces
(ASTMD4169-I)
50,000 feet (12Kpa)
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 21/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
7. International Standard
7-1. Safety
(1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995
Standard for Safety of Information Technology Equipment Including electrical Business Equipment.
(2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association,
Standard for Safety of Information Technology Equipment Including Electrical Business Equipment.
(3) EN60950 : 1992+A2: 1993+A2: 1993+C3: 1995+A4: 1997+A11: 1997
IEC 950: 1991+A1: 1992+A2: 1993+C3: 1995+A4:1996
European Committee for Electrotechnical Standardization (CENELEC)
EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical
Business Equipment.
www.panelook.com
7-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 22/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
8. Packing
Label : 83mm * 23mm
Carton Label : 80mm * 40mm
www.panelook.com
AU Optronics
MODEL NO: T315XW01 VX
PART NO: 9731T01.XXX
CUSTOMER NO:
CARTON NO:
Made in Taiwan
*PM100-01A1600001*
QTY: 3
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 23/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Carton :
3pcs Modules
www.panelook.com
947(L)mm * 290(W)mm * 595(H)mm
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 24/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1 MOUNTING PRECAUTIONS
(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not
applied to module. And the case on which a module is mounted should have sufficient strength so
that external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the
polarizer. Transparent protective plate should have sufficient strength in order to the resist external
force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the
former generates corrosive gas of attacking the polarizer at high temperature and the latter
causes circuit break by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than
HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch
the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the
polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft
materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for
cleaning the adhesives used to attach front/ rear polarizers. Do not use acetone, toluene and
alcohol because they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer
causes deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
www.panelook.com
9-2 OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
V=200mV(Over and under shoot voltage)
(2) Response time depends on the temperature. (In lower temperature, it becomes longer..)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower
temperature, response time (required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference
shall be done by system manufacturers. Grounding and shielding methods may be important to
minimize the interface.
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 25/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
9-3 ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE
Strong light exposure causes degradation of polarizer and color filter.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5 and 35 at normal humidity.
www.panelook.com
(2) The polarizer surface should not come in contact with any other object. It is recommended that they be
stored in the container in which they were shipped.
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM
(1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled
off, static electricity is generated between the film and polarizer. This should be peeled off slowly and
carefully by people who are electrically grounded and with well ion-blown equipment or in such a
condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of flue still on the Bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is recognized, please
wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.
©Copyright AU Optronics, Inc.
January, 2003 All Rights Reserved. T315XW01 V8 - Specs. Ver 1.0 26/25
No Reproduction and Redistribution Allowed
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...