Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
(V ) Preliminary Specifications
( ) Final Specifications
Module
Model Name
Customer Date
15 Inch Color TFT-LCD
G150XG02 V1
Approved by Date
Checked &
Approved by
Note: This Specification is subject to change
without notice.
Debbie Chiu
Prepared by
2009/11/17
Hsiao Chun Lin 2009/11/17
General Display Business Division /
AU Optronics corporation
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
Contents
1. Operating Precautions..................................................................................... 4
2. General Description ......................................................................................... 5
2.1 Display Characteristics ...................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
3. Functional Block Diagram ............................................................................... 9
4. Absolute Maximum Ratings........................................................................... 10
4.1 Absolute Ratings of TFT LCD Module.............................................................................. 10
4.2 Absolute Ratings of Environment..................................................................................... 10
5. Electrical Characteristics............................................................................... 11
5.1 TFT LCD Module ............................................................................................................. 11
5.2 Backlight Unit................................................................................................................... 13
6. Signal Characteristic...................................................................................... 15
6.1 Pixel Format Image..........................................................................................................15
6.2 Scanning Direction........................................................................................................... 15
6.3 Signal Description ............................................................................................................ 16
6.4 The Input Data Format..................................................................................................... 17
6.5 Interface Timing ............................................................................................................... 18
6.6 Power ON/OFF Sequence ............................................................................................... 19
7. Connector & Pin Assignment ........................................................................ 20
7.1 TFT LCD Module: LVDS Connector................................................................................. 20
7.2 Backlight Unit: Lamp Connector ......................................................................................22
7.3 Lamp Connector Pin Assignment..................................................................................... 22
8. Reliability Test Criteria................................................................................... 23
9. Mechanical Characteristics ........................................................................... 24
9.1 LCM Front View and Rear View....................................................................................... 24
9.2 LCM Outline Dimension (Front View)............................................................................... 25
9.3 LCM Outline Dimension (Rear View) ............................................................................... 26
10. Label and Packaging.................................................................................... 27
10.1 Shipping Label (on the rear side of TFT-LCD display) ................................................... 27
10.2 Carton Package .............................................................................................................27
11 Safety.............................................................................................................. 28
11.1 Sharp Edge Requirements............................................................................................. 28
11.2 Materials......................................................................................................................... 28
11.3 Capacitors ...................................................................................................................... 28
11.4 National Test Lab Requirement...................................................................................... 28
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
Record of Revision
Version and Date Page Old description New Description
0.0 2009/6/15 All First Edition
0.1 2009/10/30 13
CCFL operation range Max.=6.5
CCFL operation range Max.=7.0
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
1. Operating Precautions
1) Since front polarizer is easily damaged, please be cautious and not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open nor modify the module assembly.
8) Do not press the reflector sheet at the back of the module to any direction.
9) In case if a module has to be put back into the packing container slot after it was taken
out from the container, do not press the center of the CCFL Reflector edge. Instead,
press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be
damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module.
The LCD module should be supplied by power complied with requirements of Limited
Power Source (IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CFL in it is supplied by Limited Current
Circuit (IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
15) Severe temperature condition may result in different luminance, response time and
lamp ignition voltage.
16) Continuous operating TFT-LCD display under low temperature environment may
accelerate lamp exhaustion and reduce luminance dramatically.
17) The data on this specification sheet is applicable when LCD module is placed in
landscape position.
18) Continuous displaying fixed pattern may induce image sticking. It’s recommended to
use screen saver or shuffle content periodically if fixed pattern is displayed on the
screen.
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
2. General Description
G150XG02 V1 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD display,
a driver circuit, and a backlight system. The screen format is intended to support XGA
(1024(H) x 768(V)) screen and 16.2M (RGB 8-bits) or 262k colors (RGB 6-bits). All input
signals are LVDS interface compatible. Inverter card of backlight is not included. All the
design rules of this module can correspond to PSWG standard.
G150XG02 V1 is designed for industrial display applications.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25
Items Unit Specifications
Screen Diagonal [inch] 15
Active Area [mm] 304.128(H) x 228.096(V)
к
condition:
Pixels H x V 1024x3(RGB) x 768
Pixel Pitch [mm] 0.297 x 0.297
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN, Normally White
Nominal Input Voltage VDD [Volt] 3.3 typ.
Typical Power Consumption [Watt] 21W ( VDD line + CCFL line, exclude inverter)
Weight [Grams] 1350g (typ.)
Physical Size [mm] 326.5(H)x 253.5(V) x 14.4(D) (typ.)
Electrical Interface 1 channel LVDS
Surface Treatment Anti-glare, Hardness 3H
Support Color 16.2M / 262K colors
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance RoHS Compliance
o
C]
[
o
C]
[
-30 to +85
-30 to +85
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
White Luminance [cd/m2]
Uniformity
Contrast Ratio
Cross talk %
Response Time
Viewing Angle
Color / Chromaticity
Coordinates
(CIE 1931)
Color Gamut %
[msec] Rising
[msec] Falling
[msec] Raising + Falling
[degree]
[degree]
[degree]
[degree]
IRCFL= 6.5mA
(center point)
įWHITE ,5 Points
400 700 - 4
- 1.2 1.5 5
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
470 550 - 1
1.2 - 1, 2, 3
-
- 2.3
- 8
60
60
55
50
T
yp.
-0.03
65 -
5.7
70
70
65
60
0.64
0.34
0.30
0.6
0.15
0.1
0.31
0.32
-
-
-
-
T
yp.
+0.03
G150XG02 V1
6
7
Note 1: Measurement method
Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent)
Aperture 1 with 50cm viewing distance
Test Point Center
Environment < 1 lux
ш
LCD Module
SR_3 or
equivalent
Measuring distance
Module Driving Equipment
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6/28
www.panelook.com
Global LCD Panel Exchange Center
g
www.panelook.com
G150XG02 V1
Note 2: Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all
pixels displaying white. More information see below chart. When I=6.5mA, L=550nits(Typ.) L=Lon1,
Where Lon1 is the luminance with all pixels displaying white at center 1 location.
Note 3: The variation in surface luminance, įWHITE is defined (center of Screen) as:
įWHITE(5P)=Maximum(Lon1, Lon2,…,Lon5)/ Minimum(Lon1, Lon2,…,Lon5)
Κ
Note 4
Note 5
Definition of contrast ratio (CR):
Κ
Definition of cross talk (CT)
Contrast ratio (CR)=
Brightness on the “White” state
Bri
htness on the “Black” state
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
1/2
A
184 gray level
B
1/6
1/6
1/2
1/2
2/3 1/3
A’
1/6
B’
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1/6
1/3
1/2
2/3
7/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
Note 6: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “White” to “Black”
(falling time) and from “Black” to “White” (rising time), respectively. The response time interval is between 10% and
90% of amplitudes. Please refer to the figure as below.
Optical
Optical
response
response
%
100
90
90
10
10
0
0
Tf
White Black White
White Black White
Tr
Tr
Note 7: Definition of viewing angle
Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as below: 90° (ș)
horizontal left and right, and 90° (ĭ) vertical high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated to its center to develop the desired
viewing angle.
Њ
measurement
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
8/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
3. Functional Block Diagram
The following diagram shows the functional block of the 15 inch color TFT/LCD module:
LVDS
+ 3.3V
Connector
DC/DC
Converter
LVDS
Correction
AU ASIC
Gamma
Timing
Controller
RSDS
DC POWER
G1
Inverter
Source Driver IC
Gate Driver IC
1024(3)*768
G150XG02 V1
CCFL
D3072
TFT-LCD
Pixels
3804-F20N-06R / MSB240420E JST-BHR-03VS-1
Mating Type: HRS DF14-20S-1.25C SBH-001T-P0.5
G768
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
9/28
www.panelook.com
Global LCD Panel Exchange Center
[
www.panelook.com
4. Absolute Maximum Ratings
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit
Logic/LCD Drive Voltage Vin -0.3 +3.6
4.2 Absolute Ratings of Environment
Item Symbol Min Max Unit
Operating Temperature TOP -30 +85 [oC]
Operation Humidity HOP 8 90 [%RH]
Storage Temperature TST -30 +85 [oC]
Storage Humidity HST
Note: Maximum Wet-Bulb should be 39 and no condensation. к
8 90
[%RH]
G150XG02 V1
Volt]
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
G150XG02 V1 rev. 0.1
10/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Symbol Parameter Min Typ Max Units Remark
ᇹ
VDD
IDD
I
rush
PDD
Logic/LCD Drive
Voltage
VDD Current
LCD Inrush Current
VDD Power
Note 1: Measurement condition:
(High to Low)
Control
Signal
+3.3V
3.0 3.3 3.6 [Volt]
-
- -
-
R1
47K
R2
550 660 [mA]
3 [A]
1.9 2.2 [Watt]
Q3
AO6402
D6
D5
D2 S
D1
G
D2SD1D5
D6
Q3
G
AO6402
F1
10%
64 Gray Bar Pattern
(VDD=3.3V, at 60Hz)
Note 1
64 Gray Bar Pattern
(VDD=3.3V, at 60Hz)
(LCD Module Input)
C1
1uF/16V
VDD
VCC
1K
C3
0.01uF/25V
SW1
SW MAG-SPST
1 2
+12.0V
C2
1uF/25V
R2
1K
VR1
47K
90%
3.3V
10%
0V
470 us
VDD rising time
64 Gray pattern
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
11/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD is off.
Symbol Item Min. Typ. Max. Unit Remark
VTH
VTL
Ψ
VIDΨ Input Differential Voltage
VICM
Note: LVDS Signal Waveform.
Differential Input High Threshold - - 100
Differential Input Low Threshold -100 - -
Differential Input Common Mode
Voltage
100 400 600
1.1 1.45
[mV] VCM=1.2V
[mV] VCM=1.2V
[V]
VTH/VTL=
[mV]
100mV
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
12/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
5.2 Backlight Unit
5.2.1 Parameter guideline for CCFL
Following characteristics are measured under a stable condition using an inverter at 25 (Room Temperature):к
Symbol Parameter Min. Typ. Max. Unit Remark
IRCFL CCFL operation range
FCFL CCFL Frequency
ViCFL
o
C)
(0
CCFL Ignition Voltage - 1180 1480
3.0 6.5 7.0
40 46 65 [KHz] (Ta=25
(reference)
ViCFL
o
C)
(25
CCFL Ignition Voltage - 910 1140
(reference)
VCFL CCFL Discharge Voltage 567 630 693
CCFL Power consumption
PCFL
14.8 16.4 18
(inverter excluded)
Lamp Life
50,000 - Hrs
[mA]
rms
[Volt]
rms
[Volt]
rms
[Volt]
rms
[Watt]
(Ta=25
(Ta= 0
I = 6.5 mA
(Ta=25
I = 6.5 mA
(Ta=25
IRCFL=6.5mA
VCFL = Typ±10%
(Ta=25
IRCFL=6.5mA
(Ta=25
IRCFL = 6.5mA
o
C) Note 1
o
C) Note 2
o
C)
o
C)
o
C) Note 3
o
C) Note 3
o
C) Note 4
Note 1: IRCFL is defined as the return current of an inverter. (In Figure. 1)
Inverter
+
-
mA
Hi
Lamp
Lo
(Figure. 1: Measurement of return current)
A stable IRCFL is a current without flicker or biasing waveform provided by inverter that ensures the
backlight perform to its specification. The ideal sine waveform should be symmetric in positive and
negative polarities and the asymmetry rate of the inverter waveform should be below 10%.
Ip
Reference
I-p
(Note) Ip: Positive peak value
I-p: Negative peak value
Irms: Effective value
DC Bias = (| Ip – I-p| / Irms ) x 100 % <10%
Crest Factor = Ip or (I-p) / Irms should have the range within 1.414 +
10%
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
13/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
It is recommended to use the inverter with detection circuit ( ie: balance and protection circuit) to avoid
overvoltage, overcurrent, or mismatching waveform.
Note 2: CCFL frequency should be carefully determined to avoid interference between inverter and TFT LCD.
Higher frequency will induce higher leakage current and further impact lamp life.
Note 3: Calculator value for reference (IRCFLxVCFLx4=PCFL).
Note 4: The definition of lamp life means when any of following conditions happen:
a) Luminance falls to 50% or less of the initial value.
b) Normal lighting is no more available (flickering, pink lighting, no lighting, etc.)
c) Lamp voltage or lighting start voltage exceeds the specified value.
Lamp life time shortens according to
a) Placing methodology: mercury is unevenly distributed in portrait mounting
b) Environmental condition: low temperature reduces the presence of mercury vapor, which results in
approximately lamp life of 1,000 hours
c) CCFL surface temperature: Presence of gradient in lamp surface temperature causes uneven mercury
migration
d) Inverter design: its resonance capacitor should be fine-tuned according to the impedance of CCFL
e) Over driving current ( > 6.5 mA) shortens lamp life time dramatically.
Note 5: The display is with dual lamp design, and the CCFL current in above table refers to each lamp
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
14/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel format.
G150XG02 V1
6.2 Scanning Direction
The following figures show the image seen from the front view. The arrow indicates the direction of scan.
Fig. 1 Normal scan (Pin4, REV = Low or NC) Fig. 2 Reverse scan (Pin4, REV = High)
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
15/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential
signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the
second LVDS port(RxExxx) transmits even pixels.
3804-F20N-06R (E&T) / MSB240420E(STM)
Pin No. Symbol Description
1 VDD
2 VDD
3 VSS
4 REV
5 Rin0-
6 Rin0+
7 VSS
Power Supply, 3.3V (typical)
Power Supply, 3.3V (typical)
Ground
Reverse Scan selection *.Note1
- LVDS differential data input (R0-R5, G0)
+ LVDS differential data input (R0-R5, G0)
Ground
8 Rin1-
9 Rin1+
10 VSS
11 Rin2-
12 Rin2+
13 VSS
14 ClkIN-
15 ClkIN+
16 GND
17 Rin3-
18 Rin3+
19 VSS
20 SEL68
Note 1: Input signals shall be in low status when VDD is off.
- LVDS differential data input (G1-G5, B0-B1)
+ LVDS differential data input (G1-G5, B0-B1)
Ground
- LVDS differential data input (B2-B5, HS, VS, DE)
+ LVDS differential data input (B2-B5, HS, VS, DE)
Ground
- LVDS differential clock input
+ LVDS differential clock input
Ground
- LVDS differential data input (R6-R7, G6-G7,B6-B7)
- LVDS differential data input (R6-R7, G6-G7,B6-B7)
Ground
Selection for 6 bits/8bits LVDS data input *Note1
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
16/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6.4 The Input Data Format
6.4.1 SEL68
SEL68 = ”High” or “NC” for 6 bits LVDS Input
RxCLKIN
RxIN1
RxIN2
RxIN3
SEL68 = “Low” for 8 bits LVDS Input
RxCLKIN
RxIN1
RxIN2
G0 R5 R4 R3 R2 R1 R0
B1 B0 G5 G4 G3 G2 G1
DE VS HS B5 B4 B3 B2
G0 R5 R4 R3 R2 R1 R0
B1 B0 G5 G4 G3 G2 G1
G150XG02 V1
RxIN3
RxIN4
DE VS HS B5 B4 B3 B2
RSV
B7 B6 G7 G6 R7 R6
Note1: Please follow PSWG.
Note2: R/G/B data 7:MSB, R/G/B data 0:LSB
Signal Name Description Remark
R7
R6
R5
R4
R3
R2
R1
R0
G7
G6
G5
G4
G3
G2
G1
G0
B7
B6
B5
B4
B3
B2
B1
B0
Red Data 7
Red Data 6
Red Data 5
Red Data 4
Red Data 3
Red Data 2
Red Data 1
Red Data 0
Green Data 7
Green Data 6
Green Data 5
Green Data 4
Green Data 3
Green Data 2
Green Data 1
Green Data 0
Blue Data 7
Blue Data 6
Blue Data 5
Blue Data 4
Blue Data 3
Blue Data 2
Blue Data 1
Blue Data 0
Red-pixel Data
For 8Bits LVDS input
MSB: R7 ; LSB: R0
For 6Bits LVDS input
MSB: R5 ; LSB: R0
Green-pixel Data
For 8Bits LVDS input
MSB: G7 ; LSB: G0
For 6Bits LVDS input
MSB: G5 ; LSB: G0
Blue-pixel Data
For 8Bits LVDS input
MSB: B7 ; LSB: B0
For 6Bits LVDS input
MSB: B5 ; LSB: B0
RxCLKIN LVDS Data Clock
DE Data Enable Signal When the signal is high, the pixel data
shall be valid to be displayed.
VS Vertical Synchronous Signal
HS Horizontal Synchronous Signal
Note: Output signals from any system shall be low or Hi-Z state when VDD is off.
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
17/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
G150XG02 V1
6.5 Interface Timing
6.5.1 Timing Characteristics
Signal Parameter Symbol Min. Typ. Max. Unit
Clock Timing Clock frequency 1/ T
Vsync Timing Vertical
Section
Period T
Active T
Blanking T
Hsync Timing Horizontal
Section
Period T
Active T
Blanking T
Note: Frame rate is 60 Hz.
Note: DE mode.
Note : Typical value refer to VESA STANDARD
Clock
V
VD
VB
H
HD
HB
50 65 81
776 806 1024
768 768 768
8 38 256
1054 1344 2048
1024 1024 1024
30 320 1024
MHz
T
Line
T
Clock
6.5.2 Input Timing Diagram
DOTCLK
Input
Data
DE
DE
T
CLOCK
Invaild
Data
T
HB
Input Timing Definition ( DE Mode)
Pixel1Pixel2Pixel3Pixel
T
HD
T
H
T
VB
T
V
N-1
T
VD
Pixel
N
Invaild
Data
Pixel
1
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
18/28
www.panelook.com
Global LCD Panel Exchange Center
g
www.panelook.com
G150XG02 V1
6.6 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as below. Interface signals are also shown in the chart. Signals from any
system shall be Hi-Z state or low level when VDD is off.
Power Supply VDD
10%
LVDS Signal
Backli
ht On
T1
90%
T2
VALID
DATA
T3
90%
T5
T4
Power ON/OFF sequence timing
T6
10%
T7
Parameter
Min. Typ. Max.
T1
T2
T3
T4
T5
T6
T7
The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn
off the power when you plug the cable into the input connector or pull the cable out of the connector.
0.5 - 10 ms
0 40 50 ms
200 - - ms
200 - - ms
0 16 50 ms
0 - 10 ms
1000 - - ms
Value
Units
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
19/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
7. Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module: LVDS Connector
Connector Name / Designation Signal Connector
Manufacturer E&T or compatible
Connector Model Number 3804-F20N-06R / MSB240420E
Adaptable Plug HRS DF14-20S-1.25C
Pin# Signal Name Pin# Signal Name
1
3
5
7
9
11
13
15
17
19
VDD
VSS
Rin0-
VSS
Rin1+
Rin2-
VSS
ClkIN+
Rin3-
VSS
2 VDD
4 REV
6
8 Rin1-
10 VSS
12 Rin2+
14
16 GND
18 Rin3+
20 SEL68
Rin0+
ClkIN-
G150XG02 V1
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
20/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
7.1.1 Connector Illustration
G150XG02 V1
SEL68
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
21/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
7.2 Backlight Unit: Lamp Connector
Connector Name / Designation Lamp Connector
Manufacturer JST or compatible
Connector Model Number JST BHR-03VS-1 or compatible
Mating Model Number SBH-001T-P0.5 or compatible
7.3 Lamp Connector Pin Assignment
Pin# Symbol Cable color Signal Name
1 HV Red/Black Lamp High Voltage
2 NC NC No Connection
3 LV Blue/White Ground
Cable length: 140 s10 mm
G150XG02 V1
Connector-output position: right side (front view)
Lamp assembly design shall be easy for replacement and repair
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
22/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
8. Reliability Test Criteria
Items
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
Hot Storage
Cold Storage
Thermal Shock
Test
Shock Test
(Non-Operating)
Vibration Test
(Non-Operating)
Required Condition Note
к
80%,300 hours
50 /
к
,300 hours
85
к
,300 hours
-30
к
85 ,300 hours
к
-30 ,300 hours
кк
-20 /30 min ,60 /30 min ,100cycles
50G,20ms,Half-sine wave,( ±X, ±Y, ±Z)
1.5G, (10~200Hz, P-P)
30 mins/axis (X, Y, Z)
G150XG02 V1
On/off test
ESD
Note1: According to EN61000-4-2, ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
On/10 sec, Off/10 sec, 30,000 cycles
Contact Discharge: ± 8KV, 150pF(330ȍ ) 1sec, 8 points, 25 times/ point
Air Discharge: ± 15KV, 150pF(330ȍ ) 1sec, 8 points, 25 times/ point
Note 1
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
23/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
24/28
G150XG02 V1 rev. 0.1
G150XG02 V1
9. Mechanical Characteristics
9.1 LCM Module
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
25/28
G150XG02 V1 rev. 0.1
G150XG02 V1
9.2 LCM Outline Dimension (Front View)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
26/28
G150XG02 V1 rev. 0.1
G150XG02 V1
9.3 LCM Outline Dimension (Rear View)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
10. Label and Packaging
10.1 Shipping Label
10.2 Carton Package
Max capacity: 10 TFT-LCD module per carton (10pcs * 1 layers)
Max weight: 14 kg per carton
Outside dimension of carton: 490(L)mm* 390(W )mm* 360(H)mm
(on the rear side of TFT-LCD display)
G150XG02 V1
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
27/28
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
11 Safety
11.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
11.2 Materials
11.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are
used, they will be reviewed and approved by the responsible AUO toxicologist.
11.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the
module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability
rating will be printed on the printed circuit board.
G150XG02 V1
11.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from
being inserted backwards.
11.4 National Test Lab Requirement
The display module will satisfy all requirements for compliance to:
UL 1950, First Edition U.S.A. Information Technology Equipment
G150XG02 V1 rev. 0.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
28/28
www.panelook.com
Loading...