Aukey SK-M52 User Manual
User Manual
Soundbar
Contents
English
Deutsch
Français
Español
Italiano
01~09
10~18
19~27
28~36
37~45
Thank you for purchasing the AUKEY SK-M52 Soundbar. Please read this user manual carefully and keep it for future
FCC ID: 2AFHP-SK-M52
3.5mm In
Optical In
USB
Input: AC 100V - 240V
50Hz / 60Hz
reference. If you need any assistance, please contact our support team with your product model number and
Amazon order number.
Package Contents
Soundbar
Remote Control
Twin Speaker Stands
Toslink Optical Cable (1m / 3.28ft)
3.5mm Audio Cable (0.6m / 1.97ft)
3.5mm to RCA Audio Cable (1.15m / 3.77ft)
Wall Mounting Kit (Two Screws and Anchors)
Two Rubber Foot Pads
User Manual
Warranty Card
Product Diagram
Volume Up / Next Track
Multi-Function Button / LED Indicator
Volume Down / Previous Track
+
3.5mm Audio Input
Optical Input
USB Port
Specifications
Model
Technology
Drivers
Audio Output Power
Frequency Response
Signal-to-Noise Ratio
Impedance
Power Input
Bluetooth Operating Range
Dimensions
Weight
SK-M52
BT 4.2, A2DP, AVRCP, DSP
2 x 75mm / 2.95” speaker drivers
2 x 30W
80Hz – 20kHz
≥80dB
8 ohm
AC 110–240V 50/60Hz
Up to 10m / 33ft
L: 495 x 75 x 66mm / 19.48” x 2.95” x 2.59”
R: 475 x 75 x 66mm / 18.7” x 2.95” x 2.59”
Pedestal: 165 x 155mm / 6.5” x 6.09”
1.8kg / 3.96oz
- 01 -
Positioning the Soundbar
For the best sound experience, position the soundbar 3 to 8 meters from the listening area.
Soundbar
3-8 meters
The soundbar has a flexible, detachable design that allows three main setups. Lay flat on your tabletop, wall mount
above or below the TV, or use as twin tower speakers on the provided stands.
- 02 -
Place on a Flat Surface
A.
Attach the two included rubber foot pads to the bottom of the soundbar (only if using this setup) for stable use
1.
and soft surface contact without vibration. For best stability and support, use the position of the two keyhole
mounting slot brackets as a reference and place the pads slightly nearer the center of the soundbar
Keyhole Mounting Slot Bracket
Suggested Pad Position
Place the soundbar horizontally on a flat surface such as a TV unit or shelves and align it centrally with the TV
2.
screen. Allow some space between the speaker and the wall. Don’t place inside a cabinet or on a walled shelf.
Follow this guidance for best sound output and good airflow around the soundbar
√
×
Keyhole Mounting Slot Bracket
Suggested Pad Position
Mount on the WallB.
WARNING: If you don’t feel confident to correctly and securely wall-mount the soundbar, seek the assistance
of an experienced person or professional
Install the speaker on a vertical, flat, reinforced area of wall. For plaster walls, it is recommended to screw into
wall studs for greater security. For optimum performance, allow at least 25mm / 1” distance between the
soundbar and the TV.
25mm / 1”
25mm / 1”
- 03 -
Drill two holes in the wall. The holes should be:
1.
At least 54mm / 2
●
1
/8” below the TV or 37mm / 17/16” above the TV (for 25mm / 1” distance between the TV and
soundbar). Add to this for greater spacing if desired
37mm / 17⁄16”
54mm / 21⁄8”
5
727mm / 28
/8” apart (and level)●
727mm / 285/8”
2.
Insert the anchors (unless screwing into wall studs); then screw in the screws (included) until they protrude from
the wall by 5–6mm / about
7
/32” (including screw head)
5–6mm / about
7
/32”
Connect the included Toslink optical cable to the unit, and the 3.5mm cable too if you intend to use it. You can also
3.
connect a USB extension cable (not included) to conveniently connect external USB devices to the unit
Before hanging the soundbar on the wall, decide whether you need to route connected cables up or down.
4.
According to this, either loop them over the top of the soundbar or allow them to hang down from the back so
they are ready to connect directly once the soundbar is mounted
Align the keyhole mounting slot bracket holes on the rear of the unit with the screws. Hang the unit on the two
5.
screws by slightly tilting the unit, pushing it onto the screws, and then lowering to slot in. Support the unit until you
are sure it’s correctly and securely fitted
- 04 -
Use as Tower Speakers
C.
Place the included speaker stands to the left and right of your TV or PC. The stand with the black part on top
1.
goes on the left and the thicker stand on the right (as you face the screen)
2.
Separate the left and right speakers by twisting the two sides of the soundbar in opposite directions (rotate the
sections clockwise relative to the center)
3.
Place the speakers on the stands by matching the flat corners of the two shapes and twist 45 degrees
counter-clockwise so the speakers face directly forward. The soundbar section with the silver end and controls
goes on the left stand and the other section on the right stand
Connecting Your Device to the Soundbar
There are three connection ports to choose from.
A. Connect to Optical Input
B.Connect to Audio Input
Optical Output
Audio Output
Optical Input
Audio Input
- 05 -
Toslink Optical Cable
Toslink Optical Cable
3.5mm to RCA Cable
Audio Input
3.5mm Audio Cable
C. Connect to USB Port
USB Port
USB Flash Drive
(up to 32GB)
Using the Soundbar
Powering On / Off
Plug the soundbar into a wall outlet. It will automatically enter standby mode and the LED indicator will light
1.
solid red
Short-press the multi-function button to turn on the soundbar
2.
To turn off, press and hold the multi-function button for 2 seconds or unplug from wall outlet
3.
Playing Audio via Optical Input Connection
Remove the small protective rubber end caps from the connectors of the included Toslink optical cable.
1.
Connect the soundbar to your TV using this cable, fully inserting the connectors so they click in
Turn on the soundbar and then short-press the multi-function button to switch to optical input mode with
2.
the LED indicator lit up white
In TV sound settings, select the soundbar optical connection (‘Audio Out/Optical,’ ‘Audio System,’ or
3.
similar) as the speaker (output for audio) instead of the TV speakers
4.
Set your TV audio format to PCM (digital audio out / optical) instead of DTS or others
- 06 -
Notes
The required settings may be in an ‘Advanced’ or ‘Expert’ section of the sound settings
●
Refer to your TV’s user manual for further details about sound settings and connections
●
Playing Audio via BT Connection
Turn on soundbar and then short-press the multi-function button to switch to BT mode with the LED indicator
1.
flashing blue rapidly
Activate the pairing function on your phone or other compatible device and select ‘AUKEY SK-M52’
2.
If a code or PIN is required for pairing, enter ‘0000’
3.
When successfully paired, you will hear a tone and the LED indicator will stay on
4.
The remote control includes BT mode playback controls
5.
Notes
If your paired device is switched off or manually disconnected, the soundbar will automatically enter pairing
●
mode
If the connected device exceeds the operating range, the soundbar will disconnect. The connection to the last
●
successfully connected device will be re-established once you re-enter wireless range. To connect to other
devices, repeat the above pairing steps
There is no automatic shutdown in pairing mode. The soundbar will remain in pairing mode even if no device is
●
paired, so switch off if not in use
Playing Audio via 3.5mm Audio Input (Aux) Connection
Connect the soundbar to your PC, tablet, smartphone, TV, or other device using the included 3.5mm audio
1.
cable or 3.5mm to RCA audio cable
Short-press the multi-function button to switch to audio input mode with the LED indicator lit up green
2.
In this mode, playback can only be controlled on your connected device
3.
Note
For some computers, you may need to access the audio control panel to manually set the soundbar as the
●
default audio device
Playing Audio via USB Port
The soundbar automatically switches to USB input mode with the LED indicator lit up purple when a USB flash drive
is inserted (this mode isn’t selectable on the soundbar or remote control unless a USB flash drive is connected).
Ensure that your USB flash drive contains MP3 or WMA audio files (other file types not supported)
1.
Connect the USB flash drive to the USB port on the soundbar (or your own USB extension cable connected to the
2.
USB port); music will automatically play
The remote control includes USB input mode playback controls
3.
Notes
Maximum storage size supported for USB flash drive is 32GB
●
USB input mode won’t function if the USB flash drive has no MP3 or WMA audio files
●
When USB flash drive is removed, the soundbar will automatically enter audio input mode with the LED indicator
●
flashing green
The soundbar automatically plays compatible audio tracks continuously in a loop in USB input mode unless you
●
manage playback with USB input mode playback controls
- 07 -
Using the Remote Control
POWER
①
INPUT
②
RESET
③
BT CANCEL
④
⑤
⑥
⑦
BT/USBEQ
MUSIC
MOVIE
SPEECH
3D
TREBLE
BASS
VOL
⑧
⑨
Switch soundbar on or off (standby)
Toggle between different input modes (BT, Audio
Input, Optical). Your selected input mode is saved
for next time. USB input mode is only accessible
when a USB flash drive is inserted
Reset all soundbar volume levels and switch EQ
back to Music setting. Press and hold button for 2
seconds
Cancel BT connection. Press and hold button for 2
seconds to disconnect from the paired device.
Use the paired device to reconnect
Increase or decrease higher frequencies. Your
setting is saved for next time
Increase or decrease lower frequencies. Your setting
is saved for next time
Volume Control
Increase or decrease master volume
Mute or restore volume
EQ settings
MUSIC
Optimized for music
MOVIE
Optimized for movies
SPEECH
Optimized for voice clarity such as for news
broadcasts and TV shows
3D
Enhanced with surround sound effects for a
bigger movie experience
Controls on the Soundbar
Control
Adjust master volume
Skip to next / previous track (only in BT or USB input modes)
Switch input modes
- 08 -
Playback controls (for BT and USB input modes only)
Stop
Play / Pause
Next Track
Previous Track
Operation
Short-press volume up or volume down
Long-press volume up / volume down
Short-press multi-function button
LED Indicators
LED Indicator
Blue flashing rapidly
Blue on
White on
Purple on
Green on
Flashing steadily
Red on
Status
BT pairing mode
BT connected
Optical input mode
USB input mode
3.5mm audio input mode
Outputting sound (any mode)
Standby
Product Care & Use
AUKEY Direct isn’t responsible for damage or injury caused by incorrect installation or use
●
Keep away from liquids, extreme heat, and strong magnetic fields
●
Don’t use this soundbar at high volume for extended periods, as this may cause permanent hearing damage or loss
●
Unplug during thunderstorms or when not in use for extended periods of time
●
Warranty & Customer Support
For questions, support, or warranty claims, contact us at the address below that corresponds with your region.
Please include your Amazon order number and product model number.
Amazon US orders: support.us@aukey.com
Amazon EU orders: support.eu@aukey.com
Amazon CA orders: support.ca@aukey.com
Amazon JP orders: support.jp@aukey.com
*Please note, AUKEY can only provide after sales service for products purchased directly from AUKEY. If you have purchased from a different seller, please
contact them directly for service or warranty issues.
Notice for US
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation
FCC Rules
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna
● Increase the separation between the equipment and receiver
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
● Consult the dealer or an experienced radio/TV technician for help
Caution
Changes or modifications made to this device that are not expressly approved by AUKEY may void the user's authority
to operate this equipment.
- 09 -
Vielen Dank für Ihren Kauf von AUKEY SK-M52 Soundbar. Lesen Sie bitte diese Bedienungsanleitung sorgfältig
FCC ID: 2AFHP-SK-M52
3.5mm In
Optical In
USB
Input: AC 100V - 240V
50Hz / 60Hz
durch und bewahren für zukünftige Referenz auf. Sollten Sie jegliche Unterstützung brauchen, kontaktieren Sie
bitte unser Support-Team mit Ihrer Produktmodellnummer und Amazon-Bestellnummer.
Lieferumfang
Soundbar
Fernbedienung
Standfüße Doppellautsprecher
optisches Kabel TOSLINK (1 m)
3,5-mm-Audiokabel (0,6 m)
3,5-mm- zu RCA-Audiokabel (1,15 m)
Wandmontageset (2 Schrauben und Dübel)
2 Gummifuß-Pads
Bedienungsanleitung
Garantiekarte
Produktbild
Lautstärke +/Nächster Titel
Multifunktionstaste/LED-Anzeige
Lautstärke -/Vorheriger Titel
+
3,5-mm-Audioeingang
Optischer Eingang
USB-Anschluss
Technische Daten
Modell
Technologie
Treiber
Audioausgangsleistung
Frequenzbereich
Rauschabstand
Impedanz
Netzeingang
Bluetooth-Reichweite
Abmessungen
Gewicht
SK-M52
BT 4.2, A2DP, AVRCP, DSP
2 x 75 mm Lautsprechertreiber
2 x 30 W
80 Hz – 20 kHz
≥ 80 dB
8 Ohm
110 – 240 V, 50/60 Hz (Wechselstrom)
bis zu 10 m
L: 495 x 75 x 66 mm
R: 475 x 75 x 66 mm
Standfuß: 155 x 165 mm
1,8 kg
- 10 -
Positionierung der Soundbar
Für ein optimales Klangerlebnis sollten Sie die Soundbar in 3 bis 8 Metern Entfernung vom Zuhörerbereich
positionieren.
Soundbar
3-8 meters
Das Design der Soundbar ist flexibel und bietet drei Optionen: horizontal auf dem Sideboard/TV-Schrank/Fernsehtisch, an der Wand über bzw. unter dem Fernseher oder im Doppelpack als Säulenlautsprecher unter Verwendung
der mitgelieferten Standfüße.
- 11 -
Auf einer ebenen Unterlage
A.
Bringen Sie die zwei mitgelieferten Gummifuß-Pads an der Unterseite der Soundbar (nur bei diesem Aufbau) an,
1.
damit sie stabil steht und Schwingungen absorbiert bzw. gemindert werden. Tipp: Wir empfehlen die Anbringung von den beiden Schlüssellochbefestigungen aus gesehen etwas Richtung Mitte, um maximale Stabilität
zu gewährleisten
Schlüssellochbefestigung Schlüssellochbefestigung
Empfohlene Pad-Position Empfohlene Pad-Position
Positionieren Sie die Soundbar horizontal auf einer ebenen Oberfläche wie einem TV-Schrank oder Regal und
2.
richten Sie die Soundbar mittig zum Bildschirm aus. Die Soundbar sollte nicht direkt an die Wand angrenzen. Die
Soundbar sollte frei dastehen, d. h. nicht in Schubladen oder Ähnlichem positioniert werden. Bei Beachtung
dieser Anleitung versprechen wir ein optimales Klangerlebnis und gute Luftzirkulation um die Soundbar herum
√
×
WandmontageB.
WARNUNG: Wenn Sie Bedenken haben, ob Sie die Soundbar korrekt an der Wand montieren können, sollten
Sie ggf. einen Handwerker engagieren.
Montieren Sie die Soundbar an einem vertikalen, flachen und stabilen Wandbereich. Bei Gipswänden empfehlen wir die Verwendung von Wandstutzen, um die Stabilität zu erhöhen. Zum Zweck der optimalen Leistung
sollte der Abstand zwischen Soundbar und Fernseher mindestens 25 mm betragen.
25mm
- 12 -
25mm
Bohren Sie zwei Löcher in die Wand. Die Löcher sollten
1.
mindestens 54 mm unter dem Fernseher oder 37 mm über dem Fernseher (für einen Abstand von 25 mm
●
zwischen Fernseher und Soundbar) sein. Falls Sie einen größeren Abstand wünschen, bohren Sie die Löcher
entsprechend höher oder tiefer
37mm
54mm
Abstand: 727 mm (und waagerecht)●
727mm
Setzen Sie die Dübel ein (sofern Sie keine Wandstutzen verwenden); schrauben Sie nun die (mitgelieferten)
2.
Schrauben ein, bis sie 5 – 6 mm aus der Wand herausragen (einschließlich Schraubenkopf)
7
5–6mm / about
/32”
Schließen Sie das mitgelieferte optische Kabel (TOSLINK) an die Soundbar an und ebenso das 3,5-mm-Kabel, falls Sie
3.
es benötigen. Sie können zudem ein USB-Verlängerungskabel (nicht inbegriffen) anschließen, um externe
USB-Geräte bequem an die Soundbar anschließen zu können
Bevor Sie die Soundbar an die Wand hängen, sollten Sie sich über die Kabelverlegung Gedanken machen. Je
4.
nachdem, wie die Kabel verlaufen sollen, können Sie sie über die Soundbar verlaufen lassen oder an der Rückseite
herunterhängen lassen. Dies erleichtert die Wandmontage enorm
Richten Sie die Schlüssellochbefestigungen an der Rückseite der Soundbar an den Schrauben aus. Durch leichtes
5.
Kippen der Soundbar lässt sich diese an den beiden Schrauben einhängen. Drücken Sie die Soundbar auf die
Schraubenköpfe und ziehen Sie die Soundbar dann leicht nach unten. Halten Sie die Soundbar so lang fest, bis sie
sicher hält
- 13 -
Loading...