How it Works
Audison
Loading...
APSP G6
operation manual
30 pgs3.66 Mb0
User Manual
1 pgs319.62 Kb0

Audison APSP G6 operation manual

Download
Page 1
APSP G6
INSTALLATION
MANUAL
rev. 1
Page 2
Page 3
INSTALLATION MANUAL
APSP G6 /
Table of Contents
3. TECHNICAL SPECIFICATIONS ...............................................................................................................................................7
6. DISASSEMBLING THE CAR DOOR SILL AND COVERINGS FROM THE RIGHT SIDES ..........................................10
6.1 Removing the rear seat .................................................................................................................................................10
6.2 Removing the right rear wheelhouse cover (5-door version) ................................................................................11
6.3 Removing the right door sill completely ....................................................................................................................12
6.4 Removing the lower cover of the right pillar ............................................................................................................. 13
6.5 Removing the right side covering of the dashboard ............................................................................................... 13
7. DISASSEMBLING THE FRONT DOOR COVERING ...........................................................................................................14
7.1 Removing the front door panel .................................................................................................................................... 14
7.2 Removing the tweeter casing ......................................................................................................................................15
8. PASSING APSP G6 HARNESS CABLES ........................................................................................................................... 16
8.1 Passing the cable in the car radio's casing to the right of the dashboard..........................................................16
8.2 Passing the subwoofer power cable up to the left rear side of the boot ............................................................17
9. INSTALLATION OF SUBWOOFER APBX G6......................................................................................................................18
9.1 Installing the mounting kit ............................................................................................................................................18
9.2 Installing APBX G6 in the car ........................................................................................................................................19
9.3 APBX G6 installation completed ..................................................................................................................................20
10. INSTALLATION OF WOOFERS AP 6.5 G6 .........................................................................................................................21
10.1 Removing original Woofers ..........................................................................................................................................21
10.2 APSP G6 SPEAKER CABLE connection to woofer AP 6.5 G6 ...............................................................................22
10.3 Assembling the woofer into the casing ......................................................................................................................22
11. INSTALLATION OF TWEETER AP 1 SP ..............................................................................................................................23
11.1 Removing the original Tweeters from the casing ....................................................................................................23
11.2 Installing the AP 1 SP MOUNTING KIT ......................................................................................................................23
11.3 Installing AP 1 SP in the casing ...................................................................................................................................24
12. INSTALLATION OF AP 8.9 BIT G6 .......................................................................................................................................25
12.1 Install ASP (Automatic Speaker Presence) ...............................................................................................................25
12.2 APSP G6 HARNESS cable connection to AP 8.9 bit G6 .........................................................................................25
12.3 Positioning AP 8.9 bit G6 ...............................................................................................................................................25
14. REASSEMBLING ALL PARTS ...............................................................................................................................................26
14.1 Reassemble all parts of the vehicle by following the operations described in
the disassembly section in reverse order ......................................................................................................26
15. OPTIONAL ACCESSORIES ....................................................................................................................................................27
15. 3 Bit Play HD ........................................................................................................................................................................27
15.4 OP 1.5 TOSLINK OPTICAL CABLE 1.5 M / 59.05 IN.................................................................................................28
15.5 OP 4.5 TOSLINK OPTICAL CABLE 4.5 M / 177.16 IN ...............................................................................................28
15.6 STA - F/F SOCKET TOSLINK ADAPTER .....................................................................................................................28
15.7 ECK DRC ...........................................................................................................................................................................28
16. TROUBLESHOOTING ..............................................................................................................................................................29
3
Page 4
INSTALLATION MANUAL
APSP G6 /
Introduction
Congratulations for having purchased one of our products. Your satisfaction is the sine qua non that our products must meet: the same satisfaction of anyone who wants to feel the thrill of a car radio. This manual was drawn up to provide important information required to install and use the system.
Before installing the devices, carefully read all the instructions in this manual, and the manuals regarding individual parts included in the relative packages. Failure to comply with these instructions can cause involuntary injury or damage to system's parts or the vehicle.
Warranty
For the warranty conditions, please visit www.audison.eu or contact your specialised Audison centre.
Safe sound
USE COMMON SENSE WHEN LISTENING TO THE RADIO. REMEMBER THAT PROLONGED EXPOSURE TO EXCESSIVE LEVELS OF SOUND PRESSURE CAN DAMAGE YOUR HEARING. SAFETY WHEN DRIVING MUST ALWAYS BE FIRST.
4
Page 5
INSTALLATION MANUAL
APSP G6 /
1
1. PRODUCT DESCRIPTION
APSP G6 was specifically designed for VW Golf 6(*) and comprises:
1. An AP8.9 bit G6 amplifier equipped with bit Drive technology and integrated with 7 drive pre-set dedicated to VW Golf 6(*) designed by the Audison R&D team for “Plug&Sound” performance. The 7 “Drive preset” pre- loaded in the AP8.9 bit G6 memory enables you to use to product without PC connection. Pre-set is chosen based on the user's preferences. AP8.9 bit G6 is equipped with DCC-Direct Cockpit Current technology and is powered directly from the rear connector of the OEM source.
2. An APBX G6 passive closed-box subwoofer, which contains a compact speaker APS 250. The box is specifically designed to be placed on the left side of the boot, and is very compact in size and is fixed to the car without drilling the chassis. The mounting kit and installation manual are in the package.
3. A front two-way system that includes the AP 6.5 G6 woofers, AP 1 SP tweeters and specific crossovers,
adapters to set up OEM for the speakers, connectors, and gaskets for perfect integration with the pillars.
4. A complete set of special cables for the car and kit, designed with Plug&Sound technology to be connected to original car manufacturer connectors, without needing to change the original car cables.
5. A special APSP G6 Harness that draws power of AP8.9 bit G6 directly from the rear connector of the OEM source.
The kit is designed to be installed on a VW Golf 6(*) in less than 2 hours; this time can vary according to the conditions and equipment of the vehicle.
WARNING: Before proceeding with installing, make sure the APSP G6 kit is compatible with the version of your
VW Golf. All the information and images contained in this manual are referred to the left-hand drive 5-door car.
Note: • All kit components have been designed to be attached to the manufacturer's original attachment points on the vehicle.
• Pay special care during the removal and insertion of the speakers' xing rivets.
• Make sure all the gaskets supplied with the speakers are positioned correctly and are working perfectly.
• The connectors are fragile components and must be handled with care.
• After installation and before restarting the system, make sure the equalization of the vehicle's radio is flat.
• Install the kit components by following the instructions to ensure they do not prevent airbags or other safety devices of the car from working correctly.
• Use suitable quality equipment to simplify, accelerate and achieve optimal installation. These installation instructions are updated to revision 01. Additional documents can be downloaded from www.audison.eu.
If there is a malfunction during installation of the kit, check the section regarding “TROUBLESHOOTING” at the end of this manual. If you have consulted the aforesaid section and are still unable to solve the problem, visit www.audison.eu or contact your Audison authorised, specialised centre or ofcial assistance via email: support@elettromedia.it.
*Golf is a registered brand that is property of Volkswagen.
5
Page 6
INSTALLATION MANUAL
QUICK
START
GUIDE
AP8.9
30 A
2. CONTENTS OF THE PACKAGE
APSP G6 /
2
AP 8.9 bit G6
ASP
SETUP CD
AP 6.5 G6
APSP G6 HARNESS
2,6 m / 98.43 in.
x 1
AP 8.9 bit
VELCRO
175 mm x 6.89 in.
x 1
SCREWS
4,2 mm x 50 mm
0.17 in. x 1.97 in.
CAVO USB
1,8 m / 70.87 in.
FUSE 30A
x 1
APGSP G6 SPEAKER CABLE
x 1
QSG WARRANTY HEX KEY
CD 1.0A
x 1
x 1
x 4 x 1x 1
x 1 x 1
AP 6.5 G6 RING
2,5 mm / 0.1 in.
AP 1 SP
295 mm / 11.61 in
645mm / 25.39 in.
x 2
.
WF
TW
x 2
AP 1 SP MOUNTING KIT
x 6
x 2
x 2
AP 6.5 G6 MOUNTING KIT
APBX G6
x 2x 2
AUDISON BADGE
x 10x 8
x 2
DAMPING PANEL
250 x 250 mm / 9.84 x 9.84 in.
x 1
APBX G6 MOUNTING KIT
x 6
x 1
x 1x 1
x 1
6
Page 7
INSTALLATION MANUAL
T
Component
APSP G6 - Front
2 WAY SYSTEM
APBX G6
SUBWOOFER
Size mm (in.)
Woofer 165 (6.5) Tweeter 26 (1)
250 (10)
Power Handling
W (peak) 300 900
W (continuos) 100 300
Impedance Ω 4 4
Frequency Response
Hz 60 ÷ 20k
38-350
Crossover type 2-Way passive Digital
TECHNICAL SPECIFICATIONS
A
3. TECHNICAL SPECIFICATIONS
APSP G6 /
3
3.1 Preset description
PRESET
0
1
7
6
3
5
4
0
1
7
2
6
3
5
4
0
1
7
2
6
3
5
4
0
1
7
2
6
3
5
4
0
1
7
2
6
3
5
4
0
1
7
2
6
3
5
4
0
1
7
2
6
3
5
4
0
1
7
2
6
3
5
4
(default)
LISTENING POSITION
WARNING: Preset “0” contains the input/output congurations dedicated to this speakers system.
2
The “factory default” function loses the pre-loaded preset in “0”. For this reason you must restore correct input/output setting via AP Prima PC software. It is recommended to backup the preset in your PC.
Failure to comply with these recommendations can cause irreparable damage to AP8.9 bit G6 as well as products connected to it. DO NOT CHANGE PRESET WHEN THE PRODUCT IS ON.
Right Hand Drive Acoustic
Right Hand Drive Live
Right Hand Drive Rhythm
POWER - 12V
30A
SPEAKER OUT
1 2 3 4 5
7
6
YOUR SOUND
Overall FLAT
Left Hand Drive Acoustic
Left Hand Drive Live
Left Hand Drive Rhythm
Overall Acoustic
0
1
7
2
6
3
5
4
USB
SUB OUT
OPTICAL IN
1 2 3
INPUTS
4 5 6
OPTICAL SEL.
REM IN
DRC
REM OUT MASTER ENABLE
ASP
UPGRADEPRESETS
OFF ON
0
1
2
345
76
8
DETAILS
This preset only contains standard lters; no equalizations and no time alignments have been applied.
Detailed mid-high frequencies with perfectly balanced bass. Time alignment have been calibrated to ensure the best listening sensation for the driver (Left-hand drive cars).
Crisp mid-high frequencies and really dynamic bass. Time alignments have been calibrated to ensure the best listening sensation for the driver (Left-hand drive cars).
Detailed mid-high frequencies with punchy bass. Time alignments have been calibrated to ensure the best listening sensation for the driver (Left-hand drive cars).
Detailed mid-high frequencies with perfectly balanced bass. Time alignment have been calibrated to ensure the best listening sensation for the driver (Right-hand drive cars).
Crisp mid-high frequencies and really dynamic bass. Time alignments have been calibrated to ensure the best listening sensation for the driver (Right-hand drive cars).
Detailed mid-high frequencies with punchy bass. Time alignments have been calibrated to ensure the best listening sensation for the driver (Right-hand drive cars).
Detailed mid-high frequencies with perfectly balanced bass. Time alignments have been set-up to guarantee the better listening feeling for everybody in the car.
ECHNICAL SPECIFICATIONS
Component
Size mm (in.)
Power Handling
Impedance Ω 4 4
Frequency Response
Crossover type 2-Way passive Digital
W (peak) 300 900
W (continuos) 100 300
Hz 60 ÷ 20k
Notes:
- The AP 8.9 bit G6* is delivered with the selector set on pre-set “7” (Overall – Acoustic).
- You can install the “AP Prima PC Software” program in “Prima Amplier Setup CD”.
* Refer to the operating manual regarding AP8.9 bit for detailed information relating to installation and use of the “AP Prima PC Software”.
All materials are available from www.audison.eu.
APSP G6 - Front
2 WAY SYSTEM
Woofer 165 (6.5) Tweeter 26 (1)
APBX G6
SUBWOOFER
250 (10)
38-350
P8.9 bit OUTPUT CHANNEL MAP
Channel Mode Speaker Power
1-2 3-4 Bridge APSP G6 - Front 2 x 130W RMS @ 4Ω
5-6 Stereo OEM Rear Speakers 2 x 35W RMS @ 4Ω
7-8 Bridge APBX G6 - Subwoofer 1 x 130W RMS @ 4Ω
7
Page 8
INSTALLATION MANUAL
4. CONNECTIONS LAYOUT
APSP G6 /
(DCC)
+ BATT
(Bridge)
4
AP 1 SP Mounting kit
AP 1 SP
AP 6.5 G6
Ch 1/2 (Bridge)
APSP G6
SPEAKER CABLE
Ch 3/4
- GND
AP 1 SP
AP 1 SP Mounting kit
OEM HEADUNIT
APSP G6 Harness
APSP G6
SPEAKER CABLE
AP 6.5 G6
AP8.9 bit G6
Ch 5
Ch 6
NO
ASP
Ch 7/8
(Bridge)
OK
Damping panel
APBX G6
ASP
DRC
REM IN
OPTICAL SEL.
OPTICAL IN
USB
OFF ON
UPGRADEPRESETS
2
3
1
0
567
SPEAKER
POWER - 12V
INPUTS
4
OUT
ASP
30A
REM OUT
MASTER ENABLE
4 5 6
1 2 3
SUB OUT
8
76
1 2 3 4 5
8
Page 9
INSTALLATION MANUAL
APSP G6 /
5. REMOVING THE ORIGINAL CAR RADIO
WARNING: Remove the key from the car's ignition and pull the lever to release the bonnet.
Close the doors and wait for 5 minutes, then open the bonnet and disconnect the negative pole from the car's battery.
5.1 Removing the nishing frame
5
5.2 Removing the 4 fastening screws
Fig. 1
Fig. 2
5.3 Extraction of the original car radio
5.3.1 disconnecting all connectors from the rear.
9
Page 10
INSTALLATION MANUAL
APSP G6 /
6. REMOVING THE DOOR SILL AND COVERINGS FROM THE RIGHT SIDE
WARNING: The procedure shown below describes the right side of the vehicle. Proceed in a similar manner
for the left side.
6.1 Removing the rear seat (Fig. 3 point 1)
6.1.1 Remove the four plastic covers from the Isox anchoring device of the rear seat (Fig. 3 point 2 / 3).
6.1.2 Lift the front part of the seat
6.1.3 Push the bench seat back
(Fig. 3 arrow A) to release the 2 stops (Fig. 3 point 4).
(arrow B) and lift it from the rear, then remove it from the vehicle.
6
2
3
A
B
A
1
4
Fig. 3
10
Page 11
INSTALLATION MANUAL
6.2 Removing the right rear wheelhouse cover (5-door version)
6.2.1 Tip the right backrest forward to access the wheelhouse cover.
6.2.2 Remove the cap from the upper part of the covering
(gure 4) with a plastic lever.
APSP G6 /
6
2
1
6.2.3 Remove the two screws
Fig. 4
(Fig. 5).
Fig. 5
11
Page 12
INSTALLATION MANUAL
6.2.4 Partially remove the gasket from the right door until the wheelhouse covering is free.
6.2.5 Remove nut 1 from bolt 2
6.2.6 Remove the covering from the body
(Fig. 6).
(Fig. 6 point 3).
B
A
B
3
APSP G6 /
6
2
1
6.3 Remove the right wheelhouse completely (Fig. 7)
6.3.1 Lift the front part of the door sill and release the fastening clip.
6.3.2 Release the guide from the lower part of the covering of the central pillar
6.3.3 Lift the rear part of the door sill and release the fastening clip.
6.3.4 Release the guide from the lower part of the covering
6.3.5 Release the tab and extract the safety belt
(Fig. 7 point 2).
(Fig. 7 point 3).
Fig. 6
(Fig. 7 point 1).
1 2
3
Fig. 7
12
Page 13
INSTALLATION MANUAL
6.4 Removing the lower cover from the right pillar (Fig. 8).
6.4.1 Remove the covering with a lever and extract it, as shown by arrows A and B.
6.2.4 Partially remove the gasket from the right door until the wheelhouse covering is free.
B A
APSP G6 /
6
6.5 Removing the right side covering of the dashboard (Fig. 9).
6.5.1 Insert a plastic lever (A) into reference catch 1 and gently force it to the right to
release the fastening clip.
1
A
Fig. 8
Fig. 9
13
Page 14
INSTALLATION MANUAL
APSP G6 /
7. REMOVING THE FRONT DOOR COVERING
WARNING: The procedure shown below describes the right side of the vehicle. Proceed in a similar manner
for the left side.
7.1 Removing the front door panel
7
7.1.1 Remove the door covering grille using a plastic lever, then loosen screws 1, 2, 3 and 4
1
2
4
3
A
(Fig. 10)
Fig. 10
7.1.2 Using a plastic lever, release all the covering clips according to the sequence shown (Fig. 11 ).
7.1.3 Lift the covering by rmly pulling upwards, as shown by arrow C in order to release it
(Fig. 11).
5
B
C
3
1
C
4
2
6
A
Fig. 11
14
Page 15
INSTALLATION MANUAL
7.1.4 Release the door opening control cable (Fig. 12 point 1).
7.1.5 Disconnect all cables from the door's covering.
1
APSP G6 /
7
Fig. 12
7.2 Removing the tweeter casing
7.2.1 Release the tweeter support from the three fastening caps using a plastic lever (Fig. 13 points 1, 2 and 3).
7.2.2 Disconnect the connector
(Fig. 13 points 4).
1
4
3
2
Fig. 13
15
Page 16
INSTALLATION MANUAL
APSP G6 /
8. PASSING THE APSP G6 HARNESS CABLE
WARNING: The procedure shown below describes the right side of the vehicle. Proceed in a similar manner
for the left side.
8.1 Passing the cable from the car radio's casing to the right of the dashboard
8.1.1 Pass sections B, C, and D of cable APSP G6 HARNESS (Fig. 14) from the car radio (Fig. 15) compartment above the glove compartment using a probe
APSP G6 HARNESS
(Fig. 16 A).
8
A
B
C
D
Fig. 14
8.1.2 Insert the cable towards the door sill and connect earth cable D into bolt E (Fig. 16 B).
Fig. 15
Fig. 16 A
E
Fig. 16 B
16
Page 17
INSTALLATION MANUAL
APSP G6 /
8.1.3 Lift the carpet from the floor in point A (Fig. 17) and insert cables C (Fig. 14) under the covering along the slits provided in the carpet. Make sure that both the connectors and power supply cables
exit from the provided slots situated under the front right seat.
- GND
A
8
Fig. 18
Fig. 17 Fig. 20
8.2 Passing the subwoofer power cable up to the left rear side of the boot
8.2.1 Insert the subwoofer's power cable B
(Fig. 14) through passage A (Fig. 17), and run it along the
door sill and through the rear bench seat and proceed until the left wall of the boot cable must exit from the provided slot
(g. 20).
Fig. 19
(g. 18 -19); the
17
Page 18
INSTALLATION MANUAL
APSP G6 /
9
9. APBX G6 SUBWOOFER INSTALLATION
9.1 Installing the mounting kit
9.1.1 Assemble the three brackets of the APBX G6 MOUNTING KIT onto the points provided on the box, strictly
following the instructions reported in the gure
STEP A
Insert one of the two screws but do not tighten it.
Inserire una delle 2 viti ma senza serrarla.
III
(Fig. 21).
II
Tighten the 2 screws.
Serrare le 2 viti.
I
Tighten the 2 screws.
Serrare le 2 viti.
Fig. 21
18
Page 19
INSTALLATION MANUAL
9.2 Installing APBX G6 in the car
APSP G6 /
9
9.2.1 After positioning the DAMPING PANEL brackets and of the box into the anchoring hooks of the boot
9.2.2 Place the box vertically
of the backrest. Then also assemble the second screw and lastly tighten both in order to secure APBX G6
STEP B: from 1 to 6
(Fig. 22 point 5), rotate bracket and insert it into the anchoring hook
(Fig. 22 point 6 A/B).
(Fig. 22 point 1), connect connector (Fig. 22 point 2) and insert
(Fig. 22 points 3 and 4).
III
6
Tighten the 2 screws.
5
a
2
Serrare le 2 viti.
*
b
*
Damping panel
5
3
3
Car hook / Gancio auto
*
If the anchoring hook equipped with the car is not like the one shown in the picture, it is neces-
**
sary to purchase one separately from a Volkswagen dealer. / Nel caso il gancio di ancoraggio,
di cui è quipaggiata la vettura non fosse come quello in foto è necessario acquistarlo separata­mente presso una concessionaria Volkswagen
I
1
*
6
4
II
**
4
Fig. 22
19
Page 20
INSTALLATION MANUAL
9.3 APBX G6 installation completed
APSP G6 /
9
Fig. 23
20
Page 21
INSTALLATION MANUAL
10. AP 6.5 G6 WOOFER INSTALLATION
10.1 Removing original woofers
10.1.1 Disconnect the connector from the original woofer (Fig. 24 point 1).
10.1.2 Remove the 4 rivets that secure the woofer
(Fig. 24 point 2).
1
APSP G6 /
10
2
10.1.3 Place the AP6.5 RING in the points provided, making sure to position the cable gland slot upwards
(Fig. 25 point A) and fasten it using the new rivets supplied in the KIT.
A
Fig. 24
Fig. 25
21
Page 22
INSTALLATION MANUAL
10.2 APSP G6 SPEAKER CABLE connection to woofer AP6.5 G6
10.2.1 Insert the terminals, complying with the polarity (Fig. 26 point A).
A
10.3 Assembling the woofer into the casing
Fig. 26
APSP G6 /
10
10.3.1 Pass the power supply cable through slot A (Fig. 27) and fasten the speaker using the screws supplied with the KIT.
A
Fig. 27
10.3.2 Connect the SPEAKER CABLE to the vehicle's default connector (Fig. 28 point A) positioning the crossover as shown in the photo
(Fig. 28 point B).
A
A
B
Fig. 28
22
Page 23
INSTALLATION MANUAL
11. AP 1 SP TWEETER INSTALLATION
11.1 Removing the original tweeters from the casing
11.1.1 Removing the three plastic seals to release the tweeter (Fig. 29 points A).
11.1.2 Remove the three plastic pins from the point shown in the gure.
(Fig. 29 point B).
APSP G6 /
11
A
B
11.2 Installing the AP 1 SP MOUNTING KIT
11.2.1 Fasten the M3x5 mm screw as shown in the drawing
Fig. 29
(Fig. 30).
Fig. 30
23
Page 24
INSTALLATION MANUAL
APSP G6 /
11.3 Installing AP 1 SP in the casing
11.3.1 Fasten the tweeter with the 3 self-tapping screws 3.5x10 mm supplied with the AP 1 SP MOUNTING KIT (Fig. 31).
11
Fig. 31
11.3.2 Reassemble the tweeter casing onto the door and connect the AP 1 SP cable to the SPEAKER CABLE.
11.3.3 Comply with the cable's polarity
11.3.4 Position the crossover as shown in the photo (Fig. 32 point B).
(Fig. 32 point A).
B
A
Fig. 32
24
Page 25
INSTALLATION MANUAL
OEM HEADUNIT
Ch 1/2 (Bridge)
Ch 7/8
(Bridge)
Ch 5
Ch 6
Ch 3/4
(Bridge)
+ BATT
(DCC)
- GND
AP 6.5 G6
APBX G6
Damping panel
AP 6.5 G6
AP8.9 bit G6
AP 1 SP
AP 1 SP
AP 1 SP Mounting kit
APSP G6 Harness
APSP G6
SPEAKER CABLE
APSP G6
SPEAKER CABLE
12. AP8.9 BIT G6 INSTALLATION
12.1 Install ASP (Automatic Speaker Presence)
APSP G6 /
12
12.1.1 Install the ASP module in the provided place
OPTICAL IN
1 2 3
INPUTS
4 5 6
OPTICAL SEL.
REM IN
REM OUT MASTER ENABLE
DRC
ASP
(Fig. 33).
ASP
12.2 APSP G6 HARNESS cable connection to AP8.9 bit G6
12.2.1 In sequence, connect: A. Earth cable (black).
B. Power supply cable (red). C. Outputs connector. D. Inputs connector.
12.2.2 Isolate the cables from services that are not used
OK
(Fig. 35).
ASP
NO
Fig. 33
POWER - 12V
B
SPEAKER OUT
30A
1 2 3 4 5
A
USB
OPTICAL IN
UPGRADEPRESETS
OFF ON
0
1
7
2
6
345
76
8
SUB OUT
1 2 3
C
INPUTS
4 5 6
OPTICAL SEL.
REM IN
DRC
REM OUT MASTER ENABLE
D
OK
ASP
ASP
NO
ASP
Fig. 34
12.3 Positioning AP8.9 bit G6
12.3.1 Position AP8.9 bit under the right seat, fastening it with the VELCRO tape supplied
(Fig. 36).
Fig. 35
Fig. 36
25
Page 26
INSTALLATION MANUAL
13. CONNECTION OF THE APSP G6 HARNESS CABLE TO THE ORIGINAL CAR RADIO
13.1 Connect the APSP G6 HARNESS cable, as shown in the gure (Fig. 37)
APSP G6 /
13/14
Fig. 37
14. REASSEMBLING ALL PARTS
14.1 Reassemble all parts of the vehicle by following the operations described in the disassembling sections.
WARNING: Be careful of the overall dimensions and fastening of new cables installed.
26
Page 27
INSTALLATION MANUAL
15. OPTIONAL ACCESSORIES
15.1 DRC DIGITAL REMOTE CONTROL
DRC is a digital interface between the bit processors and the user. A DRC assembled on the dashboard of the vehicle with AP bit processor, provides:
- The option to select between the main and aux inputs
- Control the general volume, subwoofer volume,
balance and fader
- The option to select between 2 memory prsets dened by the user for equalizer and crossover alignment settings.
15.2 DRC-MP DIGITAL REMOTE CONTROL
The new Audison DRC MP (Digital Remote Control Multimedia Play) is compatible with all Audison electronics equipped with an AC Link bus. Its slim profile combined with the supplied holder makes it easier to install it in the best position of your car. The new Joystick, “Rubber Touch” finish for maximum movement control in the four direction axis enables “DRC Settings” menu adjustment and “Navi Command” navigation if equipped with an Audison bit Play HD with video output connected to a monitor. The matt black finish and the option to select amongst forty-two different colours of the keyboard enables easy integration of DRC MP with the car's dashboard. The new display with white characters is equipped with a sensor that automatically adjusts the brightness of the characters according to the light in the driver and passenger compartment, and is legible from any angle of vision.
APSP G6 /
15
15.3 Bit Play HD
HD bit play and Play HD SSD bit are high-resolution multimedia servers specifically developed for car audio systems. Connecting the optical output of Play HD bit to an Audison processor or amplifier with digital input creates a Full DA system able to obtain new quality reference that goes beyond CD standards as a result of the possibility of reproducing FLAC audio files that are coded up to 24 bit/96 kHz. To enable users who do not want to manage external hard drives, Play HD SSD bit is equipped with an internal SSD 2.5” unit of 240 GB, which is insensitive to vibrations and jolts that occur whilst driving, thanks to solid state technology and a mechanical casing with specifically designed damping. SSD is also much faster than a traditional hard disk and offers maximum speed to access multimedia content. If provided with video input, it is possible to connect the Play HD bit and Play HD SSD bit to the source or an external monitor via HDMI or compound video output and view the native interface of the multimedia server to control navigation functions and multimedia files directly through the remote control and access the device's configuration. Audison R&D department has designed an App for Apple and Android devices that enables you to connect the smartphone to Play HD bit and Play HD SSD bit via Wi-Fi and use it as a remote control manager of the multimedia catalogue without having to connect the reader to an external monitor.
27
Page 28
INSTALLATION MANUAL
15.4 OP 1.5 TOSLINK OPTICAL CABLE 1.5 m / 59.05 in.
TOSLINK optical cable with terminations for S/PDIF digital audio signals.
Cable length: 1.5 m / 59.05 in.
15.5 OP 4.5 TOSLINK OPTICAL CABLE 4.5 m / 177.16 in.
TOSLINK optical cable with terminations for S/PDIF digital audio signals.
Cable length: 4.5 m / 177.16 in.
15.6 STA - F/F SOCKET TOSLINK ADAPTER
Optical adapter for TOSLINK optical cable extensions with terminations.
APSP G6 /
15
15.7 ECK DRC
DRC cable extension kit for installation on especially long vehicles. The total length of the cable supplied by default together with the
extension is 6.5 m.
For all models
28
Page 29
INSTALLATION MANUAL
16. TROUBLESHOOTING
The AP8.9 bit G6 logo is off.
The car radio starts by no sound is heard
The AP8.9 bit G6 logo ashes blue,
blue/red, red.
The AP8.9 bit G6 logo is on correctly. The volume is too low.
FREQUENTLY ASKED QUESTIONS
Check the power supply fuse. If necessary, replace it with a new one of the same type and value. Check for the presence of 12V on the power supply terminals. Make sure connector C chap. 12 has been inserted correctly (Fig. 34)
The “Logo Status” indicates the operation status of the product and any malfunctions. Refer to the operating manual of AP8.9 bit, sec. 4.12 or sec. 4.13. The user manual is loaded into the CD-ROM included in the box. It’s also available form www.audison.eu web site.
APSP G6 /
16
The sound is not natural and does not come from all speakers
Incorrect setting of volume/balancer/ fader controls.
The connections are correct but are not secured.
Adjust the default source controls.
Check the connections and secure them.
29
Page 30
All specications reported herein are subject to change without any prior notice
PART OF ELETTROMEDIA
62018 Potenza Picena (MC) Italy T +39 0733 870 870 - F +39 0733 870 880 www.elettromedia.it
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use