Audiovox VOD122 User Manual

®
VOD122
12.1" OVERHEAD LCD MONITOR WITH DVD PLAYER
Installation Guide
Important Notice
An LCD panel and / or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.
Important Note
The VOD122 incorporates three new features:
1) A wireless FM Modulator
2) Capability to add an optional plug-in TV tuner (Audiovox P/N PODTVT2)
3) Snap on Covers with matching Trim Rings (Shale and Pewter).
Select the color that matches the interior trim.
Please be advised that the wireless FM modulator will perform well in most applications. However, in certain applications the quality of the wireless signal may be less than optimal, resulting in static or strong local station bleed thru. If this is the case, an optional relay box is available. The Audiovox part number is SIRSWB and it plugs into the 1/8" jack located next to the FM antenna on the side of the chassis. This relay box is installed between the vehicle antenna and the car radio to provide the best possible FM reception of the DVD player audio. When the SIRSWB is installed it is recommended that the wireless FM antenna that is plugged into the printed circuit board next to the 3.5mm jack be unplugged.
MATERIALS INCLUDED IN THIS PACKAGE:
1) VOD122 TV / Video Monitor with DVD – (1pc)
2) 12 Pin Power / Signal harness (P/N 112-3483) – (1pc)
3) 2 Pin Power Wire Harness with choke (P/N 112B3143) – (1pc)
4) 9 Pin ~ 3 RCA Jack Pigtail (P/N 112-3682) – (1pc)
5) Hardware Package Screws ISO 3 x 6mm Long – (10pcs) #8 x 3/8" Self Drilling Screws – (4pcs) M5 Screws (4pcs)
6) Trim Ring (Shale) – (1pc), Pewter – (1pc)
7) Remote Control (P/N 136-4196) – (1pc)
8) Wireless Game Controller (P/N 136-4197) (1pc)
9) Mounting Bracket (P/N 108-3930) – (1pc)
10) Pry Tool – (1pc)
11) Snap On Cover (Shroud) ~ Shale – (1pc), Pewter – (1pc)
12) Snap On Cover (Screen Back Cab) ~ Shale – (1pc), Pewter – (1pc)
13) Wireless Headphone (P/N MVIRHS) – (2pcs)
Optional Accessories
14) PODTVT2 TV Tuner – (1pc) (Optional)
15) SIRSWB Relay Box (P/N 112C3159) (1pc) (Optional) – See important note on previous page
1
8
9
2
3
4
10
14
11
5
12
(Optional)
6
13
15
(Optional)
TOOLS REQUIRED:
#2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim ring if used) Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to vehicle) DVD Movie (to verify system operation after installation)
7
1
Installing The Snap On Covers
1. 3.2. 4.
Housing
Snap On Cover
(Shroud)
1 Pewter, 1 Shale
Place the pod on a soft surface to avoid damaging the plastic.
Snap On Cover
(Screen Back Cab)
1 Pewter, 1 Shale
Pry Tool
Installing The Shroud
catch catch
(A)
Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place.
Installing The Screen Cover
(B)
Open the screen and hook the two tabs “B” on the bottom edge of the screen. Snap the opposite side over the hinge
(B)
2
Removing The Snap On Cover (Shroud) From The Housing
Work on a soft surface to avoid damaging the plastic. Insert the supplied pry tool between the Housing and Snap On Cover (Shroud), then press the pry tool to release the
Snap On Cover (Shroud).
1 2 3
Removing The Snap On Cover (Screen Back) From LCD The Housing
Insert the supplied pry tool between the Housing and Snap On Cover (Screen Back), then press the pry tool to release the Snap On Cover (Screen Back).
4
6
5
7
3
Loading...
+ 9 hidden pages