Audiovox VOD10PS2 User Manual

VOD10PS2

10.2" OVERHEAD LCD
MONITOR WITH

SONY PS2 PLAYER

MENU/ENTER

OPERATION

MANUAL

128-8667A

Important Notice

Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side

curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or
D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from
fully deploying which can result in personal injury to vehicle occupants. If you have any questions regarding wire routing in a vehicle,
please contact Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to
the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection
point and the mobile video product.

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used
for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television
reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is
in “park” or when the vehicle's parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the
parking brake is not applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator
of the motor vehicle.

Warnings

•

Do not use any solvents or cleaning materials when cleaning the video monitor.

•

Do not use any abrasive cleaners, they may scratch the screen.

•

Use only a lightly dampened lint free cloth to wipe the screen if it is dirty.

•

Lock the LCD screen in the fully closed position when not in use.

•

Before putting on headphones always adjust the volume setting to the lowest position.

•

Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome lights, if left on, can drain
the vehicle's battery.

•

Do not put pressure on the screen.

•

Caution children to avoid touching or scratching the screen, as it may become dirty or damaged.

Licensed under one or more of the following patents: Patent NOS. 5,775,762; 5,927,784; and 6,678,892

PlayStation 2 is a registered trademark of Sony CorporationÒ

Congratulations

Congratulations on your purchase of the AUDIOVOX
VOD10PS2 Player with Drop-Down Video / Monitor. The
VOD10PS2 has been designed to give you and your family
many years of video entertainment in the mobile
environment. Please read the directions that follow to
familiarize yourself with the product to ensure that you obtain
the best results from yourequipment.

Please note:

owner's manuals for each component in your system to
obtain a full understanding of eachcomponent's operation.

Installation options vary, see the individual

FEATURES

• 10.2” TFT (Thin Film Transistor) Active Matrix LCD
(Liquid Crystal Display) Monitor

• SONY PlayStation2 game console

Built-in

•SONY

2 Wireless Game Controllers

•

Full Function Remote Control

• OSD (On Screen Display) for Control of Picture Quality
and Functions

Infrared Transmitter for IR Wireless Headphones

•

PlayStation2

Safety Precaution

For safety reasons, when changing video media it is
recommended that the vehicle is not in motion, and that you
do not allow children to unfasten seat-belts to change video
media or make any adjustments to the system. System
adjustments can be accomplished using the remote control,
while seat-belts remain fastened. Enjoy your AUDIOVOX
entertainment system but remember the safety of all
passengers remains the number one priority.

• 2 wireless IR headphones

• PS2 V1, AUX)

Audio/Video Source Inputs ( , A

• A/V output via RCA pigtail

• Dome Lights with 3-Position Switch

•

Built-in 16 Channel Frequency Wireless FM Modulator

•

Screen Mode Selection (4:3, 16:9)

•

Backlit Controls

•s SONY Games

Play DVD, CD and

3

PlayStation2

QS G

UICK TART UIDE

1. Insert batteries into the game controllers and the remote control ame controller transceivers are
preinstalled when the unit is shipped.

2. Turn the vehicle on. Running this unit on battery power (accessory key setting) will drain the battery.

3. Press the screen release button to lower the LCD screen. Swing the screen back to allow the PlayStation2 to drop

down.

4. Push the release button to drop down the PlayStation2

5. Press the (open) button on the PlayStation2 to open the isc cover.

6. Insert a DVD or game onto the spindle and press gently to seat the disc on the spindle.

7. Close the disc cover on the by pressing down gently on the center of the cover.

8. Return the PlayStation2 to its docked position.

9. Turn the VOD10PS2 on by pressing the power button.

NOTE:

10. If a DVD is played press the PLAY key on the remote control, or the “X” key on the game controller or the

Menu/Enter key on the front of the overhead unit.

PlayStation2 .



PlayStation2

If a blue screen is present, press the green RESET key on the remote control or the

PlayStation2 . G

PlayStation2 d

PlayStation2

PlayStation2.

4

QUICK START GUIDE (Cont)

11. When using the wireless headphones install the batteries in each headphone. Turn the volume to minimum before

turning them on. Once they are turned on, place them on your head (pay attention to R/L earpieces) and slowly
adjust the volume to a comfortable listening level.

12. When listening to the system over the vehicle radio:

a. Using the remote control:

i. to turn on the FM modulator by pressing FMM ON/OFF
ii. Select an FM frequency by pressing FMM Select.
iii. Tune the vehicle radio to the FM frequency selected.

b. Using the MENU/ENTER Key on the front of the unit:

i. Press MENU/ENTER.
ii. Use the (down) key to highlight FMM, press MENU/ENTER.
iii. Use the (down) or (up) key to select FMM ON.
iv. Press MENU/ENTER to select FMM ON.
v. To select the frequency press MENU/ENTER.
vi. Use the (down) key to highlight FMM and press MENU/ENTER.
vii. Use the (down) key to highlight FMM SELECT and press MENU/ENTER.
viii.Use the (down) (up) (right) or (left) keys to select an FM frequency.

NOTE .

( : For best sound quality select an FM Frequency that is not used in the area you will be driving )
ix. Press MENU/ENTER to set the FM frequency.
x. Tune your vehicle radio to the frequency just set in the steps above.
xi. Adjust the volume of the vehicle radio to a comfortable listening level.

q
qp

q
q

qpu t

5

QUICK START GUIDE (Cont)

U

sing the Control Panel

To access the Control Panel press the dark gray DISPLAY or dark gray SELECT button. The Control Panel (Below) can be
used to navigate the DVD disc. Refer to figure below:

Pressing the dark gray DISPLAY or dark gray SELECT button again will cause the Control Panel to change its position on
the screen. Pressing the DISPLAY or SELECT button a third time will turn off the Control Panel. Use the dark directional
buttons ( to select an icon. When the desired icon is selected, press the button.

)qput

NOTE: .

For complete instructions regarding the functions provided by the Control Panel refer to the PlayStation2 User’s Guide.

The Control Panel may appear at the end of some DVD movies

6

CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW)

1. SOURCE Button (S)

Use to selectthe sources: PS2, AV1 and AUX.

10

11

12

MENU/ ENTER

1234567

2. CURSOR Buttons ( )

Use these buttons to access menu selections on the screen.

3. MENU/ENTER Button

Use this button to access SYSTEM MENU and select system

pqt u

menu items.

4. Infrared Transmitter and Sensor

13

Transmits audio to wireless headphones, allows the remote
control to operate the unit and to control otheraccessories in the

14

8
9

MEMORYCARD MEMORYCARD

FORCELINK

FORCELINK

RESET I/

15

16

system.

5. POWER Button ( )

Used to turn the system on/off (standby).

6. Dome Lights

Provide additional interior illumination.

7. Three Position Dome Light Switch
ON

- Turns on the dome lights. (Do not leave switch on when

vehicle is off.)

OFF

- The dome lights will not turn on in this position.

AUTO

- Automatically switches on the dome lights in
conjunction with the vehicle's interior illumination.

8. PlayStation2 CONSOLE

9. MEMORY CARD SLOT 1 & MEMORY CARD SLOT 2
(Memory Cards not supplied)

10. PS2 WIRELESS CONTROLLER TRANSCEIVERS
(Transceivers supplied)

7

11. LCD Panel

12. Screen Release

Press to release the screen.

13. LCD Cut Off Switch

Used to turn off the LCD backlit when the LCD is in the closed
position.

14. OPEN

Push to open the tray.

PlayStation2

CONTROL FUNCTION DESCRIPTION
(SIDE VIEW)

1 2 3 4

L

R

VIDEOAUDIO

15. OPEN ( )



The disc tray opens.

16. RESET ( )

ON/Standby and RESET indicator.

1. HEADPHONE JACK

For wired headphone with a 1/8” (3.5mm) plug.

2. Auxiliary Audio Right Input

3. Auxiliary Audio Left Input

4. Auxiliary Video Input

8

Back View

MAIN FUNCTION OPERATIONREMOTE CONTROL OPERATION

Battery Cover

Battery Installation

Before attempting to operate your Remote Control, install the
batteries as described below.

1) Turn the Remote Control face down. Using your finger, slide
the battery cover off in the direction of the arrow.

2) Install Two “AAA” batteries. Make sure that proper polarity
(+ or -) is observed.

3) Align the cover tabs with the remote control and slide the
cover until it locks.

The remote control is designed to operate the unit. It is not a
universal remote control and will not control equipment from other
manufacturers.

M1
M2
M3

M4

M5
M6
M7

M8

P10

P11

P12

P13

P14
P15

P16
P17
P18

P19
P20

OPEN/

P1

P2
P3

P4
P5

P6
P7

P8

CLOSE

AUDIO SHUFFLE

ANGLE

PROGRAM

SUBTITLE REPEAT

SLOW

SCAN

CLEAR

PREV NEXT A-B

P9

DISPLAY TOP MENU

14253

89

7

0

PAUSE STOPPLAY

MENU

RESET

TIME

RETURN

P36

P35

6

P34
P33

P32
P31

P30
P29

P28
P27

P26

ENTER

P25

P24
P23

P22
P21

M11

M10

M9

MUTE

SYSTEM

MENU

SOURCE

DISPLAY

STARTSELECT

R3

VOLUME

ENTER

PIX

L1 L3

L2 R2

FMMON/OFF

FMMSELECT

IRON/OFF

R1

DVD /PLAYSTATION

9

REMOTE CONTROL FUNCTIONS

The remote control is divided into two sections, Dark Gray buttons on the top, which control the built-in PlayStaion2 and Light Gray

buttons on the bottom of the remote control, that control the other functions of the unit.

PLAYSTATION CONTROLS (P1-P36) (Dark Gray Buttons)

NOTE:

P1. OPEN/CLOSE

P2. AUDIO

P3. SHUFFLE

P4. ANGLE

P5. PROGRAM

P6. SUBTITLE

P7. REPEAT

PlayStation2 controls (referto the SONYPlayStation2 manual for details).

Not used onthis model.

Displays and changesDVD audio options.

Starts playbackof titles or chapters in random order.

Displays and changes DVD viewing angle options.

Displays theProgram Setup screen.

Displays and changesDVD subtitle options.

Selects repeated playbackof all thetitles on the disc, orone title orchapter.

10

P8. SLOW ( / )

Changes to slow-motionplayback. (Forward orReverse)

P9. SCAN ( / )

Fast forwards orfast reverses playbackon the screen to locatea particular scene.

P10. PLAY

Starts playback.

P11. DISPLAY

Displays the ControlPanel of thePlayStation2.

P12. TOP MENU

Displays the disc menu of DVD-Video discs. The content varies from disc to disc.

P13. BUTTON: DVD MENU

Selects the item to be changed.

P14. ENTER

Executes the item selected on the DVD disc menu or the on-screen Control Panel.

P15. BUTTON: TITLE MENU

Selects the title to be played.

P16. DIRECTIONAL BUTTONS: CURSOR CONTROL

Use these buttons to access the menu selection on the screen.

P17. L3 BUTTON

Displays Subtitle Options to select the subtitle language and/or turn it on or off.

11

P18. L1 BUTTON

Previous ( ), press to return to the previous chapter or track.

P19. L2 BUTTON

Search ( ) using fast reverse or fast forward playback.

P20. SELECT

Displays the control panel of the PlayStation2.

P21 START

Press to Play/Pausedisc playback.

P22. R2 BUTTON

Search ( ) usingforward playback.

P23. R1 BUTTON

Next ( ) press to skip to the next chapter or track.

P24. R3 BUTTON

Displays Audio Options, press the language changes.

P25. BUTTON: ENTER

9

:

P26. BUTTON: CANCEL / (Stop)

P27. MENU

Displays the disc menu of DVD-Video discs. The content of the menu varies from disc to disc.

P28. RETURN

Returns to the previously selected screen within the disc menu of DVD-Video discs.

<

12

P29. PAUSE

Pauses and resumes playback.

P30. STOP

Stops playback.

))

P31. PREVIOUS ( / NEXT (

Returns to thebeginning of thecurrent or previous chapter/Skips tothe beginning ofthe next chapter.

P32. A-B REPEAT

Specifies a scenefor playback andstarts playback of the scenethat has beenset.

P33. CLEAR

Clears selected numbers or playback modes.

P34. TIME

Displays the current title or chapter number and the elapsed or remaining time.

P35. NUMBER 0~9

Used to select numerical items displayed on the screen.

P36 STANDBY / RESET

Used to turn on, reset, and set the PlayStation2 console in standby mode. On :Press Once. Reset :Press for about one second.

Standby mode :Press and Hold down for more than three seconds.

9:

OVERHEAD MONITOR CONTROLS (M1-M11) (Light Gray Buttons))

M1. POWER

Press this button to turn the unit ON and OFF.

13

M2. MUTE

Press this button to mute the audio. Pressing the button again restores the sound to the previously set level.

M3. FMM ON/OFF

Turns the wireless FM Modulator ON or OFF.

M4. SYSTEM MENU

Allows the user to access the main system menu for picture controls, FM Modulator Select, screen mode etc.

M5. FMM SELECT

Selects the FM Modulator Frequency.

M6. SOURCE

Each time the button is pressed, the audio/video source will change: PS2, AV1 and AUX.

M7. IR ON/OFF

Turns the Infrared Transmitter powerON/OFF for IRWireless Headphones.

M8. DISPLAY

Press to display OSD information.

M9. ENTER

Used to execute a selected setting or menu option.

M10. CURSOR BUTTON ( )

Use these buttonsto access systemmenu selections on the screen.

M11. VOLUME ( – PIX + )

Each time this button is pressed, the OSD will display the “adjustment bars” for BRIGHTNESS, CONTRAST, COLOR or TINT.
Once the desired adjustment bar is displayed, use the (" " / " ") buttons to adjust the setting. The display will automatically

turn off if no adjustments are made after 6seconds, or if any other button is pressed.

pqt u

+–

14

WIRELESS CONTROLLER (2.4GHz)

Carefully read the information before use. For detailed connection and
usage methods, refer to the Owner’s Manual for the PIayStation2 system.

HOW TO USE

Battery Installation:

The wireless controller uses two “AA” batteries.

1. Turn your controller upside down and remove the lid on the bottom by pressing against
the lip and pulling the lid away.

2. Insert the batteries as indicated in the controller.

3. Once the batteries are inserted, put the lid back in its place and cover the batteries.

Safety Precaution: Follow the battery manufacturer’s instructions as well as
there important safety tips. Do not open or mutilate batteries as they might leak
dangerous chemicals.

T

he wireless transceivers are pre-installed in the controller ports on your PlayStation2 system.

Turning On the Controller:

1. Turn on your PlayStation2 system. Press the green reset button on the remote control if
the

PlayStation2 does not come on when the main unit is turned on.

2 Place the ON/OFF switch for your controller, which is located between the dual analog

joy sticks, to ON. The POWER LED will illuminate green.

3. Once the controller has been powered on, the PlayStation2 will recognize the wireless
controller. The MODE LED indicator will illuminate red on the wireless controller, indicating
the connection between the wireless controller and the receiver. The green Rx LED on the
PlayStation2 transceiver will illuminate a steady green.

15

ON/OFF Switch

POWER LED

MODE LED

Sleep Mode:

Your controller will automatically go into Sleep Mode after approximately three minutes
if not used. The MODE LED indicator will go off. To reactivate the controller, you have
a choice to press the START button or press down on one of the joy sticks on the controller.
Your controller will automatically synchronize with the receiver in the PS 2 unit.

Turning Off the Controller:

Place the ON/OFF switch on the controller to OFF if it will not be used for
a long period of time to preserve battery life.

If Your Controller Does Not Synchronize:

1. If the red MODE LED indicator on your wireless controller does not activate, switch the controller off, wait three seconds, and switch it
back on using the ON/OFF switch on the front of the controller.

2. If this does not activate the red MODE LED, switch the controller back off. Turn off your PlayStation2 console and remove the wireless
receiver(s). After this is done, reconnect the receivers, turn on your PlayStation2 console and turn your controllers back on.

3. If this does not activate the red MODE LED, check the batteries and replace as needed.

4. After checking and/or replacing the batteries, repeat step 2 for activation.

Low Power Warning Function:

Under low battery conditions, the MODE LED will flash and the vibration motors will automatically turn off.

Vibration:

Games with the vibration feature will enable the vibration in the controller. Vibration can not be disabled.

START button

Joy Sticks

Safety Precaution: Stop using this unit immediately if you begin to feel tired or if you begin to feel discomfort or
pain during use. Do not use the vibration function if you have an ailment or injury to the bones, joints or muscles
of your hands or arms.

16

SYSTEM MENU ADJUSTMENT

The System Menu contains features and options that let you customize your system to change the screen mode display, OSD language
and source default.

1) Press the MENU/ENTER button on unit to enter System Menu, the main page of the system menu will appear on screen.

2) Use the cursor buttons or to select the desired item in the main page and press the MENU/ENTER button to select. (Items

selected in the menu will have a green background)

3) The sub menu will appear on screen.

4) Use the cursor buttons or to select an item in the sub menu and then press the MENU/ENTER button to select.

5) Use the cursor buttons or to adjust picture control and press the MENU/ENTER button to confirm setting.

6) Press and hold the MENU/ENTER button to exit System Menu.

NOTE: System Menu can be controlled via unit and remote control. Press the SYSTEM MENU button for access. (Items selected in the
menu will have a green background)

PICTURE CONTROL (REMOTE CONTROL)

When watching a DVD or playing a game, the picture quality can be adjusted to suit your personal taste.

1) Press the SYSTEM MENU button on the remote control, the SYSTEM MENU will appear.

2) Highlight PICTURE CONTROL using the light gray or buttons and press the light gray ENTER button. The PICTURE CONTROL

menu will appear.

3) Use the light gray or buttons to highlight the picture control to be changed and press the light gray ENTER button. The control

setting for that picture control will appear on the screen.

pq

pq

tu

pq

pq

SYSTEM MENU

PICTURE CONTROL
FMM

OSD LANGUAGE
SOURCE DEFAULT PS2
SCREEN MODE

PICTURE CONTROL CONTRAST16

BRIGHTNESS
CONTRAST

COLOR
TINT
RESET

17

4) Use light gray or buttons to change the picture control setting.

tu

5) To change another picture control setting press the SYSTEM MENU button and select another picture control using the light gray

or buttons. Repeat step 4 to change the picture control setting.

pq

6) To reset the picture control settings to the factory default settings, enter the picture control menu and use the light gray button to

q

highlight RESET and press the light gray ENTER button.

NOTE:

The light gray PIX control and light gray VOLUME and + buttons on the remote control can also be used to adjust the picture
control settings. When using this method highlight RESET and press the or + button to reset the picture controls to factory default
settings.)

FMM

FMM ON/OFF options- Turns the wireless FM Modulatoron or off.

1) Press the SYSTEMMENU on theremote control, the following screenwill appear:

SYSTEM MENU

PICTURE CONTROL
FMM

OSD LANGUAGE
SOURCE DEFAULT PS2
SCREEN MODE

2) Use the light gray (down) arrow on the remote control to highlight FMM as shown below:

q

SYSTEM MENU

PICTURE CONTROL
FMM

OSD LANGUAGE
SOURCE DEFAULT PS2
SCREEN MODE

18

3) Press the light gray ENTER button on the remote control and the following screen will appear:

FMM

FMM ON
FMM OFF

FMM SELECT

4) Use the light gray (up) or (down) arrow on the remote control to highlight FMM ON and press the light gray ENTER button to

pq

turn the FM Modulator on.

FMM SELECT

1) Repeat steps 1 through 3 above and highlight FMM SELECT
2 Use the light gray (down) arrow on the remote control to highlight FMM SELECT and press the ENTER button, the following

)

screen will appear

3 Use the light gray (up) (down) (left) (right) buttons on the remote control to select a frequency not used by a radio station

)

q

.

pq t u

FMM SELECT

88.1 MHz

88.3 MHz

88.5 MHz

88.7 MHz

88.9 MHz

89.1 MHz

89.3 MHz

89.5 MHz

89.7 MHz

89.9 MHz

90.1 MHz

90.3 MHz

90.5 MHz

90.7 MHz

90.9 MHz

91.1 MHz

in the area. Press the light gray ENTER button to select the highlighted frequency.

: The menu will time out after a short period, or press the SYSTEM MENU button to turn off the menu.NOTE

19

OSD LANGUAGE

This allows the user to select the language for the on-screen display. The user can either select English, Spanish, French, German for the
OSD language.

SYSTEM MENU

PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT PS2
SCREEN MODE

OSD LANGUAGE

ENGLISH
SPANISH
FRENCH
GERMAN

SOURCE DEFAULT PS2

This allows theuser to setthe system default source toPS2 (via System Menu).

NOTE:

If selected default source is set to PS2 every time the unit’s power is cycled with the source set to something other then PS2, the unit will power

•

up and automaticallyswitch the sourceover to PS2

Unit will beset to LastSource on as the defaultmode of operation.

•

• Selection ofSource default canonly be madefrom within the system menu.

SYSTEM MENU

PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT PS2
SCREEN MODE

SOURCE DEFAULT PS2

ON
OFF

SCREEN MODE

This allows the user to change the screen format (aspect ratio 4:3, 16:9).
To select the screen aspect ratio format highlight SCREEN MODE and press MENU/ENTER button to enter the submenu. Then press the
Cursor button or to select from 4:3 or 16:9. Press MENU/ENTER button to confirm the setting.

pq

SYSTEM MENU

PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT PS2
SCREEN MODE

SCREEN MODE

4:3
16:9

20

TURNING THE UNITON OR OFF

1. Pushing in theScreen Release buttonwill unlock the LCD screenand it willdrop down slightly. Pivot thescreen downward untila
comfortable viewing angleis reached. The hinge frictionwill hold the screen inposition while thesystem is in use.

2. Pressing the powerbutton* on theunit or the remote controlwill turn thesystem on and off. When in usethe internal backlighting will
illuminate the controls.

3. After the unithas been turnedon and is displaying apicture, adjust theviewing angle, by pivoting thescreen to optimizethe picture quality.

4. Remember to turnthe unit off and pivot the LCDto the lockedposition when notin use.

Power

ON/OFF

Button

Remote Sensor

Infrared Transmitter

MENU/ENTER

Screen Release

21

OVERHEAD DOME LIGHTS

The Dome Lights integrated into the unit are controlled by a three position slide switch. Sliding the switch to the ON position will turn
the lights ON. The OFF position will prevent the lights from turning ON with the vehicle's interior lighting, and the auto position will allow the
lights to turn ON and OFF with the vehicle's interior lighting. Refer to the Installation Guide for wire connections. Do not leave the vehicle
unattended with the dome light switch in the ON position, as this could result in a discharged battery.

ACCESSORIES

WIRELESS HEADPHONES

The unit includes a built-in infrared transmitter for use with the supplied wireless headphones. The headphone volume is adjusted using
the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the
transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your wireless
headphones.

WIRED HEADPHONES (OPTIONAL)

There is one 1/8” headphone jack on the unit that can be used with any standard wired stereo headphones with a 1/8” plug. This jack is
controlled by the volume up/down buttons on the remote control or the (left) (right) buttons on the overhead.

tu

22

SOURCE FEATURE

AV1

The AV1 input may be connected to a external video source, video game system, or other audio / video devices. To access the
audio / video inputs, turn the unit on and press the S (source) button or the Source button on the remote control until "AV1" is
displayed on the screen. Turn the video source component on with its power button or remote control and it is now ready to play
the audio and video signals from the source connected .

NOTE: The AV1 source is available only ifpre-installed during yourvideo product installation.

AUX

The AUX input (located on th right side of the unit) may be connected to a external video source, video game system, or other audio / video
devices. To access the audio / video inputs, turn the unit on and press the S (source) button or the Source button on the remote control until
"AUX" is displayedon the screen.

PS2

Press the sourcebutton until thescreen displays PS2.
Press ( ) RESET on unit/remote control toturn ON the PS2 Console.

23

TROUBLESHOOTING

PROBLEM

IR remote inoperative

Disc won't play

Play starts, but then stops immediately

No sound or distorted sound

Can’t advance through a movie

SOLUTION

Verify that the batteries in the remote are fresh.
Verify that the remote sensor eye is not obstructed.

Insert a discwith the labelside facing up.
Check the type of disc you put into disc tray. This PS2 only plays PS2 GAMES, DVDs,

audio CDs.
Both the unit and the disc are coded by region. If the region codes don’t match, the
disc can’t beplayed.
Make sure screensource is setto PS2.

The disc is dirty. Clean it.
Condensation has formed. Allow player to dry out.

Make sure your DVD is connected properly. Make sure all cables are securely
inserted into theappropriate jacks.
Make sure the Modulator is ON and the Frequency selected on the unit matches
the frequency set on the radio.
Make sure that unit is using Single Channel Headphones or Dual Channel
Headphones set to channel A.
For wireless headphones make sure the batteries are fresh.

It can’t advance through the opening credits and warning information that appear

at the beginning of movies because the disc is programmed to prohibit that action.

24

PROBLEM

SOLUTION

Not allowed at the moment

Picture is distorted

No forward or reverse scan

The feature or action cannot be completed at this time because:

1. The disc’s software restricts it.

2. The disc’s software doesn’t support the feature (e.g., angles)

3. The feature is not available at the moment.

4. 4 title or chapter number that is out of range.

The disc might be damaged. Try another disc.
It is normal for some distortion to appear during forward or reverse scan.

Some discs have sections that prohibit rapid scanning or title and chapter skip.
If you try to skip through the warning information and credits at the beginning of a
movie, you won’t be able to. This part of the movie is often programmed to prohibit
skipping through it.

Service and Repair

Warranty on all components in this system ( VOD10PS2, Remote Control, Game Controllers and built-in Sony PlayStation2) is handled
by Audiovox Electronics Corporation. For service call 1-800-225-6074.

25

REPLACEMENT PARTS SPECIFICATIONS

Remote Control 136-4926

Wireless Controller

136-5007

LCD Backlighting LED

Resolution 800 (RGB) x 480

Pixels 1,152,000

Operation Temperature 32 ~131º F (0 ~ 50º C)

Storage Temperature -4 ~ 158º F (-20 ~ 70º C)

Backlit life 10,000 Hours

Video Display System NTSC / PAL

Headphone Audio Output 0.03W @ 32 ohms

Video Output 1.0Vp-p @ 75 ohms

Power Source 12V DC

Dimension L xWxH

12" x 12" x 2.5"

315mm x 315mm x 64.5mm

Specifications subject to change without notice.

26

AUDIOVOX LIMITED WARRANTY

Applies to Audiovox Mobile Video Products

AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that, should this product or any part
thereof (except game controllers), under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of
original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair
labor. A game controller, if supplied, is similarly warranted for (90) days.

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred for
installation, removal or reinstallation of the product, or to damage to digital memory/media devices, gaming devices, discs, speakers, accessories, or
vehicle electrical systems.

This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE
EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND,
IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITH IN A PERIOD NOT
EXCEEDING 12 MONTHS AFTER EXPIRATION OF THE WARRANTY. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is authorized
to assume for the Company any liability other than expressed herein in connection with the sale of this product.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the
above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from
state to state.

Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 1-800-645-4994

l

128-5148F

27

128-8667A© 20 0 AUDIOVOX,150 Marcus Blvd. Hauppauge, NY 117881