Audiovox VOD108 Installation Manual

VOD108

10.2” OVERHEAD LCD MONITOR

WITH DVD PLAYER

ON OFF AUTO

Installation Guide

Important Notice

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in "park" or when the vehicle s parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.

Installation of overhead products requires careful planning and preparation. Be

extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants. If you have any questions regarding wire routing in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product.

Important Note

The VOD108 incorporates three new features:

1) A wireless FM Modulator

2) Snap on Covers with matching Trim Rings (Shale and Pewter).

Select the color that matches the interior trim.

Please be advised that the wireless FM modulator will perform well in most applications. However, in certain applications the quality of the wireless signal may be less than optimal, resulting in static or strong local station bleed thru. If this is the case, an optional relay box is available. The Audiovox part number is SIRSWB and it plugs into the 1/8" jack located next to the FM antenna on the side of the chassis. This relay box is installed between the vehicle antenna and the car radio to provide the best possible FM reception of the DVD player audio. When the SIRSWB is installed it is recommended that the wireless FM antenna that is plugged into the printed circuit board next to the 3.5mm jack be unplugged.

Licensed under one or more of the following patents, Patent NOS. 5,775,762 , 5,927,784 and 6,678,892

MATERIALS INCLUDED IN THIS PACKAGE:

1) 10.2” TFT LCD Overhead Monitor With DVD Player - (1pc)

2) 12 Pin Power / Signal Harness (P/N 112-3483) - (1pc)

3) 2 Pin Power Wire Harness With Choke (P/N 112B3143) - (1pc)

4) AUX Pigtail (P/N 112B3227) - (1pc)

5) 12 Pin AV Adapter Cable (P/N 112-4094) - (1pc)

6) Hardware Package Screws ISO M3 x 8mm Long - (5pcs) #4 x 5/16" Self Tapping Screws - (1pc) #4 x 7/16" Self Tapping Screws - (3pcs) #8 x 3/8" Self Drilling Screws - (4pcs) M5 Screws - (4pcs)

7) Remote Control (P/N 136-4840) - (1pc)

8) Universal Mounting Bracket (P/N 108-3921) - (1pc)

9) Pry Tool - (1pc)

10) USB Cover - (1pc)

11) Screw Cap - Shale - (2pcs)

- Pewter - (2pcs)

12) Trim Ring - Shale (P/N 102-4231) - (1pc)

- Pewter (P/N 102-4232) - (1pc)

13) Snap On Cover (Screen Back) - Shale (P/N 102-4233) - (1pc)

- Pewter (P/N 102-4234) - (1pc)

14) Snap On Cover (Shroud) - Shale (P/N 102-4596) - (1pc)

- Pewter (P/N 102-4597) - (1pc)

15) Wireless Headphones (P/N IR1CFF) - (2pcs)

16) Wireless Game Controller (P/N 136-4197) - (1pc)

Optional Accessories

17) SIRSWB Relay Box (P/N 112C3159) - (1pc)

ON OFF AUTO

MUTE

AUDIO

ZOOM

REPEAT

SUBTITLE

VOLUME

DVDTV

SETUP

DISC MENU

M1 M2

PIX

ENTER

DVD SOURCE

POWER

DISPLAY

SOURCE

DVD SOURCE

SYSTEM MENU

IRT ON/OFF

FMM ON/OFF

(Optional)

TOOLS RE QUIRED:

#2 Phillips Screwdri ver #1 Phillips Screwdri ver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and cont inuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark tr im ring if used) Misc. electrical connectors (to connect to vehicle power source). Re quiremen ts will vary from vehicle to vehicle) DVD Movie (to veri fy system operation after installation)

Installing The Snap On Covers

1. 5.

ON OFF AUTO

3.2. 4.

Housing

Snap On Cover

(Shroud)

1 Pewter, 1 Shale

Snap On Cover

(Screen Back Cab)

1 Pewter, 1 Shale

Pry Tool

Screw Cap

(L & R)

2 Pewter, 2 Shale

USB Cover

Place the pod on a soft surface to avoid damaging the plastic.

Installing The Shroud

catch catch

Remove

tape backing

before installing.

(A)

Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place.

Installing The Screen Cover

(B)

ON OFF AUTO

Open the screen and hook the two tabs “B” on the bottom edge of the screen. Snap the opposite side over the hinge.

Installing The Screw Cap & USB Cover

Plug -in

ON OFF AUTO

Screw cap & USB cover get installed after the unit is mounted.

ON OFF AUTO

Plug -in

+ 8 hidden pages