Audiovox VOD1022 User Manual

ELECTRONICS CORP .

VOD705

VOD1022

DVD PLA YER

WITH

DROP-DOWN

VIDEO

TV/MONITOR

Release Date 6/28/04

128-7094

1 of 31

Important Notice

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play , the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly , to the operator of the motor vehicle. It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a screen that is located in the motor vehicle at any point forward of the back of the driver’s seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety , the VOD1022 should never be installed where it will be visible, directly or indirectly , by the operator of the motor vehicle.

Warnings

Do not use any solvents or cleaning materials when cleaning the video monitor. Use only a lightly dampened lint free cloth to wipe the screen if it is dirty . Lock the LCD screen in the fully closed position when not in use.

Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome lights, if left on, can drain the vehicle’s battery .

Television Reception

This entertainment system is designed primarily for viewing prerecorded movies or playing video games. T elevision reception in a moving vehicle will be limited and in some areas will not be possible due to weak and variable signal strength. T elevision viewing in a stationary vehicle will result in an improvement, but may still be marginal due to signal strength. The quality of the picture will not be consistent with home TV reception. Reception may be affected by weather and distance from TV st ation. A weak signal may cause the picture to roll, be snowy , or cause some color loss.

Licensed under one or more of the following patents, Patent NOS. 5,775,762 and 5,927,784

-2-

128-7094

2 of 31

Congratulations on your purchase of the Audiovox VOD1022 DVD Player with Drop-Down Video monitor/ TV. The VOD1022 has been designed to give you and your family many years of video entertainment in the mobile environment. Please read the directions that follow to familiarize yourself with the product and to ensure that you obtain the best results from your equipment. Please note: Installation options vary, see the individual owner’s manuals for each component in your system to obtain a full understanding of each component’s operation.

Safety Precaution

For safety reasons, when changing video media it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. System adjustments can be accomplished using the remote control unit, while seat-belts remain fastened. Enjoy your Audiovox entertainment system but remember-safety of all passengers remains the number one priority.

Features

••

• 10.2” TFT Active Matrix Color LCD Monitor

••

• Built-In DVD Player

••

• DVD/CD/MP3 compatible

••

• On Screen Display

••

• 16:9 and 4:3 Screen Mode (switchable)

••

• IR Remote Repeater for AV1 Inputs

••

• Dual IR Sensors

••

• Remote Control

••

• Four Source Selection (DVD/TV/A V1/AUX)

••

• AUX Input for Game or Camcorder

••

• 6 Frequency FM Modulator

••

(Remote Control Accessible)

••

• Dual Headphone Jacks

••

• Built-In TV Tuner

••

• Built-In Dual IR Transmitter

••

• Built-In Dome Lights with Switch

••

• Last position memory for DVD

••

-3-

128-7094

3 of 31

Controls and Indicators Diagram

10 11

12 13

2 3

4 5

21 20

19 18

17 16

-4-

128-7094

4 of 31

Main Function Descriptions

1. DVD Disc insertion slot – For loading Disc.

2. POWER Button – Bright red when system is on dim when

off.

3. EJECT ( ) Button – For ejecting discs from the disc compartment.

4. PLAY ( ) Button – This button is used to enter the play mode.

5. STOP ( ) Button – To stop playback.

6. Infrared Transmitter and Sensor – Use to transmit audio

to wireless headphones. Also allows the remote control to operate the VOD1022 and to control other accessories in the system.

7. VOD1022 Ventilation Opening.

8. Dome Lights – Provide additional interior illumination.

9. SOURCE Select – Used to select one of the four sources

(TV ,AV1, AUX, DVD).

10. CHANNEL ( ) Button – Use this button to decrease the channel number to the desired number. Note : When TV

function is selected.

11. AUTO PROGRAM Button – Allows the user to scan and store active TV stations into memory.

12. CHANNEL( )Button – Use this button to increase the channel number to the desired number. Note : When TV

function is selected.

13. Side Remote Sensor Eye – Allows the remote control to operate the VOD1022, control volume to wired headphone jacks and control the other accessories.

14. AUX Input (Use with supplied A/V adapter)

••

• Auxiliary Audio Right Input.

••

• Auxiliary Audio Left Input.

••

• Auxiliary Video Input.

••

15. Drop Down LCD Panel.

16. Headphone Jack – Allow the use of wired headphones

with a 1/8” plug for listening to video program audio.

17. Screen release – Moves in direction of the arrow to release the drop down screen.

18. VOLUME ( ) Button – Use this button to decrease the volume level of the wired headphone jacks. It is also used to make picture adjustments in the picture select mode.

-5-

128-7094

5 of 31

19. FM Select Button – Each time this button is pressed the FM Modulator will cycle through the following options: (FM OFF – POD AUDIO – SAT AUDIO) The frequency of the FM modulator will remain same.

20. VOLUME ( ) Button – Use this button to raise the volume level of the wired headphone jacks. It is also used to make picture adjustments in the picture select mode. Note :

Audiovox recommends the use of the Audiovox HP275 Headphones when using wired headphones.

21. Three position Dome Light Switch

• Auto – Automatically switches on the dome lights in

conjunction with the vehicle’s interior illumination.

• Off – The dome lights will not turn on in this position.

• On – Turns on the dome lights.

Note:The volume buttons will not effect the volume of the wireless

headphones or the wired FM modulator. When using these devices the volume must be adjusted with the wireless headphone volume control or with your radio’s volume control (see page 15, Wireless Headphones, or page 16, Wired FM Modulator).

-6-

128-7094

6 of 31

Remote Control Operation

Battery Installation

Before attempting to operate your Remote Control, install the batteries as described below.

1) Turn the Remote Control face down. Using a fingernail, lift the battery cover off.

2) Install two “AAA” batteries as shown. Make sure that proper polarity (+ or -) is observed.

3) Align the cover tabs with the remote control and press down until the cover clicks.

The remote control will operate the VOD1022 and most Audiovox VCP’s. It is not a universal remote control and will not control equipment from other manufacturers.

6 7

8 9

13 14 15

POWER

SOURCE

AUTO

MEMORY

SKIP/

ERASE/

WRITE

MUTE

RETURN

–+

Enter

VOL

REPEAT

EJECT

PIX

SETUP

30 29

26 25 24

21 22

20 19

18 17

-7-

128-7094

7 of 31

Remote Control Function Descriptions

*Function control is available on the unit and the remote control.

1. POWER Button*

Press this button to turn the VOD1022 on. Press the button again to turn the VOD1022 off.

2. SOURCE Button*

Video signals from video equipment connected to the audio / video inputs can be displayed on the monitor by pressing this button. Each time the button is pressed, the audio / video source will change sources in the following order: DVD, A V1, A V2 and AUX.

3. AUTO MEMORY Button (AUTO PROGRAM Button)*

When the AUTO MEMORY button is pressed, all channels are searched and channels that are detected with signals of sufficent levels are automatically stored.

4. SKIP/SEARCH Button

This button selects betweeen SKIP and SEARCH mode. In “SKIP mode” the TV tuner will tune and stop on channels that are programmed into memory when the CHANNEL UP/DOWN buttons are used. When in the SEARCH mode, the TV will stop on all active channels.

5. ERASE/WRITE Button

While tuned to a channel, pressing this button will either store or erase the channel from memory. The stored channel numbers are displayed in “GREEN” on the LCD display screen, and the erased channel numbers are displayed in “RED”.

-8-

128-7094

8 of 31

6. Channel Up ( ) Button*

Use this button to increase the channel number to the desired channel and to scroll upward in menu options.

7. MUTE Button

Press this button to mute the audio. Pressing the button again restores the sound to the previously set level.

8. ENTER Button

Used to confirm a selected setting or option.

9. LEFT ( ) Button

Allows the user to shift left in the menu options.

10. MENU Button

Allows the user to access the DVD (DVD MODE) main menu and monitor menu (TV MODE).

11. RETURN Button

Allows the user to return to the menu while PBC on.

Note: This function only present on VCD2.0.

12. TV Mode Select Button

Switches certain function keys on the remote control for TV functions.

-9-

128-7094

9 of 31

+ 21 hidden pages