Audiovox VOD10 User Manual

VOD10

10.2” OVERHEAD LCD MONITOR

WITH DVD PLAYER

Installation Guide

Important Notice

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in "park" or when the vehicle s parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.

Installation of overhead products requires careful planning and preparation. Be

extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants. If you have any questions regarding wire routing in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product.

Important Note

The VOD10 incorporates two new features:

1) A wireless FM Modulator

2) Snap on Covers with matching Trim Rings (Shale and Pewter).

Select the color that matches the interior trim.

Please be advised that the wireless FM modulator will perform well in most applications. However, in certain applications the quality of the wireless signal may be less than optimal, resulting in static or strong local station bleed thru.

Licensed under one or more of the following patents, Patent NOS. 5,775,762 and 5,927,784

MATERIALS INCLUDED IN THIS PACKAGE:

1) 10.2” TFT LCD Overhead Monitor With DVD Player - (1pc)

2) Hardware Package Screws ISO M3 x 8mm Long - (5pcs) #4 x 5/16" Self Drilling Screws - (1pc) #4 x 7/16" Self Drilling Screws - (3pcs) #8 x 3/8" Self Drilling Screws - (4pcs) M5 Screws - (4pcs)

3) Remote Control (P/N 136-4840) - (1pc)

4) Universal Mounting Bracket (P/N 108-3921) - (1pc)

5) Pry Tool - (1pc)

6) Screw Cap - Shale - (2pcs)

- Pewter - (2pcs)

7) Trim Ring - Shale (P/N 102-4231) - (1pc)

- Pewter (P/N 102-4232) - (1pc)

8) Snap On Cover (Screen Back) - Shale (P/N 102-4233) - (1pc)

- Pewter (P/N 102-4234) - (1pc)

9) Snap On Cover (Shroud) - Shale (P/N 102-4235) - (1pc)

- Pewter (P/N 102-4236) - (1pc)

10) Wireless Headphones - (2pcs)

POWER EJECT

M1 M2

SOURCE

MUTE

TV DVD

DVD SOURCE VOLUME

PIX

SYSTEM MENU DISC MENU ZOOM

REPEAT

ENTER

SUBTITLE SETUPDISPLAY

AUDIO

1 2 3 4

5 6 7 8

IRT

FMM

9 0

ON/OFF

TOOLS RE QUIRED:

#2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Ra zor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as nece ssary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continui ty: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to ma rk trim ring if used) Misc. electrical connectors (to co nnect to vehi cle po wer source). Requirem ents will vary from vehicle to

vehicle)

DVD Movie (to verify system oper ation after installation)

Installing The Snap On Covers

1. 5.

3.2. 4.

Housing

Place the pod on a soft surface to avoid damaging the plastic.

Snap On Cover

(Shroud)

1 Pewter, 1 Shale

Snap On Cover

(Screen Back Cab)

1 Pewter, 1 Shale

Pry Tool

Screw Cap

(L & R)

2 Pewter, 2 Shale

Installing The Shroud

catch catch

Remove

tape backing

before installing.

(A)

Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place.

Installing The Screen Cover

(B)

Open the screen and hook the two tabs “B” on the bottom edge of the screen. Snap the opposite side over the hinge.

Installing The Screw Cap

Plug -i n

Screw cap get installed after the unit is mounted.

+ 8 hidden pages