Audiovox VM9410 Owners Manual
VM9410
Owner’s Manual
VM9410
LO/DX
OPEN
DVD-R
7-INCH TFT
PWR
VM9410
2-6CH
SRC
AV AUX I N
Push
ENTER
CONTENTS
Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s
manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to
use all the features of your new Jensen VM9410 Mobile Multimedia AM/FM/DVD Receiver for
maximum enjoyment.
Preparation............................................................................................. 1
Features........................................................................................................................ 1
Tools and Supplies........................................................................................................ 1
Disconnecting the Battery.......................... ................................................................... 1
Installation.............................................................................................. 2
Pre-installation .............................................................................................................. 2
Wiring............................................................................................................................ 2
Final Installation............................................................................................................ 2
Final ISO-DIN Installation.............................................................................................. 2
Controls and Indicators......................................................................... 4
Button Operation........................................................................................................... 4
Controls and Indicators......................................................................... 5
Controls and Indicators......................................................................... 6
LCD Display/Indicators.................................................................................................. 6
FRONT ZONE Remote Control.............................................................. 7
Rear Zone Remote COntrol................................................................... 9
Using the TFT Monitor......................................................................... 10
Open/Close TFT Monitor............................................................................................. 10
TFT Monitor Auto Open .............................................................................................. 10
Reverse Driving Use................................................................................................... 10
Monitor Tilt Angle Adjustment..................................................................................... 10
Aspect Ratio................................................................................................................ 10
Image Setting.............................................................................................................. 10
Parking Brake Inhibit................................................................................................... 10
Monitor Movement Mechanism................................................................................... 10
operating instructions......................................................................... 11
Power On / Off ............................................................................................................ 11
Audible Beep Confirmation ......................................................................................... 11
Mute............................................................................................................................ 11
Playing Source Selection............................................................................................ 11
Volume Adjustment..................................................................................................... 11
Audio Control Menu .................................................................................................... 11
Six-Channel Audio Control.......................................................................................... 11
Rear Zone................................................................................................................... 11
System Reset.............................................................................................................. 11
Line Mute .................................................................................................................... 11
System Setup Menu....................... ... .... ... ... ... .... ... ............................... 12
General Setup Menu................................................................................................... 12
ASP (Audio Sound Processing) Config Menu............................................................. 12
Exiting the System Setup Menu.................................................................................. 13
Tuner Operation................................................................................... 14
Tuner TFT Display ..................................................................................................... 14
Tuner LCD Display..................................................................................................... 14
Switch to Radio Tuner source.................................................................................... 14
Select FM/AM Band................................................................................................... 14
Auto Tuning................................................................................................................ 14
Seek Tuning............................................................................................................... 14
Manual Tuning ........................................................................................................... 14
Using Preset Stations................................................................................................. 14
Auto Store (AS).......................................................................................................... 14
Local Radio Station Seeking (LOC) ........................................................................... 14
DVD Player Operation ......................................................................... 15
Opening/Closing the TFT Video Screen .................................................................... 15
DVD LCD Display....................................................................................................... 15
Insert/Eject Disc......................................................................................................... 15
Ejecting a Disc ........................................................................................................... 15
Reset the Loading Mechanism................................................................................... 15
Controlling Playback .................................................................................................. 15
Accessing the DVD Menu.......................................................................................... 15
Moving Through Chapters............................................................................. ............. 15
Fast Forward/Fast Reverse........................................................................................ 15
Scanning.................................................................................................................... 15
Alternating Between 2-Channel and 6-Channel Mode............................................... 15
Goto Search............................................................................................................... 16
Direct Chapter / Track Selection ................................................................................ 16
Viewing an Alternate Picture Angle (DVD Only) ........................................................ 16
Zooming..................................................................................................................... 16
Multi-Language Discs (DVD Only)............................................................................. 16
PBC (Play back Control) (VCD Only)......................................................................... 16
Playback Information.................................................................................................. 16
General Disc Information ........................................................................................... 17
DVD Setup Menu.................................................................................. 18
Accessing the DVD Setup Screen ............................................................................. 18
LANGUAGE Menu..................................................................................................... 18
VIDEO Menu.............................................................................................................. 18
AUDIO Menu.............................................................................................................. 18
SPK (Speaker) CONFIG Menu.................................................................................. 19
RATING (Parental Lock) Menu .................................................................................. 19
CD Player/Changer Operation ............................................................ 20
MP3/WMA Operation................................................................................................. 20
CD Changer Operation .............................................................................................. 20
Troubleshooting .................................................................................. 21
Error Messages.......................................................................................................... 22
Care and Maintenance............................................................................................... 22
Specifications ...................................................................................... 23
CEA Power Ratings ................................................................................................... 23
ii
VM9410
PREPARATION
Congratulations on your purchase of the Jensen VM9410
Mobile Multimedia AM/FM/DVD Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen VM9410
installed by a reputable installation shop.
Features
1. 1 DIN Size.
2. Ultra slim slot-in DVD core mechanism.
3. 7 inch Panasonic TFT monitor.
4. Built-in 4X40W power amplifier audio output.
5. Multi-zone independent playing with a maximum of 3zone independent playing (eg.Front Zone: radio as the
background; Rear Zone: playback DVD).
6. Supports optional external CD changer.
• Select previous/next disc.
• Playback previous/next chapter.
• Direct track/chapter selection.
• Single track/chapter and disc replay.
• Random playback/scan.
7. AM/FM tuner.
• Auto/Manual search for radio station and pre-set
station memory.
• 30 pre-set radio stations (12 AM/18 FM).
• Distant/Local radio station seeking.
8. Multiple video System with Auto/Manual PAL and NTSC
video system selection.
9. Dual LCD Display.
10. Wide screen TFT display and segment LCD display.
11. FULL, WIDE, and NORMAL screen modes.
12. TFT automatic mechanism – Simply press a button to
adjust the TFT monitor display angle in full range or step
by step. Last position memory recalls your favorite
viewing position.
13. Auto-activated rear view video camera – Reverse
driving automatically activates the TFT monitor and the
rear view video camera; the Image captured from the
camera is displayed.
14. TFT monitor mechanism overload protection – If the
TFT monitor becomes overloaded by a blocked or
unclear moving path, its motion is ceased automatically
to protect the mechanism.
15. Fully compatible with CDDA, VCD, SVCD, CD-R, CDRW and DVD.
16. Multi-language, multi-subtitle, and multi-angle playback
options.
17. Last Playback Memory – When powering on the unit,
every setting and playing status remains the same as
when the unit was powered off.
18. Parental lock – Uses a password and disc-rating setup
to prevent unauthorized user access to irrelevant
display content.
19. Mute function – Automatically lower/mute the volume
when a dedicated external device such as GPS system
or car phone is active.
20. Joystick (5-way) control – The joystick provides easy
navigational control via a 4-directional control with a
clickable center control.
21. Rotary volume control.
22. Two independent full function IR remote controls – one
for the front zone, the other for the rear zone, without
interference.
23. Voltage overload and underloaded protection – The
operating voltage of this unit is between 10.5V and 16V.
Any supplied voltage out of this range causes the unit to
power off automatically to ensure normal operation in
any circumstance.
24. Mechanical anti-vibration system + electronic shock
protection – mechanical anti- vibration system
accompanied by a 16Mbit electronic shock protection
promotes the smoothest disc playback possible, even
under the toughest road conditions.
Tools and Supplies
You will need these tools and supplies to install your
VM9410:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident (except
when using for rear view video camera) never use the
video display function while driving the vehicle. This is a
violation of federal law.
WARNING! Never disassemble or adjust the unit without
the assistance of a professional. For details, please
consult your local car stereo specialty shop.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Do not change the fuse on the power cord
without professional guidance. Using an improper fuse
may cause damage to the unit and result in a fire.
WARNING! To prevent damage to the screen, avoid
touching it with your fingers or other objects.
WARNING! The monitor employs an automatic motorized
mechanism. To prevent damage to the core mechanism,
please do not push, pull or swivel the monitor manually.
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and
remove the negative (-) battery cable prior to installation.
NOTE: If the VM9410 is to be installed in a car equipped
with an on-board drive or navigation computer, do not
disconnect the battery cable. If the cable is
disconnected, the computer memory may be lost. Under
these conditions, use extra caution during installation to
avoid causing a short circuit.
1
INSTALLATION
7-INCH
TFT
7-INCH
TFT
7-INCH
TFT
Pre-installation
1. Press the metal levers on both sides to remove the halfsleeve from the radio.
2. Remove the transport screws.
PREPARE RADIO
1
7-INCH
D
IGITAL
7-INCH
T
FT
BAND
T
FT
AS/PS
VM9510
AM/FM/DVD/MP3
Push
MUTE
3. Install the half-sleeve.
a. Install adapter if necessary (optional).
b. Install half-sleeve into adapter or dashboard (only
c. Locate the series of bend tabs along the top,
d. Install support strap to make the unit more stable.
INSTALL HALF SLEEVE
R
ECEIVER
PWR
OPEN
DISP
AVAUXIN
Push
MODE
ENTER
2
use the supplied screws). Do not force the sleeve
into the opening or cause it to bend or bow.
bottom and sides of the mounting sleeve. With the
sleeve fully inserted into the dashboard opening,
bend as many of the tabs outward as necessary so
that the sleeve is firmly secured to the dashboard.
3d
3c
CAUTION! Be careful not to damage the car wiring.
4. Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve.
Wiring
Complete wiring as illustrated in the wiring diagram on page
3. Once the wiring is complete, reconnect the battery
negative terminal. If there is no ACC available, connect the
ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct
type and amperage to avoid damaging the radio. The
VM9410 uses one 10 amp mini-ATM fuse, located in the
black filter box in-line with the main wire harness.
Final Installation
After completing the wiring connections, turn the unit on to
confirm operation (ignition switch must be on). If unit does not
operate, recheck all wiring until problem is corrected. Once
proper operation is achieved, turn off the ignition switch and
proceed with final mounting of the chassis.
1. Connect wiring adapter to existing wiring harness.
2. Connect antenna lead.
3. Carefully slide the radio into the half-sleeve making sure
it is right-side-up until it is fully seated and the spring
clips lock it into place.
NOTE: For proper operation of the CD/DVD player, the
chassis must be mounted within 20° of horizontal. Make
sure the unit is mounted within this limitation.
4. Attach one end of the perforated support strap
(supplied) to the screw stud on the rear of the chassis
using the hex nut provided. Fasten the other end of the
perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut
provided. Bend the strap to position it as necessary.
VM9410
5. Replace any items you removed from the dashboard.
FINAL INSTALLATION
5
1
7-INCH
D
IGITAL
7-INCH
T
FT
BAND
T
FT
AS/PS
VM9510
AM/FM/DVD/MP3
Push
R
ECEIVER
MUTE
PWR
OPEN
DISP
AVAUXIN
Push
MODE
ENTER
3
Final ISO-DIN Installation
1. Remove trim ring.
2. Mount factory brackets on new radio using existing
screws from old radio.
3. Slide radio chassis into dash opening and secure.
4. Reinstall dash panel.
FINAL ISO-DIN INSTALLATION
3
7-INCH
DIGITALTFT
7-INCHTFT
BAND
AS/PS
VM9510
AM/FM/DVD/MP3
Push
RECEIVER
MUTE
PWR
OPEN
DISP
AVAU
X
IN
Push
MODE
ENTER
1
4
4
2
2
CAUTION! The rear of the radio must be supported with
the strap to prevent damage to the dashboard from the
3a
weight of the radio or improper operation due to
vibration.
3b
2
VM9410
Car
WIRING DIAGRAM
External Power Amplifier
Antenna Jack
Antenna
Car Phone
FRONT L+
FRONT L-
FRONT R+
FRONT R-
REAR R+
REAR R-
REAR L+
REAR L-
GREY
BLUE
RED
WHITE
RED
WHITE
Auto antenna contr ol(co nnect t o antenna
control lead & power supply of ante nna
amplifier)
External power ampl if ier c ontrol
Mute(leave open if not connect ed)
FRONT L
FRONT R
REAR R
REAR L
CENTER
SUB.W
SURROUND
REAR R
SURROUND
REAR L
FRONT R
FRONT L
BLUE
ANT.CONT
BLUE/WHITE
P.CONT
BROWN
MUTE
WHITE +
WHITE/BLACK -
GREY +
GREY/BLACK -
PURPLE +
PURPLE/B LA CK -
GREEN +
GREEN/BLACK -
CD Changer IP-BUS Cable / BLACK
HEADPHONE L
HEADPHONE R
AUX IN/L
AUX IN/R
PINK
PRK SW
GREEN/WHITE
REVERSE +
RED
ACC
YELLOW
BATT
BLACK
GND
FUSE(10A)
ACC
BATTERY +
BATTERY
CD Changer
WHITE
RED
WHITE
RED
Parking Brake Lig ht
compatible wi th SANYO di sc chang ers
Wireless H eadphone
Additional Rear
Zone Video
Rear Zone
Video 1
External AV System
Parking Brake Swit ch
Ground
Rear View Video Camera
YELLOW
YELLOW
AUX IN VIDEO
YELLOW
REAR VIDEO
OUT 1
YELLOW
REAR VIDEO
OUT 2
Reverse Driving Li ght Gearbox Switch
Ground
Ignition Switch
Battery
Ground
3
CONTROLS AND INDICATORS
Button Operation
1. OPEN
Press the OPEN button (1) to activate the automatic
mechanical system and move the TFT monitor into viewing
position.
2. WIDE/PICTURE
Press the WIDE/PICTURE button (2) to adjust the display
aspect of the picture to one of three settings: Wide, Full or
Normal.
3. ( )
Press the button (3) to adjust the upward tilt angle of the
screen one step at a time. Press and hold this button to
continuously adjust the upward tilt.
4. ( )
Press the button (4) to adjust the downward tilt angle of the
screen one step at a time. Press and hold this button to
continuously adjust the downward tilt.
5. DSP
Press the DSP button (5) to display system information on
the screen. Press and hold this button to enter/exit System
Function set-up.
6. SEL/LOC/DX
Rotate the SEL/LOC/DX knob (6) to adjust the volume. Press
and release to enter and/or confirm audio settings. Press and
hold to activate the Local (LOC) setting.
7. POWER/MUTE
Press the POWER/MUTE button (7) once to turn the unit on.
Press again to mute the volume. Press and hold to turn the
unit off.
8. 1/DISC-
DVD Mode: Press to select audio language during playback.
TUNER Mode: Press once to play preset radio station
channel 1. Press and hold to store the current radio station in
preset channel 1.
CDC Mode: Press to play the previous disc.
9. 2/DISC+
DVD Mode: Press once to select the subtitle language during
playback.
TUNER Mode: Press once to play preset radio station
channel 2. Press and hold to store the current radio station in
preset channel 2.
CDC Mode: Press to play the next disc.
6
VM9410
LO/DX
OPEN
7-INCH TFT
DVD-R
PWR
7 8 9
2326
VM9410
1010 11 12
2-6CH
SRC
131415 16 19
5
25
1
AV AUX I N
VM9410
Push
ENTER
24
4
3
2
21
18
17
20
22
4
VM9410
7-INCH TFT
CONTROLS AND INDICATORS
10. 3/SCN
DVD Mode: Press once to start scan playback.
TUNER Mode: Press once to play preset radio station
channel 3. Press and hold to store the current radio station in
preset channel 3.
11. 4/REP
DVD Mode: Press once to start repeat playback.
TUNER Mode: Press once to play preset radio station
channel 4. Press and hold to store the current radio station in
preset channel 4.
12. 5/2-6CH/RDM
DVD Mode: Press once for random playback.
TUNER Mode: Press once to play preset radio station
channel 5. Press and hold to store the current radio station in
preset channel 5.
CD Mode: Press and hold to switch between 2 channel & 6
channel audio output.
13. 6/STOP
DVD Mode: Press once to stop playback.
TUNER Mode: Press once to play preset radio station
channel 6. Press and hold to store the current radio station in
preset channel 6.
14. AF/BAND/PAUSE
DVD Mode: Press to pause playback.
TUNER Mode: Press to switch between FM and AM.
15. SRC/P.MODE
Press once to select playing mode.
Press and hold to toggle rear zone mode On/0ff.
16. ( )
DVD Mode: Press once to play back previous chapter/track.
TUNER Mode: Press once to auto search for the previous
available radio station. Press and hold to decrease the tuning
frequency step by step.
MENU Mode: Press once to move the cursor to the left.
17. ( )
DVD Mode: Press once to enter the next chapter or track.
TUNER Mode: Press once to auto-search the next available
radio station. Press and hold to increase tuning frequency
step by step.
MENU Mode: Press once to move the cursor to the right.
6
18. ( )
DVD Mode: Press once for fast forward/fast reverse.
MENU Mode: Press once to move the cursor up.
19. ( )
DVD Mode: Press once for slow forward/slow reverse.
MENU Mode: Press once to move the cursor down.
20. PLAY/ENTER
DVD Mode: Press once to start a playback.
Press once to confirm a selection.
21. ( )
Press once for disc insertion/ejection.
Press and hold to reset core mechanism position.
22. RESET
Press to reset system settings to factory default (except the
password and parental lock setting).
23. LCD Display
24. TFT Display
25. IR Remote Control Receiver
26. AS (Auto Store/Preset Scan)
Press once to scan current radio station.
Press and hold to auto store strong radio stations in the six
preset channels.
7-INCH DIGITAL TFT
7-INCH TFT
BAND
VM9410
LO/DX
AS
PWR
7 8 9
AM/FM/DVD/MP3 RECEIVER
1010 11 12
DISP
2-6CH
SRC
13 15 16 19
1
514 2326
OPEN
21
Push
ENTER
18
17
20
25
22
5
CONTROLS AND INDICATORS
LCD Display/Indicators
1. Disc Indicator
Illuminated when disc is loaded
2. DVD Playback Indicators (SCN/RPT/RDM/ALL)
The following DVD playback indicators become Illuminated
when the corresponding function is active:
• SCN: scan playback
• RPT: repeat playback
• RDM: random playback
• ALL: playback all chapters
3. Loudness Indicator (LOUD)
The loudness indicator becomes illuminated when the LOUD
function is activated.
4. Main Display
The main display is an 8 digit, 14 segment LCD which
displays the time, tuning frequency and other text
information.
5. Channel/Disc Display
The channel/disc display is a 2 digit, 7 segment LCD display
which displays the disc number or radio channel indicators
when the corresponding function is active:
• CH: radio is activated
• DISC: DVD or CDC mode is activated
6. Stereo/Local Indicator
The stereo/local indicator illuminates one of the following
indicators when the corresponding function is active:
• ST: radio is in stereo mode
• LOC: local radio station seeking function is activated
VM9410
1 2 3 4 5 6
6
Loading...