Audiovox SCO2, SCO1, SKS1, SKL2 Owner's Manual

OWNER’S MANUAL

AND

INSTALLATION INSTRUCTIONS

FOR

SINGLE SEAT WARMER

SKS1, SKL2, SCO1, SCO2, SSP1

CONTENTS

Thank you for choosing a Audiovox product. We hope you will nd the instructions in this owner’s/installation manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new seat warmer for maximum enjoyment.

Cautions 2 Kit Features 3 Installation Preparation 3 Seat Cushion 4 Back Rest 9 Seat Heater Switch 9 Seat Heater Wire Harness 10 Final Seat Assembly 10 System Operation 11 Seat Heater Use 11 Troubleshooting 12 Wiring Diagram 13 Seat Heater Specications 14 Warranty 15

CAUTION

• Do not place any heavy, sharp or pointed objects on the seats.

• Any uid spilled on the seats may destroy the seat heater and may cause damage to the vehicle. Never operate the seat heater while the seats are wet or soaked with uid.

• Do not keep insulating material (sheets, covers, coats) on the seats while the seat heater is running. Do not place heat sensitive objects on the seats while the seat heater is running.

• To protect damage and discharge of the battery, avoid seat heater operation for extensive time periods without a running engine.

• Individuals, extra sensitive to heat, should only operate the seat heater in the “LO” position.

KIT FEATURES

Two Carbon Fiber Heater Pads Wire Harness with In-Line Fuse Round Switch with LED Indicator 8 Large Wire Ties

INSTALLATION PREPARATION

1. Seat heater system will NOT work on seats manufactured using the “foam in

place” (trim cover glued to foam pad) method of trim cover attachment.

2. If the vehicle is equipped with an anti-theft radio, the radio code must be

written down prior to disconnecting battery cable. The code must be reentered when the negative battery cable is re-installed.

3. If vehicle is equipped with an air bag, it is advisable to disconnect negative

battery cable for 3 minutes prior to beginning installation.

4. Only use parts and components supplied in kit for the seat heater installation.

The supplied components are carefully selected for optimal performance. Foreign parts may lead to problems which could result in potential damage to the seat heater components or vehicle.

NOTE: The installation of the heating pads must be free of creases and wrinkles.

6. Seats in vehicles with pre-loaded (power charge equipped) safety belts

must be removed and re-installed under strict adherence to the vehicle manufacturers instructions.

7. In cases where a seat is equipped with an occupant pressure sensor for air

bag deployment; please refer to the manufacturer’s manual for any specic instruction with regard to installing seat heater kits.

8. After installing seat heater wire harness, care must be taken to ensure all seat

motions are still possible without obstruction and the moving of the seat does not cause any interference that could damage the seat heater wire harness.

9. Installation of a seat heater system with seats containing seam lines running

front to rear (length wise) is not permitted. Only exception is if the heating pads are not directly located over the groove/s.

10. The overall side to side (width) of the heating pads must not be altered

CAUTION: Do NOT cut the side of the heating pad.

11. Both heating pads must be connected to ensure system functions properly.

The SCO1, SCO2 and SSP1 are premium, pre-cut pads that are designed to allow for quick installation on seats with vertical or horizontal listings.

No cutting or taping required by the installer.

WARNING: Metal, electrical conductors or hog rings are not to be placed on, through or across the heating element.

WARNING: Do not tap or solder seat heater harness to any airbag circuits. Yellow tape, tubing and connectors will indicate airbag circuits.

WARNING: Do not tap or solder seat heater harness to any pre-loaded safety belt circuits.

Installation Parts

Description Quantity

Seat Heater Pad 2

Wire Harness Assembly 1

Switch Assembly 1

Wire Ties 8

Seat Cushion

1. Prior to removing seat from vehicle, lay heating pads on seat to verify size and

t.

2. Park and secure the vehicle on a level surface.

3. Disconnect the negative battery cable. If you have any doubt concerning the

layout of the vehicle wire harness, consult the wiring diagram provided by the manufacturer.

4. Remove seat from vehicle and place on a suitable work table/area.

NOTE: Make certain to disconnect all wire connectors prior to removing seat from vehicle.

5. Disassemble seat as needed to gain access to seat cushion cover attachment

clips.

6. Unsnap j-clips and or remove “hog ring” clips and peel back cover. Refer to

Figures 1 and 2.

Figure 1

Figure 2

NOTE: If trim cover has hook and loop style tie down, care must be taken when removing cover.

+ 11 hidden pages