Audiovox CE148 User Manual
Portable Radio/CD Player
Operating Instruction
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
CAUTION
The use of optical instruments with this product will increase eye hazard.
INFORMATION (For the Customers in U.S.A)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet that is on a circuit different
from the one the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
For the Customers in the United Kingdom and/European
Countries
This Compact Disc player is
classified as a CLASS 1 LASER
product.
The CLASS LASER PRODUCT label
is located on the bottom exterior.
For the Customers in Canada
This apparatus complies with the Class B limits for radio noise emissions
set out in radio interference regulations.
This product contains
a low power laser
device.
EXPOSE THE UNIT TO RAIN OR MOISTURE.
TO AVOID ELECTRICAL SHOCK, DO NOT OPEN THE
CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
PRODUTO LASER CLASSE 1
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTER-
LOCKS DEFEATED.
AVOID EXPOSURE TO BEAM
at high volume while walking, especially at pedestrian crossings. You
should exercise extreme caution or discontinue use in potentially
hazardous situations.
Avoid using headphones/earphone at high volume. Hearing experts
advise against continuous, loud and extended play. If you experience a
ringing in your ears, reduce volume or discontinue use.
Keep the volume at a moderate level. This will allow you to hear outside
sounds and to be considerate to the people around you.
If you have any questions or problems concerning your unit, please
consult your nearest dealer.
IMPORTANT SAFETY INSTRUCTIONS
1. Read Instructions - All the safety and operating instructions should
be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be
followed.
5. Water and Moisture - The appliance should not be used near water
- for example, near a bathtub, washbowl, kitchen sink, laundry tub,
in a wet basement, or near a swimming pool, and the like.
6. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example,
the appliance should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or, placed in a
built-in installation, such as a book case or cabinet, that may impede
the flow of air through the ventilation openings.
7. Heat - The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
8. Power Sources - The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
9. Grounding or Polarization - Precautions should be taken so that
the grounding or polarization means of an appliance are not
defeated.
10. Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the appliance.
11. Cleaning - The appliance should be cleaned only as recommended
by the manufacturer.
FUNCTION OF CONTROLS
Opening the CD Door
to insert or remove a CD
Play/Pause
Press to begin play.
Press during play to pause.
To release pause, press pause.
(stop) /OFF (power off)
Disc playing stops, press again the unit will be
off.
Track search and fast forward/fast reverse
Press lightly/repeatedly:
To locate the beginning of the current selection or
previous selections.
Keep depressed:
To go back at high speed (search)
Press lightly/repeatedly:
To locate the beginning of next selection/
selections.
Keep depressed:
To go ahead at high speed (search)
PRESET/P. MODE
MEM/REPEAT/ENTER
BAND
OFF
TUNING
PRESET/PLAY MODE
Press the PRESET button in RADIO, after the
preset number appear, turn in a station using
preset.
P.MODE button for selecting the various play
mode.
MEMORY/REPEAT/ENTER
Press the MEM(MEMORY) button to storing
stations.
Enter button/Repeat button.
FUNCTION (CD/RADIO)
Set to CD or RADIO function.
BAND
Press the BAND button repeatedly to select
AM(MW) or FM to turn on radio.
OFF
Power off
TUNING (DOWN/UP)
Press the TUNING buttons turn into a station.
PRECAUTIONS
On safety
As the laser beam used in this compact disc player is harmful to
the eyes, do not attempt to disassemble the casing. Refer servicing to
qualified personnel only.
Do not put any foreign objects in the safety slot inside the disc
compartment. If you do so, the laser beam may come out when the lid is
opened.
Do not put any foreign objects in the DC IN 6V (external power input) jack.
Should any solid objects or liquid fall into the unit, disconnect the power
supply and have the unit checked by qualified personnel before operat-
ing it any further.
On operation
Since the CD system offers a wide dynamic range, the peaks of the high
level inputs are recorded with high fidelity, and the noise level is very
low. Do not turn up the volume while listening to a part of the disc with
no audio signals or very low level inputs. If you do, the speakers may be
damaged when the peak level of the sound is played. The lens on the
disc table should be kept clean. Do not touch the lens or poke at it. If you
do, the lens may be damaged and the unit will not operate properly.
On installation
Never install the unit where it would be subjected to:
- heat sources such as radiators or airducts
- direct sunlight
- excessive dust
- moisture or rain
- mechanical vibration or shock
- unleveled surface
12. Nonuse Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of
time.
13. Object and Liquid Entry - Care should be taken so that objects do
not fall, and liquids are not spilled, into the enclosure through
openings.
14. Damage Requiring Service - The appliance should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the
appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
15. Servicing - The user should not attempt to service the appliance
beyond that described in the operating instructions. All other servicing
should be referred to qualified service personnel.
PHONES jack
For connecting the headphones/earphone.
X-BASS
OFF: normal sound
ON: bass sounds are amplified
Mains socket (DC IN 6V)
Volume
Adjust the VOLUME.
ANTI-S HOCK
ON/OFF
M1~M5
ANTI-SHOCK
Press ANTI-SHOCK button to prevent sound
skipping.
+
M1, M2, M3, M4, M5, M5+
Preset number station buttons
POWER SOURCES
Using with batteries
Insert two size AA batteries (LR6 or UM-3 alkaline) according to the
" " and " " indications in the battery compartment.
Do not place any heavy object on top of the unit.
When the unit is used with an AC power adaptor, do not wrap the unit
in a cloth, blanket, etc. If you do, the temperature inside and outside
the unit may rise considerably, resulting in malfunctioning of the unit
or serious accidents.
If the unit is brought directly from a cold to a warm location, or is
placed in a very damp room, moisture may condense on the lens
inside the unit. Should this occur, the unit will not operate. In this case,
remove the disc and leave the unit in a warm place for several hours
until the moisture evaporates.
For the unit to operate at its best, it should not be subjected to
temperatures below 5°C (41°F) or above 35°C (95°F).
Notes on headphones/earphone
Do not use headphones/earphone while driving, cycling, or operating
any motorized vehicle, it may create a traffic hazard and is illegal in
some areas. It can also be potentially dangerous to play your headsets
Inserting batteries
Detach the battery cover on the
middle cabinet and insert two
size AA batteries (LR6 or UM-3
alkaline)
Notes on batteries
Insert batteries with correct polarity.
Do not use old batteries together with new ones or different types of
batteries together.
If the electrolyte inside the battery should leak, wipe the contaminated
parts in the battery compartment with a cloth and replace the old
batteries with new ones.
When the unit is not to be used for a long period of time, remove the
batteries.
Do not mix old and new batteries.
Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries.
POWER SOURCES
Notes on
During playback (batteries are in use), is on.
When the battery voltage level is low, will flash. 10~15 minutes,
playback still continues in this period.
Playback will automatically come to a stop when the batteries have no
more power. Do not repeat pressing as the unit may operate
incorrectly. Replace all the batteries with new ones.
will not be on if an AC adaptor is used.
Using on house current
If the unit you purchased does not include an AC power adaptor, please
use a 6V 450mA AC power adaptor. Otherwise use only the supplied
AC power adaptor.
Be sure to disconnect the AC power adaptor when the unit is not in use.
LISTENING TO THE RADIO
1. Set the FUNCTION switch to select "RADIO".
2. Press BAND button to select the desired band AM (MW) or FM.
3. Press TUNING buttons to turn the station.
To tune faster
Hold down the TUNING button. While the button is being held, the
frequency will change faster.
To search for a station quickly (AUTO Search)
Keep the TUNING's or button pressed until the tuner starts searching
for a station. After tuning in to a station, the search stops.
To stop the Auto Search manually, press the TUNING's or button.
* The Auto Search may not stop at stations with very weak signals.
To turn off the RADIO
Press OFF button or set the FUNCTION switch to "CD".
Presetting RADIO station
You can tune into a stored station directly by entering the preset number.
10 stations on FM band can be preset.
10 stations on AM (MW) band can be preset.
1. Set the FUNCTION switch to select "RADIO".
2. Press BAND button to select the desired band AM (MW) or FM.
3. Press TUNING buttons to tune your required station.
4. Press MEM (Memory) button.
The "PGM" indicator will flash in the display window.
5. Select a preset number (M1 ~M5+) button, or press the PRESET
button to select preset number.
6. Press MEM (Memory) button to store the station.
7. Repeat steps 2 to 6.
To select a numbered button from M6 to M10.
First press the M5+ button, then press one of numeric buttons.
Tuning into a preset station
Press the preset number (M1~M5+) button.
Or press the PRESET button to select preset number.
For better reception
To improve FM reception:
extend the headphone cord.
NOTE:
* The FM "STEREO" indicator lights up when the tuned-in station is
broadcasting in stereo and the reception is good.
DISC PLAYING
1. Set the FUNCTION switch to select " CD".
2. Open the CD door with the OPEN button.
3. Insert the CD with the printed side facing upwards and push the disc
gently until it clicks so that the disc fits into the pivot.
4. Press the CD door to close.
Note: To play an 8 cm (3-inch) disc, you can play it without an adaptor.
On display window
When you press , the display window shows:-
During play
The track number of the current selection appears.
When " /OFF" is pressed during play, total number of tracks on the disc
will be displayed and the unit is still on. If " /OFF" is pressed again the
unit will be returned to full stop mode. If " " is pressed the unit returns
to play mode. The unit will be returned to full stop mode automatically
after approximately 30 seconds if no button is pressed.
During pause
The playing track number flashes.
When no disc is inserted onto the player and when " " is pressed, the
To improve AM (MW) reception:
rotate the unit.
First track playing begins
Pause mode of the second track
display window shows " "
The unit cannot be operated when no disc message is displayed. After
approx. 30 seconds the unit will return to full stop mode, or reset the
player by pressing " /OFF" once and then insert a disc to start playing.
VARIOUS PLAYING MODES
During playback, every time the P. MODE (PLAY MODE) key is pressed,
the mode will change to the next one as follows:
NORMAL play -> INTRO -> PGM (PROGRAM) -> SHUFFLE
Normal Play - Playing the Whole Disc
The CD is played once from beginning to end.
INTRO Play - Playing the First Ten Seconds of All the Selections
1. Press P. MODE (Play mode) during play until
" " flashes in the display window.
2. Press to begin the INTRO play.
3. Pressing P.MODE again will cease the INTRO
play and continue playback in the NORMAL
play mode.
* INTRO play always starts from the first track.
PGM (Program) Play - Playing the Selections in the Desired Order
1. Press P. MODE (Play mode) button until
PGM flash and " " in the display
window.
2. Press or to select the desired
selection.
3. Press MEM/REPEAT/ENTER button to store
this track in memory.
4. To add additional tracks, repeat steps 2 and
3.
5. Press , "PGM" stops flashing and play
starts.
To Edit Program Play:
To check: Press "MEM/REPEAT/ENTER" lightly during programming
before you press . Each time "MEM/REPEAT/ENTER"
is pressed the track number appears in the display
window.
To change: When checking press either or to alter the track
number for the program currently displayed. Press "MEM/
REPEAT/ENTER" to register the newly selected track into
memory.
To delete: When open the CD door including that program will be
cancelled.
SHUFF (Shuffle) Play - Playing the Selections in Random Order
1. Press P. MODE (Play Mode) during play until
"SHUFF" flashes in the display window.
2. Press to begin the SHUFFLE play.
* To locate the beginning of the track being
played: press .
* To locate the next track: press . However,
you cannot locate a previous track even if
you keep pressed.
Repeat Playback (Repeat One and Repeat All)
To repeat the same track
Press MEM/REPEAT/ENTER during play until
" 1" appears in the display window.
Select desired track to be played only once
by pressing or .
To repeat the whole disc
Press MEM/REPEAT/ENTER during play until
" ALL" appears in the display window.
Note:
* Repeat play can be performed during program, intro and shuffle
play.
* The program is also erased when the disc compartment is opened or
the auto power off function turns the power off.
* If the program mode is exited by means of the /OFF key, all the
programs would still remain in memory.
* During the program play, the AMS operates in the programed order.
(AMS-auto music sensor)
DIGITAL ANTI-SHOCK SYSTEM
The Digital Anti-Shock System incorporates a special electronic circuit
that prevents sound from skipping when the unit is subjected to shocks
and vibration during play.
When you start playback, the Anti-Shock System turn on and " "
indicator appears in the display to prevent sound skipping.
When the unit receives a physical shock which prevents the laser pick-up
from "reading" the CD, this system immediately starts playing the sound
stored in its memory and continues until the laser pick-up recovers.
If the unit is subjected to continuous shocks and all the data stored in
memory is used up the sound will skip.
If the vibration stops then the data memory will be restored. If continuous
vibration is applied when the data memory is empty, an error message
" " will be displayed. To reset the CD player press " /OFF" once.
To cancel the Anti-Shock System, press the ANTI-SHOCK button, then
" " indicator disappears in the display
NOTES:
In the "DIGITAL ANTI-SHOCK SYSTEM", battery power consumption
is more because the disc rotates faster than normal and the memory
circuit is active.
When the Digital Anti-Shock System is switched on or off, the sound
will be interrupted for a short time. This is normal.
Under some conditions, noise may be heard or sound skipping may
occur.
-when the disc is dirty or scratched.
-when the disc contains certain signals.
-when the unit is subjected to a certain kind of shock.
In these conditions, try to release "DIGITAL ANTI-SHOCK SYSTEM."
TROUBLESHOOTING GUIDE
Should any problem persist after you have made the following checks,
consult your nearest service facility.
Disc play does not start:
The disc is inserted upside down or incorrectly. Insert the disc
correctly with the label surface up Dusty or defective disc Dirty or
dusty lens. The disc compartment lid is not closed Moisture
condensation -> Leave the unit in a warm place until the moisture
evaporates The AC power adaptor is not plugged into the wall outlet
The unit is not placed on a level surface Weak batteries
No sound from the headsets:
The headphones/earphone plug is not firmly connected to the PHONES
jack Adjust the VOL control Dirty plug
No sound from the connected speakers:
Check the connections The amplifier is not turned on
Skipping of sound:
Dirty or defective disc Dirty lens. Strong vibration
When using with batteries the battery life is short:
Manganese batteries are used. Use alkaline batteries
Display window shows " " error message and the unit cannot
be operated:
No disc , dirty disc or scratched disc. The unit will return to full stop
mode after approx. 30 seconds, or reset the player by pressing "STOP"
once and then insert a disc to start playing.
MAINTENANCE
Cleaning the unit
Do not use volatile chemicals on this unit. Clean by lightly wiping with a
soft cloth.
Cleaning CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc in a circular motion from the centre
out with a cleaning cloth. After playing, store the disc in its case.
Handling the disc
Only touch the CD on the edge to avoid finger prints on its surface. Do
not stick paper or tape nor write anything on the surface.
SPECIFICATIONS
General
Compact disc digital audio system
Digital filter two-time oversampling
Three-spot optical pick up
Output (at 1KHz 0dB level) Line output (stereo minijack)
Output level 0.4V (Rms) at 47KΩ at 1KHz
Headphones/earphone (stereo minijack)
15 mW + 15 mW at 16Ω to 32Ω
Power requirements 2 size AA (LR6 or UM-3) alkaline batteries,
or
DC IN 6V, 450mA power adaptor
Polarity of plug
Operating voltage: U.S.A., Canada:
(AC adaptor) 120V AC 5% 60 Hz
Middle East and Australia:
240V AC 5% 50 Hz
UK and Germany:
230V AC 5% 50 Hz
Chile: 230V AC 5% 50 Hz
Singapore, Malaysia & Thailand:
200-240V AC 5% 50 Hz
Japan: 100V AC 5% 50/60Hz
Frequency range: FM 87.3 - 108.1 MHz
AM 520 - 1720 KHz
Dimensions: Approx. 132 x 147 x 38 mm (w/h/d)
Weight: Approx. 290g (not incl. batteries)
Design and specifications are subject to change without notice.
Printed in CHINA 811-990591-010
Loading...