Portable Compact Disc Player
with Skip Free Protection
CE1000X
INSTRUCTION MANUAL
128-6204
Please read this instruction manual carefully before operating the Compact Disc Player.
WARNING
To prevent fire or shock hazard, do not expose the Compact Disc Player to rain or moisture.
IMPORTANT
Since the CD circuitry may cause interference to other radio tuners nearby, switch the unit off
when not in use or move it away from the affected radio tuner.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
NOTE: This equipment has been tested and found to comply within the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio / TV technician for help.
SAFETY CERTIFICATION
This Compact Disc Player is made and tested to meet safety standards of the FCC, requirements
and compliance with safety performance of the U.S. Department of Health and Human Services,
and also with FDA Radiation Performance Standards 21 CFR Subchapter J.
DANGER
LASER SAFETY
This unit employs an optical laser beam system in the CD mechanism,
designed with built-in safeguards. Do not attempt to disassemble the unit. If
INVISIBLE LASER RADIATION
WHEN OPEN AND
INTERLOCK FAILED OR
DEFEATED. AVOID DIRECT
EXPOSURE TO LASER BEAM.
SAFETY PRECAUTIONS
1. Do not open the Compact Disc Player’s case. Refer servicing to qualified personnel only.
2. Do not expose to excessive heat, direct sunlight, dust, moisture, vibration or shock.
3. Use ONLY the AC adapter provided. Other adapters may damage your unit. Disconnect the
unit from the wall outlet when the unit is not to be used for an extended period of time.
4. When cleaning your unit, use a soft dry cloth, do not use solvents or commercially available
cleaners as they may damage or discolor the finish.
5. Do not wear headphones while operating a motor vehicle, this could create a traffic hazard
and is illegal in many areas.
6. The headphones supplied with your unit provide superior stereo listening while allowing you
to hear outside sounds when listening at a normal low volume level. Listening at extremely
high volume levels can damage your hearing and prevents you from hearing outside noise/
sounds.
7. If you notice that the sound has become weak or distorted, this is an indication that your
batteries are low. Replace the batteries with new or recharged batteries (see "BATTERY
OPERATION")
the unit requires repair, refer to qualified service personnel. Exposure to this
invisible laser light beam may be harmful to the human eye. THIS IS A CLASS1 LASER PRODUCT. USE OF CONTROLS, ADJUSTMENTS OR
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN, MAY RESUL T
IN HAZARDOUS LASER LIGHT BEAM EXPOSURE.
1
LOCATION OF CONTROLS
ON
AC ADAPTOR
POWER SOURCES NORMAL BATTERIES / AC ADAPTER
18
2
3
4
5
6
1. Charge Indicator
2. Skip Up Button
3. Skip Down Button
4. DC Input Socket
5. Battery Door
6. Hold Switch
7. LCD Display
8. Play/Pause Button
12
13
9. Stop Button
10. Anti-Shock Button
11. Program Button
12. Mode Button
13. Door Open Button
14. Bass Boost Switch
15. Phones Jack
16. Volume Control
Battery Power Operation
1. Open the battery compartment cover
7
and insert two "AA" alkaline batteries inside the battery compartment.
Follow the polarity as indicated in the
9
battery compartment.
2. Close the battery compartment
cover.
10
11
Battery Type
Alkaline "AA"
Ni-CAD
Rechargeable
(min specification
recommended
1.2V - 650mA)
NOTE: Zinc/Carbon or Zinc/Chloride type
batteries are not recommended for this unit as
their use will result in extremely short playing
times. To economize on batteries, it is
recommended that the AC adapter supplied
with this unit be used whenever possible.
Average Playing Time
(Continuous Play)
Normal Play Anti-Skip
Mode Play Mode
Approx. 9 hrs. Approx. 8 hrs.
Approx. 3.5 hrs. Approx. 2.5 hrs.
AC Operation
1. Insert the DC plug, at the end of the
14
15
16
AC adapter cord into the DC input
jack on the unit.
2. Plug the AC adapter into a 120V/
50Hz AC power outlet socket.
Note: If the AC plug of this unit does
not fit in your AC outlet, a plug adaptor
(Not supplied) should be used.
Consult your local dealer on the type of
plug adapter required.
LOW BATTERY ALERT
When the battery indicator (Batt.)
appears in the LCD panel, the batteries
are becoming discharged. The CD
player will not function properly and the
batteries must be replaced. If Ni-cd
rechargeable batteries are being used
follow the instructions on how to
recharge the batteries detailed in this
manual.
2 3
INSERT WITH
THE LABEL
FACING UP.
PRESS THE CLAWS
AT THE CENTER OF
THE DISC CASE.
PRESS THE
DISC GENTLY
TO INSERT IT.
LIFT OUT WITHOUT
TOUCHING THE
RECORDED SURFACE.
INCORRECT
CORRECT
FROM THE CENTER TO THE EDGE
INCORRECT
CHARGING AND USE OF RECHARGEABLE BATTERIES
Rechargeable Battery Operation
This unit can fully recharge specified rechargeable batteries, in approximately 15
hours. The rechargeable batteries (NOT supplied) should be recharged before
they are used for the first time, if they are low in power or they have not been used
for a long period (over 60 days).
1. Open the battery compartment cover and
insert two of the recommended rechargeable
batteries, matching polarity. (1.2V 650mA)
WARNING:
OF RECHARGEABLE NICKEL-CADMIUM
TYPE, OTHERWISE THE BAT TERIES
MAY EXPLODE OR LEAK.
2. If you are using rechargeable batteries that
do not have the negative side exposed, you
will need to use the rechargeable battery
sleeve that is initially packed in the battery
compartment as shown in Fig. A. Insert one
rechargeable battery into the battery sleeve
by sliding the negative terminal of the battery
into the sleeve as shown in Fig. B.
3. Insert the two "AA" rechargeable nickelcadmium batteries (not supplied) into the
battery compartment. The battery with the
rechargeable battery sleeve should be
placed in the slot that holds the charge plate
(this is the slot closest to the center of the
unit) as shown in Fig. C.
4. Close the battery compartment door.
5. Connect the supplied AC adapter's plug to
the AC outlet and insert the DC plug into the
DC input jack on the unit. USE ONLY THE
AC ADAPTER SUPPLIED WITH THE SET
FOR CHARGING. NOTE: The charge
indicator will illuminate.
6. After 15 hours, unplug the AC adapter.
7. CAUTION: DO NOT CHARGE
CONTINUOUSLY FOR 24 HOURS OR
MORE. DOING SO CAN CAUSE THE
PERFORMANCE OF THE
RECHARGEABLE BATTERY TO
DETERIORATE.
BOTH BATTERIES MUST BE
RECHARGABLE BATTERY SLEEVE
WITH BATTERY CAUTION SHEET
PACKED BY POLYBAG
CHARGE PLATE
FIG (C)
FIG (D)
A
C
A
D
A
P
FIG (A)
RECHARGABLE
BATTERY SLEEVE
BATTERY
FIG (B)
RECHARGABLE
BATTERY SLEEVE
T
O
R
4
OPEN GAP
MUST BE ON
THE UPPER
SIDE POSITION
8. If the operating time decreases drastically even when the rechargeable nickelcadmium batteries are properly recharged, purchase a new set of rechargeable
nickel-cadmium batteries.
9. When charging for the first time or after a long time, playing time may be reduced.
In this case, charge and discharge the batteries several times.
Remark: The battery adapter is used with standard rechargeable batteries.
Rechargeable batteries with the negative side exposed do not require this
adapter.
LISTENING WITH HEADPHONES
Connect the plug of the stereo headphones into
the PHONES (GREEN) socket.
WARNING: To prevent damage to your hearing,
TO
PHONES
avoid excessive volume levels and listening to
sound for a long period of time when using
headphones.
■ Adjust Volume to the desired level.
HANDLING COMPACT DISCS
This unit is designed to play only compact discs bearing the
identification logo below.
Other discs may not conform to the CD standard and may not play properly.
• Dirty, scratched or warped discs may cause
skipping or noise.
• Handle the disc only by the edges. To keep
the disc clean, do not touch its surface.
• Discs should be stored in their cases after
use to avoid serious scratches.
• Do not expose disc to direct sunlight, high
humidity, high temperatures or dust etc. Prolonged exposure to extreme temperatures
can warp the disc.
• Do not stick or write anything on either side
of disc. Sharp writing instruments or the inks
used in some felt-tip pens, may damage the
discs its surface.
Remove the disc
Hold the edge and gently press the center pivot
as illustrated to pick up the disc.
CAUTION: Wait for the disc to stop rotating
before pressing the OPEN button.
NOTE: This unit can play 3" (8cm) single CDs
without an adapter. Do not use a CD single
adapter for these discs.
5
CLEANING DISCS
• Finger prints should be carefully wiped from
the surface of disc with a soft cloth. Unlike
conventional records, compact discs have
no grooves to collect dust and microscopic
debris, so gently wiping them with a soft cloth
should remove most particles. Wipe in a
straight motion from the center to the edge.
• Never use thinner, benzene, record cleaner or anti-static spray on a compact
disc. Such chemicals can damage its plastic surface.
BASIC DISC PLAY
The Compact Disc Player can play Audio Discs such as CD-Recordables and CDRewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD.
1. Connect the headphones to the PHONES (GREEN) socket.
2. Press the OPEN button to open the CD compartment lid.
3. Adjust the VOLUME to minimum.
4. Insert the disc with the label side facing up.
5. Close the lid securely until a click is heard.
6. Press the PLAY button to start playing.
Increasing the bass
Set the BASS BOOST switch to the ON position.
NOTE: The bass boost performance will be dependent on
the VOLUME control setting.
HOLD Switch
This switch prevents accidental selection of an unwanted
function during Playback or Stop mode. In the HOLD "ON"
position, no function button on the unit can be operated
(except OPEN). Moving the switch to the "OFF" position,
returns the unit to normal operation.
Turning Power on and off
This unit has no ON/OFF switch. To turn on and off, press the following buttons.
To turn on:
Press >II PLAY/PAUSE (playback starts).
To turn off:
Press ■ STOP button once to standby mode.
If press ■ STOP button twice, it will be turn off the power immediately.
Auto power-off function
When the unit is stopped (standby mode) for approximately 30 seconds, the power
is automatically turned off.
6
ON OFF
HOLD
BASS BOOST
OFF ON
LCD DISPLAY INFORMATION
When power is applied to the unit
• If disc is in, auto adjustment is started. During adjustment,
display shows - -.
• If no disc, then disc is displayed. Put the disc and close
the lid, then the player starts auto adjustment again.
• If the lid is opened, the display shows OPEN. Closing
the lid starts auto adjustment.
• If the player can't read the Table of Contents (TOC) then
Er is displayed.
• When TOC data has been read, the display shows
•Track No. 1 plays automatically. ANTI-SHOCK starts
flashing.
• If ANTI-SKIP key is pressed, then
TO PLAY FROM STOP MODE
• Press PLAY/PAUSE button, then the display changes to
01 00:00 and starts play.
• When the memory is full, ANTI-SHOCK stops flashing.
TO STOP
Press STOP key and the TOC is displayed.
TO PAUSE
Press PLAY/PAUSE button, then pause on/off alternately.
When the player is paused the time display is flashes.
flashing.
disappears.
7
REPEAT/PLAY MODES
INTRO PLA Y
Every time the MODE button is pressed, the corresponding mode appears in the
display window.
MODE MODE MODE MODE
NORMAL
REPEAT
1
REPEAT
ALL
INTRO
RANDOM
When this is showing on the
LCD display. The current track
on the disc will be repeated.
When this is showing on the
LCD display. All tracks on the
disc will be repeated.
NOTE: In normal mode none of the above symbols show in the display.
During playback
MODE
During playback
MODE
X 1
X 2
NORMAL PLAYBACK
Plays the entire disc.
A indicator appears on the display when the
batteries need to be changed.
1. Press MODE button three times, then INT is displayed.
2. Press PLAY / PAUSE button, and starts INTRO play
from track no. 01.
3. Select INTRO mode during play, INT will flash.
• Press PLAY/PAUSE button, INT stops flashing and
INTRO play from track no. 01.
• Press >>I to hear the INTRO to the next track.
• Press I<<, to hear the INTRO of the previous track
PROGRAM PLAY
This allows selected tracks on the disc to be played in any order desired.
To set the program play
• Programs can be set in the STOP mode or normal play mode.
1. Press the PROG button, then PRG and starts flash.
2. Press I<< or >>I to select the desired track.
3. When desired track is displayed, press PROG button to
register. Then track No. display change to 00 again.
4. Repeat step 2 and 3 to program the order of more tracks.
Up to 20 tracks can be programmed into memory.
To complete programming and start play
Press PLAY/P AUSE button, then PRG stops flash and starts
play soon.
To clear programming
• Set the first program track to 00 and press the PLAY/PAUSE (>II) button.
• Open the door.
• Power Off
8
9
RANDOM PLAY
MAINTENANCE
Enables all the tracks on a disc to be played in a Random (Shuffle) sequence.
1. Press MODE button four times, then RND is displayed.
2. Press PLAY/P AUSE button, then the track No. is selected
at random and starts play.
3. To select RANDOM mode during play, press the MODE
button until RND starts to flash.
• Press PLAY/PAUSE button or I<< or >>I, and begin
RANDOM play.
SKIP AND SEARCH FUNCTION
Locating a Particular track
To go back to the beginning of the
current or a previous track.
To go to the beginning of following
tracks
Locating a Particular Point in a track
To search backwards within a track at
high speed.
To search forward within a track at high
speed
Low level audio will be heard during the search process to assist in locating the
correct point in the track.
Press I<< lightly and repeatedly.
Press >>I lightly and repeatedly.
Keep I<< depressed
Keep >>I depressed
Cleaning the Case
Wipe with a soft cloth. If the case is very dirty, dampen the cloth with a weak
solution of neutral detergent and water, and then wipe clean.
Cleaning the Lens
A dirty lens will cause sound skipping and, if the lens is very dirty, the CD may not
work. Open the disc cover and clean the lens as described below.
• Dust or Dry Particles
Using a camera lens brush/blower, blow on the lens couple times, then wipe it
lightly with the brush to remove dust. Then, blow on the lens once more.
• Fingerprints
If the lens cannot be cleaned by using a brush/blower, use a dry cotton swab
starting in the middle and working to the outside edge.
1110
USING ANTI-SHOCK AND SKIP FREE PROTECTION FEATURE
PRODUCT SPECIFICATIONS
Note the " " indicator appears on display as being empty when the player is first
activated. It immediately begins to store sound data in the memory bank, the
indicator appears to be "
When the laser loses tracking due to mechanical shock, the data stream into the
memory is interrupted but the data output from the memory buffer continues, so
the sound is not interrupted. As the data is read from the memory, the indicator
changes from "
Once the laser locks again on the CD track, the data stream is fed to the memory
and joined to the previous data (see indicator changes) at higher speed, this provides
higher level shock protection than the traditional one.
CAUTION
If the unit is subject to excessive and continuous repeated shock, it will cause the
sound skip. Also note the "
NOTES
• When the "ANTI-SHOCK" is operating, the battery consumption is higher
because the disc rotates faster than normal and also the memory circuitry is
activated.
• When the digital anti-skip function is switched "ON" or "OFF", the sound will be
interrupted. This is a normal occurrence.
• Remember that conditions such as dirty, scratched or warped discs may cause
skipping or noise, thereby affecting performance of the "ANTI-SHOCK" system.
" when the data buffer is full.
" to " ".
" indicator will appear empty.
PICK UP
System Compact disc digital audio system
Laser diode Material : GaAlAs
Properties Wavelength: λ = 780nm
Emission duration : continuous
Laser output: < 44.6µW
Error correction Cross-interleave Reed-solomon code
AUDIO
D/A conversion DAC four times oversampling
Frequency response 20-20,000Hz (+1/-3 dB)
Wow and filter Below measurable limits
No. of channels 2 Channel (stereo)
Output level Headphones : 20mW (32Ω)
Bass boost effect (100Hz) +8 dB
GENERAL
Power requirements - 2 x LR6 "AA" alkaline battery
- DC in 6V jack accepts AC power adapter
(centre positive)
Power consumption 0.8W (DC 3V) under normal condition
Dimension Approx. 128 (W) x 28.5 (H) x 137 (D) mm
Weight Approx. 200g not including battery
12
13
Loading...