Audiovox ACC-52 User Manual

OWNER'S MANUAL

AND

INSTALLATION GUIDE

OPEN

MODEL ACC-52

REMOTE-CONTROL

10-DISC CD CHANGER

INTRODUCTION

Congratulations on your purchase of this remote mount 10 Disc CD Changer. It allows you to easily upgrade your existing car stereo system to the quality of Compact Disc entertainment. The entire system plays through your FM Stereo car radio and stereo speaker system - there’s nothing else to add or replace. Best of all, the CD Changer is easy to install. There are only three wires to connect and four simple plug-in cables. Just follow the simple step-by-step instructions that follow.

FEATURES

n Remote mount changer holds up to 10 compact discs n Remote control with back-lit LCD panel, displays disc, track and function n Remote controls include forward and reverse track and disc search, track and disc scan, shuffle and

repeat play plus high speed audible cue and review search

n Advanced technology includes 8x oversampling digital filter and twin 1-bit digital/analog converters n The special design allows horizontal, vertical or 45-degree mounting.

TOLL-FREE ASSISTANCE

The installation and connections are so simple we doubt you’ll need our help, but if you do, we’re here to help you. Just call our toll-free assistance line at 1-800-645-4994 during the days/hours shown.

TIME ZONE

DAY

MON. - FRI. SATURDAY

PACIFIC

5:30AM - 4PM 6AM - 2PM

MOUNTAIN

6:30AM - 5PM 7AM - 3PM

CENTRAL

7:30AM - 6PM 8AM - 4PM

EASTERN

8:30AM - 7PM 9AM - 5PM

INDEX

Introduction and Contents Page 2 Mounting the Remote Control Page 12

Packing List Page 3 Remote Control Operating Instructions Page 13 Before Installing the Unit Page 4 Hints for Correct and Safe Operation Page 15 Where to Install the Changer Page 5 Handling the Discs Page 15 Installation Page 6 Use of the CD Magazine Page 16 Overall Wiring View Page 9 CD Changer Operating Instructions Page 17 Wiring the CD Changer Page 10 Specifications Page 17

Troubleshooting Page 18

PACKING LIST

MAIN UNIT

Changer

OPEN

INST ALLA TION PARTS

Bracket (L)

1 pc.

Bracket (R)

1 pc.

Hexagonal bolt with washer

(M5 x 10)

7 pcs.

Remote Control

Screw (C)

Phillips Head Self-Tapping

Screw

(M3x12)

2 pcs.

FM Module

5 Meter Din Cable

1 pc.

Self-tapping screw

(M5 x 12)

4 pcs.

OTHER ACCESSORIES

CD Magazine (P/N ACC-52MAZ)

1 pc.

Seals (A)

1 pc.

Index label sheet

1 pc.

Seals (B)

1 pc.

Owner's Manual

and Installation Guide

1 pc.

BEFORE INSTALLING THE UNIT

Transport Lock Screws

The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation.

l Caution l

After removing the transport lock screws, place the supplied seals (A) over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction.

Installation and Wiring Precautions

To prevent a short-circuit,

l Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation. l Connect power wires last.

Note

If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation not to cause a short circuit.

Do not install the unit in the following locations.

l Locations exposed to direct sunlight. l Where hot air is discharged from the car heater. l In areas subject to extreme temperatures.

TRANSPORT LOCK SCREWS (2 RIGHT SIDE, 1 LEFT SIDE)

Incorrect installation can cause the sound to "skip" when playing a disc.

Mount the unit firmly in place, using the supplied brackets and screws.

Be careful not to damage the car wiring.

l Be sure to use the supplied screws.

l Be careful not to snag any wires when tightening screws. l Do not use any of the screws that are part of the brake or steering system, to install the unit.

l This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning

of the mechanism.

ADDITIONAL 10-DISC MAGAZINES

Additional CD magazines are available as an accessory item (Part No. ACC-52MAZ) from the store where your ACC-52 was purchased. If they are out of stock, you can order them direct from Audiovox. Send a check or money order (do not

send cash) made payable to Audiovox Corp in the amount of $49.95 (U.S. Currency) to:

Audiovox Corp. 150 Marcus Blvd. Hauppauge, N.Y. 1 1788 Attn: Parts Department

NOTE: New York residents, please include applicable sales tax.

WHERE TO INSTALL THE CHANGER

The ACC-52 changer is designed for horizontal (flat), vertical (upright) or 45-degree mounting. It must never be mounted upside-down or on either one of it's sides as explained previously. A few of the many mounting possibilities are shown below. The following precautions must be considered when selecting the mounting location:

1. Fuel Tank - Never install above your fuel tank as the holes you must drill may pierce the tank or the fuel lines. Also check for other obstructions such as wires, etc.

2. Excessive Heat - Avoid areas exposed to direct sunlight (on top of rear package shelf) or next to your car heater’s output ducts.

3. Ease of Use - Make certain the changer is easily accessible for loading and unloading the CD magazine.

4. Distance - The data cable that joins the changer to the FM module is 15 feet long. Do not exceed this length.

5. If mounting to a plastic surface, do not use the self-tapping screws provided. Use the bolts and hex nuts provided for a more secure installation. IMPORTANT: Failure to properly secure the CD changer is the most common cause of all “skipping” and related

CD play problems. Changer must be mounted as explained on the following pages.

MOUNT ON SIDE OF TRUNK SIDEWALL

MOUNT UNDER LIP OF TRUNK

TRUNK MOUNTING (SEDANS)

This is usually the easiest location to use as there is ample space available. Check that you do not interfere with the removal of your spare tire, etc. Observe caution on fuel tank stated above. The only negative aspect is the need to route the wiring from the trunk to your car dashboard.

HATCHBACKS, WAGONS & VANS

A simple investigation of the areas shown will often provide several possibilities. Observe caution on fuel tank stated above and make sure the unit is protected from cargo, passenger entry and exit, etc.

UNDER PASSENGER’S FRONT SEAT/BEHIND SEAT

If sufficient space and easy access exist, the area under the passenger's front seat is ideal, and will also allow easy wiring access. However, you may need to temporarily remove the seat for ease of installation. The area behind either the passenger’s or driver’s seat on pickup trucks is another ideal location.

MOUNT ON FLOOR OF TRUNK (HORIZONTAL OR 45 DEGREES)

MOUNT ON SIDEWALL OF CARGO AREA

MOUNT ON BACKWALL OF HATCH AREA

MOUNT UNDER SEAT

MOUNT ON BULKHEAD BEHIND SEAT OF PICKUP TRUCKS

INSTALLATION

The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip.

CAUTION: After setting the built-in anti-vibration springs, place the supplied Seals (B) over the holes. These seals are used

to keep dust, which could cause a malfunction, out of the unit.

HORIZONTAL INSTALLATION

Set the left and right anti-vibration springs to position "H".

VERTICAL INSTALLAITON

Set the left and right anti-vibration springs to position "V".

45° ANGLE INSTALLATION

Set the left and right anti-vibration springs to position "45°".

position "H"

position "V"

PROCEDURE FOR HORIZONTAL INSTALLATION

Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10)

5 4

NOTE: Use seals (A) to cover unused

Anti-vibration springs position

mounting holes on sides of unit.

Bracket (L)

Bracket (R)

position "45°"

45°

Hexagonal bolt (4) with washer base (M5 x 10)

Determine the mounting location, and drill four mounting holes.

Never mount the unit near the fuel tank.

Secure the unit in place, using four self-tapping screws (M5 x 12). Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion.

Bracket (L)

Drill holes 4mm in diameter.

Self-tapping screw (M5 x 12)

Bracket (R)

+ 14 hidden pages