Audiovox ACA250 User Manual

AUDIOTOX*

ELECTRONICS CORP.

Vehicle Wireless Rear Observation System

Model: ACA250

Installation/User Manual

For Customor Sorvico

Visit Our WebsUe At

www.audlovox.com

Prcxkict Information. Photos.

FAQ's Owner's Manuals

02008AudiovosElcclroDicsCorp., ISO Marcus Blvd.. Hauppauge. N.Y. 11788

Features:

• 2.5** LCD Color Display with Night Vision

• 2.4 GHz Wireless Receiver and Transmitter

• Automatically Displays Image when Vehicle is in Reverse
a Monitor Mounts on Dash or Windshield

• NigfiiAssiai Vis lull wUli IR LEDS

Inatallatlon Manual
Modal Numbar: ACA250
SIza:
Matarlal:
Color:

PJetura color:
Part Numbar:

Ratio:
DATE:

$.12*(Wldth) X 7.48*(Langth)

Both*$ida coated papor. GSm: 127g
WHITE 6ACKGROUNO/BLACK LETTERING

BLUE Color- (Pantona#:CMYK 100.85.10.0)
REOColor-(Pamone#:CMYK 0.97.100.0)
CMYK printing
Z0276ACA2SOM8UM

1:1

12/07/2008

TABLE OF CONTENTS

Warnings
Product Description
Packing List
Installation Instructions

Monitor Installation

Camera Installation
Operating the System
Testing the System
Specifications
Maintenance
Troubleshooting

Fe

1) Thu device compiks with pan IS of FeC Ruk».
Operation a suii^cct to the following two condition (I)
thn device тлу not саше harmfol imcffertnce. and (2)
thb device must accept anjr interforence received.
IjkJ tiding iAterfofcAce due may саше undeured
operation.

2
3
3
4
4
6
8
9
9

10
10

Product name: WIRELESS BACKUP SYSmi
Model No.: ACA250

Fee ID: UZRACA250

2) Changes of modi6catioiu not expressly approved by the
рапу responsible for compliance could void die usee's

authority CO operate the equipment.

Warnings

This product IN intended to assist in safe driving and to allow the
driver to have a broader rear view while the vehicle is in reverse.
You. as the driver, are solely responsible for the safe operation of
your vehicle and the safety of your passengers according to your
local traffic regulations. Do not use any features of this system to
the extent it distracts you from safe driving. Your first priority
white driving should always be the safe operation of your vehicle.
Audiovox Electronics Corporation cannot accept any
responsibility whatsoever for accidents resulting from failure to
observe these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized
modifications or damage to the product may result in

electrical shock. Handle all components with care. Inspect
regularly for damage to components and cabling.

2. You arc responsible for ensuring that the installation of this
product docs not void or affect the vehicle manufacturer’s

warranty. Audiovox Electronics Corporation or its
subsidiaries arc not liable in full or in part for improper
installation resulting in loss or damage to your property, or
for voiding all or pan of the vehicle manufacturer’s warranty.

3. Do not apply excessive force to any of the components

contained within this kit. Excessive force used before,
during or after installation that results in a damaged or non

functional part will void all warranties.

4. Please follow the procedures in this installation manual.

Improper installation or modification of this product will
void all warranties.

Many jurisdictions have laws and regulations relating to the use of
cameras and some do not allow for the obstruction of information

contained on a license plate. Before using this product, it is the
buyer’s responsibility to be aware of and comply with any
applicable laws and regulations that apply to license plates or may
prohibit or limit the use of cameras.

Product Description

The ACA2S0 Wireless Vehicle Rear Observation System is designed
to assist the driver by providing a clear and wide image of the area
behind the vehicle whenever the vehicle is shifted into reverse. Never
rely solely on this product to ensure the area is clear of children
and/or obstructions. Use your monitor and look both ways. This
product is not intended to replace existing safety procedures, but
rather to add an additional safety tool for your vehicle.

CAUTION: Do not back up your vehicle while watching the
monitor screen. Always look in the direction the vehicle is traveling.
Use the monitor as an aid to ensure there are no children or
obstructions. The image on the monitor is not designed to show
distance and may be misleading. The actual distance is less than
appears in the monitor. The range of the image is limited. Be aware of
blind spots.

Packing List

The model ACA*250 monitor package consists of the following
items:

1. LCD Wireless Reception Monitor • I qty Part # 30702030

2. Wireless Camera • I qty Not Available Separately

3. 2.Sm Power Supply Cable for Monitor qiy Part # 30702200

4. 2.SmPowcr Supply Cable for Camera - I qty Part M 30702190

5. 2.5m Cigarette Lighter Cable-I qty Part #30702210

6. Hardware Bag Contains: Part #30502210
a) 6mm x 30mm Bolts *2 qty
b) 6mm Nuts -2 qty
c) 6mm Flat Washers *4 qty
d) 6mm Lock Washers *2 qty
e) Tap Connectors *2 qty
ODouble Sided Mounting Tape «Iqty

7. Insiallation^Users Manual -1 qty Part # 30702020

Installation Instructions

CQMPLETELYJtEAD THIS MANUAL BEFORE

INSTALLATION

NOTE: Wc have included all of ihe items needed for most standard
installalions, but all vehicles are different. We recommend you review
your vehicle completely before starting.

MonUor Installation

jVouníiñg fhf Monitor

The monitor with flexible mounting pad and double sided tape mounts on
either the vehicle windshield or dashboard.

Note: Tkt douhU sidtd tape supplied is extremely strong. Be sure of the

position before mounting.

1. Choose a monitor location in your vehicle that does not block your
view and complies with local laws for safe driving..

2. Clean the monitor base and mounting area with a cleaner that does
not leave a residue.

i. Remove the protective film from one side of the double sided tape

and apply to the bottom of the monitor base. Next, remove the
protective film from the other side of the double sided tape and
carefully position the monitor and press into place.

CAUTION: Insure that all wires arc run safely and do not interfere

with Airbags, Safety Devices« or any other equipment.

a) Choose a source that only has power when the vehicle ignition is

on. Check with a meter or test lamp (can be purchased at an auto
parts store). Af)er determining your power location; turn off the
ignition and disconnect the battery to insure your safety.

b) The Red wire on the Monitor Power Harness is the ignition or 12

volt lead. This roust be connected to the power source or fuse box
location that you have chosen to use. Insure the connection is
covered or protected so it can not short circuit.

c) The Black wire on the harness is to be connected to any * 12 volt

ground lead or a solid metal location in the vehicle. Also test your
location to insure a good solid ground. Just because it is metal
does not mean it is a good ground.

d) Plug the power plug into the monitor power supply jack.

After the monitor Installation is complete remove the protective plastic
cover from the panel.

Figure i (Electrical Connections)

-i

FUSCtXS)

- [

У

FUiCOA)

sucKChMUi/arseAe

-

aen* lavoc i^use ssoks

LIsaWf AdJWUr

Electrical Connections

The monitor can be powered two ways:

1« Cigarette Lighter Adapter: Plug the cigarette lighter adapter into

the vehicle's eigereitc lighter socket« end then insert the 2.5mia

plug into the power supply jack on the monitor.

2.Advanced Hard Wire Installation: Audiovox recommends using
a qualified professional for the Hard Wired cable installation.

NOTE; When using the Cigarette Lighter Adapter, if the Red Power
Indicator stays on after you turn your ignition key off, you will want to
unplug the adapter to insure that your vehicle battery does not run
down when parked for extended periods of time.

To replace the fuse in the Cigarette lighter adapter« unscrew the tip.
Replace only with the same rating of fuse or damage may incur.

CimcriJpsuiilmioo

1. Remove the rear iiccosc pUlc to determine ihe best way to run the
power wires to the reverse lights. It ia important to use the Reverse
lights and not the License Plate illumination lamp or any other. Tbe
system is designed to come on when the vehicle is in reverse gear
only. Improper installation can cause the system to not work or to run
at undesired times.

Note: Ail vebieles are designed differently. We offer some general
installation advice here* but check and rc«check you iDStallalion before

starling. Some vehicles may have the license plate on the tailgate and the

Reverse lights may be located on the vehicle pillar. In this case you will
need to study your vehicle closely to determine the best route for the power

wire. In some vehicles you may need to eatend the power wire to reach the

reverse lamps. Power wire can be purchased at an auto parts store or
hardware store if this is needed. Most installations can be completed by
running the power cable behind the trunk or tailgate rubber gasket, tucking
it under the interior trim panel and either connecting at the back of the
reverse lamp in the trunk or removing the reverse lamp assembly (the same
procedure as required to replace the light bulb).

2. The camera cable can be routed as recommended above or
through an existing wire grommet to reach the interior of the vehicle.
If an existing grommet is not available to use. you can drill a bole
behind the license plate to access the vehicle. Purchase a rubber
grommet from an auto parts store to protect the wire from tbe sharp

edges of s bole if you drill one.. The rubber grommet must be a
minimum of 13/32* to allow tbe wire and fuse holder to pass through
it.

Be sure to check behind the intended drilling location before drilling
to ensure no wires or mechanisms interfere or could be damaged
during drilling. Check for interference with license plate lights and
the hatch release switch or mechanism. If not using an existing
factory grommet, drill a bole to match the rubber grommet size that
you intend to use (13/32* minimum) at the selected location near the
vehicle's rear license plate. Route the camera cable connector
through the grommet and insert the grommet into the hole to prevent
water from entering into the vehicle.

3. Now leave enough wire to route behind the license plate. Place the
license plate over tbe opening and line up the holes. Fasten the
camera mounting bracket and the license plate to the vehicle. Use
either the lower mounting holes or the upper on the license plate
making sure that you do not block any information on your plate that
is required by your state laws to be shown.

4. Continue to run the power harness for tbe camera to the vehicle's
reverse lamp. NOTE: Ifthis isa veryshortdistance.be sure to extend

the power cable that comes attached to the camera completely. The
antenna for the camera is located in the harness.

5. Locate the reverse lamp to the tail light assembly. Generally the
Positive wire on the reverse lamp will be a colored wire and the
Negative will be a Black wire. If you would like to insure the wires
are correct; with the vehicle on a level surface, first engage the
emergency brake on the vehicle and place blocks behind the wheels.
Make sure the car is not running but the ignition is switched on and
have another person engage the brake pedal, shift into reverse and
insuring your safety, check the wires with a test lamp. NEVER
ATTEMPTONAHILLORGRADE.

Once you have confuaicd the po»iiivc and negative conncetioa point,

place the vehicle in park, shut off the ignition, and proceed.

Wiring tht Camera to the Vehicle'» Reverse Lamp

1. Locale the reverse lamp in the tail light assembly.

2. Using the tap connector supplied, perform the following steps:
a) Place the un«siripped positive lead from the tail lamp in the run

channel, which runs completely through the connector.

b) Insert the un*strippcd red power wire from the camera completely

into the other channel in the connector.

c) Make the connection between the wires by crimping down the metal

connector with a pair of pliers, making sure the metal is flush with
the plastic insulator.

d) Close the top plastic hinged cover until latched.

3. Attach the black wire from the camera to the negative lead of the lamp

by repeating the abo%'c procedure.

Operating the System

Testing the System

To test the Wireless Vehicle Rear Observation System installation,
perform the following steps:

1. Set the parking break.

2. Start the vehicle.

3. Shift the vehicle into reverse.

4. Verify that the monitor displays the image from the rear camera.

If the monitor does not operate, refer to the trouble shooting section of

the manual.

ISgecifications

GeaernI

Power Supply DCI2V
Power Consumption
Correat Draw <400 mA

Opera ting Tempers lure Range
Fuse 2 Amps

<dW

Otto

sox:

The Wireless Vehicle Rear Observation System operates when the
vehicle is shifted into reverse. The Camera transmits a clear and wide
image from the area behind the vehicle to the Monitor inside the vehicle.
The monitor, when powered, remains in sleep mode until it receives a
video signal on the 2.4GHz fretjuency. When the monitor receives a
video signal, it automatically turns on and displays the image from the

camera.
The monitor automatically adjusts for color, brightness, and contrast, for
either daytime viewing or night time viewing. There arc no user
selectable adjustments.

In conditions such as at night, the camera will automatically switch to
Night Vision Assisted Mode. The picture will look more like a Black &
White image, this is due to the low light level and is normal.
Note: Because this is a wireless system, the monitor is always watching
fora video signal. It is possible to receive signals from other cameras.
Systems such as Security camera's. Baby monitors, and even other Back
up camera systems can trigger the monitor to briefly turn on. This is
normal for wireless products.

Display System

Screen 2.5* LCD Color
Night Vision

Brightness
Contrast Ratio

Backlight Life
Resolution

Video Fomat NTSC/PAL
Display Formal

Wireless Reception System

Operating Frequency

IR LED Assisted

400 Cd/H*

l$0:l
10000 hours

000X234

16:0

2.4CHZ

Maintenance

Though your monitor requires little care, you will still need to maintain

its condition and performance by following the guidelines below.

• Keep your system away from cacessivc moisture, extreme beat
or cold.

• Keep liquids away from the display.

• Occasionally clean the surface of the monitor with a soft cloth
moistened with water or glass cleaner.

Troubleshooting

Symptoms

The Monitor is not on
After the vehicle is
started and the vehiete
is in reverse

Video imafc is not sharp
enough

The Monitor Suys on all
the lime, or runs when the
vehicle is not in reverse.

The monitor is very dark
or ibe image changes
slowly

Solutions

1 .Check the monitor wiring and connections

2. Cbcck the fuse in the Cigarette lighter adapter

3. Cbeck the power connection on the camera
at the reverse lamp

Clean the camera lens with a soft cloth.

The Camera is not wired correctly, if the camera
continues to transmit while not la reverse gear.
re*cbcck your wiring at the reverse lamp.

Inextreme cold or hot conditions the LCD screen
may react slowly. This is normal and will clear as
the vehicle cools or warms to a normal
temperature

10

^INSTALLAnON

rxceiftnct

Three easy steps!

1. Visit www.jensen.com.

2. Click on the Victory Technology
Installation Excellence Logo as

shown above.

3. Enter your product serial number
(example: xxxx_xxxxxxx_xx).

4. Follow the on-screen steps

to download the Installation

Excellence program! ^■ ■ a

12

^

ii^SiaLL/