Audio-Technica BP892CH-TH Datasheet

BP892 & BP892-TH
MicroSet® Omnidirectional Condenser Headworn Microphones
BP892cT5, BP892cT5-TH – Terminated for Lectrosonics using TA5F-type connector BP892c, BP892c-TH – Unterminated
Model numbers ending in ”TH“ are beige. Audio-Technica mentioned herein may be trademarks and/or service marks of their respective owners.
Operation and Maintenance
The BP892 requires 11V to 52V phantom power for operation.
®
is a registered trademark of Audio-Technica. Other product and company names
broadcast & production microphones
®
wireless systems
Features
• Industry-standard sound quality—extremely intelligible natural audio for stage/television talent, lecturers, houses of worship
• Microphone diameter of just 2.6 mm for the ultimate in low-prole, high-performance audio
• Comes equipped with AT8464 Dual-Ear Microphone Mount that converts single ear-worn MicroSet to a dual-ear-worn unit for maximum stability and comfort
• Locking 4-pin microphone output connector compatible with included power module and all Audio-Technica UniPak wireless transmitters
• UniSteep
®
lter provides a steep low-frequency attenuation to
®
body-pack
improve sound pickup without affecting voice quality
• Offered in black and beige (-TH) models
• Also available in wireless models (without power module) terminated for use with all Audio-Technica UniPak
®
wireless
systems and many other manufacturers' wireless systems
BP892 Description
The BP892 is a headworn condenser microphone with an omnidirectional polar pattern. It is designed to provide intelligible natural audio for stage and television talent, lecturers and houses of worship.
The microphone requires 11V to 52V phantom power for operation.
The microphone includes a 1.4 m (55") permanently attached miniature cable. Its free end connects to the provided AT8539 power module via a locking 4-pin connector. The connector is also compatible with all Audio-Technica
®
UniPak
body-pack transmitters. The output of the power module is a 3-pin
XLRM-type connector.
A recessed switch in the power module permits choice of at response or low-frequency roll-off (via integral 80 Hz high-pass UniSteep
®
lter) to help
control undesired ambient noise.
The microphone comes equipped with a power module, a cable clip, a dual-ear mount, two windscreens, two element covers, a moisture guard, a belt clip and a protective carrying case. The microphone is available in black and beige.
Wireless MicroSet
®
Description
The microphone is also available in a variety of terminations for use with Audio-Technica and many other manufacturers’ wireless systems (see below). No power module or belt clip is included (or required) with the wireless models. The wireless models’ dimensions, polar pattern and included accessories are otherwise identical to those of the BP892.
The BP892cW is also available unterminated as the BP892c.
Output is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive acoustic pressure produces positive voltage at Pin 2.
An integral 80 Hz high-pass UniSteep
®
lter provides easy switching from a at frequency response to a low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close vocal use. It also reduces the pickup of low-frequency ambient noise (such as trafc, air-handling systems, etc.), room reverberation and mechanically coupled vibrations. To engage the UniSteep
®
lter, use the end tip of a paperclip or other small
pointed instrument to slide the switch toward the “bent” line.
The exible design of the BP892 MicroSet enables it to be worn on either the left or right ear. Position the lightweight contoured loop around the back of your ear, so that the boom extends from the bottom of your ear. Bend the loop as needed to achieve a secure, comfortable t, so that the MicroSet is not dislodged by shaking your head. Remove the MicroSet and bend a gentle curve in the microphone's boom. Hook the MicroSet back around your ear, and adjust the boom as needed to follow the contour of your face, positioning the microphone near the corner of your mouth. The microphone has a large acoustical sweet spot; experiment with placement near the corner of your mouth for optimal performance.
A cable clip is provided for strain relief, allowing the microphone to remain securely in place without the weight of the cable pulling on the headset. To install the cable clip, slip the cable into the snap-on connector and attach the clip to clothing, leaving enough slack on the MicroSet side of the clip to allow for free, comfortable motion.
The included AT8464 Dual-Ear Microphone Mount allows you to convert your single ear-worn BP892 MicroSet
®
to a dual-ear-worn unit. The BP892 ts on either side of the Dual-Ear Microphone Mount, allowing the microphone to be worn to either the left or right of your mouth. The headband easily adjusts to t both children and adults.
How to use the Dual-Ear Microphone Mount
1. Insert the rounded end of your BP892 ear hook into the larger opening of your Dual-Ear Microphone Mount’s left or right tapered holder. Firmly seat ear hook in the tapered holder.
2. Insert the small rounded end of the additional supplied ear hook into the larger opening of your Dual-Ear Microphone Mount’s remaining tapered holder. Firmly seat ear hook in the tapered holder.
3. Open the Dual-Ear Microphone Mount’s adjustable behind-the-neck headband to its maximum position by pushing the headband’s adjusting tabs together (a). Put the behind-the-neck headband on, hooking the ear hooks over your ears. Adjust the t of the headband as needed, by sliding the headband’s adjusting tabs until you arrive at a secure, comfortable t (a). Attach the microphone cable to the cable clip positioned between the headband’s adjusting tabs (b).
Cable Terminations BP892cW, BP892cW-TH – Terminated with locking 4-pin connector for use
with A-T UniPak® body-pack transmitters
BP892cH, BP892cH-TH – Terminated for ATW-T6001 body-pack transmitters BP892cL4, BP892cL4-TH – Terminated for Sennheiser® wireless systems
using Lemo® connector BP892cLM3, BP892cLM3-TH – Terminated for Sennheiser® wireless systems using locking 3.5 mm connector BP892cT4, BP892cT4-TH – Terminated for Shure® wireless systems using TA4F-type connector
3
a
b
2
1
BP892 & BP892-TH
12" or more on axis
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50
200
10k
5k
1k
500
2k
20k
Roll-off
4
1
Wireless Termination Diagrams
The donut-shaped moisture guard is provided to protect the element from sweat and moisture. Position the moisture guard as close to the element as possible to provide maximum protection. To remove the moisture guard, rst remove the element cover and place it out of harm’s way. Gently slide the moisture guard over the element. Replace the element cover.
Avoid leaving the microphone in the open sun or in areas where temper­atures exceed 110° F (43° C) for extended periods. Extremely high humidity should also be avoided.
4 3
BP892cW, cW-TH
Function Wire Color
Pin 1 Ground/Shield Green Pin 2 Instrument Jumper to Pin 1 Pin 3 Mic Audio Copper Color Pin 4 Bias + In Red
5
3
BP892cT5, cT5-TH
Function Wire Color
Pin 1 Ground/Shield Green Pin 2 Bias + In Red Pin 3 Mic Audio Copper Color Pin 4 Source Load Jumper to Pin 1 Pin 5 Line In Open
1
4
2
3
BP892cH, cH-TH
Function Wire Color
Pin 1 Ground/Shield Green Pin 2 Instrument Jumper to Pin 1 Pin 3 Mic Audio Copper Color Pin 4 Bias + In Red
1
2
BP892cLM3, cLM3-TH
Function Wire Color Sleeve Ground/Shield Green Ring Mic Audio Copper Color Tip Bias + In Red
sleeve
1
3
2
2
BP892cT4, cT4-TH
Function Wire Color
Pin 1 Ground/Shield Green Pin 2 Bias + In Red Pin 3 Mic Audio Copper Color Pin 4 Source Load Jumper to Pin 3
ring
lip
BP892cL4, cL4-TH
Function Wire Color
Pin 1 N/C Open Pin 2 N/C Open Pin 3 Bias + In, Red
Mic Audio Shell/Case Ground/Shield Green
4
1
Specications
23
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio
Phantom power requirements
Current consumption
Voltage range
Switch Weight
Dimensions
Output connector (power module)
Cable
Audio-Technica case style
Accessories furnished
BP892
Fixed-charge back plate, permanently polarized condenser Omnidirectional 20-20,000 Hz 80 Hz, 18 dB/octave (wired only) –49 dB (3.5 mV) re 1V at 1 Pa 250 ohms (wired only) 135 dB SPL, 1 kHz at 3% T.H.D. 104 dB, 1 kHz at Max SPL (wired only)
1
63 dB, 1 kHz at 1 Pa 11-52V DC, 2 mA typical (wired only)
0.1 mA typical at 5V (wireless only)
2.5-11V (wireless only) Flat, roll-off (wired only) Microphone, boom & earpiece:
2.6 g (0.09 oz) Power module (wired only): 85 g (3.0 oz) Microphone: 8.1 mm (0.32") long,
2.6 mm (0.10") diameter Boom: 98.4 mm (3.87") long,
1.07 mm (0.04") diameter Power module (wired only): 97.6 mm (3.84") long, 18.9 mm (0.74") diameter Integral 3-pin XLRM-type
1.4 m (55") long (permanently attached to microphone), 1.6 mm (0.06") diameter, 2-conductor shielded cable with locking 4-pin connector (wired only) M31
AT8539 power module (wired only); AT8440 cable clip; AT8464 dual-ear mount; two AT8157 windscreens; two AT8156 element covers; moisture guard; belt clip (wired only); carrying case
To reduce the environmental impact of a multi-language printed document, product information is available online at www.audio-technica.com in a selection of languages.
An de réduire l’impact sur l’environnement de l’impression de plusieurs, les informations concernant les produits sont disponibles sur le site www.audio-technica.com dans une large sélection de langue.
Para reducir el impacto al medioambiente, y reducir la producción de documentos en varios leguajes, información de nuestros productos están disponibles en nuestra página del Internet: www.audio-technica.com.
Para reduzir o impacto ecológico de um documento impresso de várias linguas, a Audio-Technica providência as informações dos seus produtos em diversas linguas na www.audio-technica.com.
Per evitare l’impatto ambientale che la stampa di questo documento determinerebbe, le informazioni sui prodotti sono disponibili online in diverse lingue sul sito www.audio-technica.com.
Der Umwelt zuliebe nden Sie die Produktinformationen in deutscher Sprache und weiteren Sprachen auf unserer Homepage: www.audio-technica.com.
Om de gevolgen van een gedrukte meertalige handleiding op het milieu te verkleinen, is productinformatie in verschillende talen “on-line” beschikbaar op: www.audio-technica.com.
Audio-Technica Corporation audio-technica.com ©2016 Audio-Technica P52603
In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry
1 Pascal = 10 dynes/cm
1
Typical, A-weighted, using Audio Precision System One.
Specications are subject to change without notice.
frequency response: 20–20,000 Hz polar pattern
50
200
100
12" or more on axis
LEGEND
Roll-off
professionals on request.
2
= 10 microbars = 94 dB SPL
500
2k
1k
Frequency in Hertz
30˚
330˚
10 dB
5k
10k
Response in dB
20k
300˚
270˚
240˚
210˚
SCALE IS 5 DECIBELS PER DIVISION
60˚
90˚
120˚
LEGEND
200 Hz
150˚
180˚
1 kHz 5 kHz 8 kHz
Loading...