Audio Technica ATW-DA600, ATW-DA700 Installation And Operation Manual
Professional
UHF Wireless Systems
ATW-DA600
Diversity UHF Antenna Distribution System, 656-680 MHz
ATW-DA700
Diversity UHF Antenna Distribution System, 728-752 MHz
Installation and Operation
Front Panel Controls and Functions (Fig. A)
1. POWER SWITCH: Press switch On ( I ) to apply AC power to unit.
2. POWER INDICATOR: Shortly after power is applied, the indicator will light.
Figure A: ATW-DA600 front view
ATW-DA600 and ATW-DA700 Installation and Operation
AVIS
RISQUE DE CHOC
ÉLECTRIQUE
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
Caution/Avis:
Replace with same type 2.5A 250V fuse.
Utiliser un fusible de rechange de même type de
2.5A 250V.
2.5A 250V
To prevent electric shock, do not remove the cover. There are no
user-serviceable parts inside. Internal adjustments are for qualified
professionals only. Refer all servicing to qualified service personnel.
Pour prévenir un choc électrique, ne pas ouvrir le couvercle. Il n’y
aucune pièces de rechanges à l’intérieur. Tout ajustement interne
doit être fait par une personne qualifié seulement. Référez tout
réparation au personnel qualifié.
Warning/Attention:
To prevent fire or shock hazard, do not
expose this appliance to rain or moisture.
Pour prévenir feu ou choc électrique, ne pas
exposé l’appareil à la pluie ou à l’humidité.
Prior to use of this product, review all safety markings and instructions.
The ATW-DA600 is a UHF active unity-gain antenna
distribution system operating over the 656-680 MHz range.
The ATW-DA700 is identical in all respects to the ATW-DA600
except for its operating frequency range: 728-752 MHz.
The ATW-DA600 provides two identical sections, one for each
antenna of a UHF diversity wireless system. Each section
in the unit comprises an antenna input, four bandpassed,
isolated receiver outputs, and a bandpassed “cascade”
directional coupler to supply signal to additional ATW-DA600
units. All RF connectors are BNC-type. Ten BNC-to-BNC RF
interconnect cables are included with the unit.
Antennas can be remotely located from the unit. However,
due to signal loss in cables at UHF frequencies, use the
lowest-loss RF cable type(s) practical for any cable runs over
25 feet. RG-8 is a good choice. Use only copper-shielded
cable, not CATV-type foil-shielded wire.
Either passive or active antennas may be used. Both antenna
input jacks provide +12V DC output on their center pins to
operate Audio-Technica powered antennas or other in-line RF
devices, if desired. Up to 250 mA can be drawn from each
antenna input jack.
Additionally, four jacks on the rear panel provide 12V DC
(center
positive
) to power as many as four receivers operating
on 12 volts at 350 mA each. Included with the unit are four
polarity-inverting DC cables appropriate for use with ATW-R73
(or like-powered) receivers.
The 12-volt supplies for powering receivers and in-line devices
are short-circuit protected.
The unit’s switching power supply is designed to operate
properly from any AC power source 100-240V, 50/60 Hz
without adjustment. Simply connect to a standard AC power
outlet, using an IEC input cordset approved for the country of
use. The unit normally is supplied with a 120V cordset.
The unit includes pre-installed rack adapters (“rack-mount
ears”) for mounting in a standard 19" rack. (#10-32 rackmounting screws are not included.) If rack mounting is not
required, the adapters may be removed by simply taking out
the three screws holding each adapter in place. Save the
adapters and screws for possible future use.
1
2
Loading...