Audio-Technica ATM75 User Manual

ATM75

Cardioid Condenser Headworn Microphone

Features

• Ideal for drummers, keyboard players, guitarists or anyone requiring hands- free operation

• Low-visibilty headband provides stable, comfortable t

• Pivot-mounted exible mic boom descends from left or right side

• Belt-mounted power module operates on battery or phantom power

• Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source

• Rugged design and construction for reliable performance

• Switchable 80 Hz high-pass lter minimizes pickup of undesired low-frequency sounds

• Also available in two additional versions (without power module) ATM75cW—cable terminated for A-T UniPak® wireless systems ATM75c—unterminated cable

ATM75 Description

The ATM75 is a headworn condenser microphone with a cardioid polar pattern. It is designed for use by performing musicians and others who require professional-quality vocal pickup with hands-free operation.

The microphone requires 11V to 52V phantom power or a 1.5V AA battery for operation. A battery need not be in place for phantom power operation.

The microphone’s cardioid polar pattern provides a 120° angle of acceptance.

The microphone includes a 1.4 m (4.6') permanently attached miniature cable. Its free end connects to the provided AT8531 power module via a TA3F-type connector. The output of the power module is a 3-pin XLRMtype connector.

A 3-position switch in the power module permits choice of off, on/at response or on/low-roll-off (via integral 80 Hz high-pass lter). The roll-off position reduces the pickup of low-frequency ambient noise.

The microphone comes equipped with a power module, a cable clip, a large windscreen, a small windscreen and a battery.

ATM75cW Description

The microphone is also available in a wireless model, the ATM75cW. The ATM75cW includes a 1.4 m (55") permanently attached miniature cable terminated with a locking 4-pin connector for use with Audio-Technica UniPak® body-pack transmitters. No power module or battery is included (or required) with the ATM75cW. The ATM75cW dimensions, polar pattern, and included accessories are otherwise identical to those of the ATM75.

artist series live sound microphones

the ATM75c.

Operation and Maintenance

The ATM75 requires 11V to 52V phantom power or a 1.5V AA battery for operation. A battery need not be in place for phantom power operation.

To install the battery, remove the cap from the top of the power module. Insert a fresh 1.5V AA battery (“+” end toward the cap release button), then reassemble the power module. For longest battery life, the switch should remain off except when the microphone is in use. Alkaline batteries are recommended for longest life. Remove the battery during long-term storage.

Output is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive acoustic pressure produces positive voltage at Pin 2.

A 3-position switch in the power module permits choice of off, on/at response, or on/low-roll-off (via integral 80 Hz high-pass lter). The roll-off position reduces the pickup of low-frequency ambient noise (such as trafc, air-handling systems, etc.), room reverberation and mechanically coupled vibrations. To engage the high-pass lter, slide the switch toward the “bent” line. To turn the microphone on without engaging the highpass lter, slide the switch toward the at line.

For maximum stability and minimum visibility, the headband should be worn around the back of the head, with each cushioned support pad resting on the temple in front of the ear. The cable should remain clipped to the headband, with some slack at the boom connection. The headset is designed so the microphone descends from the left or right side.

After use in high-moisture applications, such as aerobics instruction, on-stage performing, etc., remove the foam screen, wipe off the headset with a towel and permit them to air-dry. (Do not store in a closed space, such as a plastic bag, until all moisture has evaporated.)

Avoid leaving the microphone in the open sun or in areas where temperatures exceed 110° F (43° C) for extended periods. Extremely high humidity should also be avoided.

Architect’s and Engineer’s Specications

The microphone shall be a xed-charge condenser designed for headworn use. It shall have a cardioid polar pattern with a uniform 120° angle of acceptance and a frequency response of 100 Hz to 13,000 Hz. The microphone shall operate from an external 11V to 52V DC phantom power source or, alternatively, from a 1.5V AA/UM3 battery. It shall be capable of handling sound input levels up to 132 dB (phantom) or 121 dB (battery) with a dynamic range of 96 dB (phantom) or 85 dB (battery). Nominal open-circuit output voltage shall be 2.8 mV (phantom) or 2.2 mV (battery) at 1 V, 1 Pascal. Output shall be low impedance balanced (200 ohms – phantom, 270 ohms – battery).

The microphone shall have a 1.4 m (4.6') permanently attached miniature cable, terminating in a TA3F-type output connector. The output connector shall connect to a TB3M-type jack on the included power module. The power module shall house the battery, and shall contain a switch that permits choice of off, on/at response or on/low-roll-off (80 Hz). The output of the power module shall be a 3-pin XLRM-type connector.

The microphone shall be a headworn design with an element diameter of 20.4 mm (0.80"). Weight shall be 60 grams (2.1 oz). The microphone shall include a power module, a cable clip, a large windscreen, a small windscreen and a battery.

The ATM75cW is also available with a 2.2 m (7.2') unterminated cable as

1.4 m (55") permanently attached miniature cable terminated with a locking 4-pin connector for use with Audio-Technica UniPak

body-pack transmitters. No power module or battery shall be required or included with the wireless model. The wireless model dimensions, polar pattern and included large windscreen shall be identical to those of the wired model. The wireless model shall also be available with a 2.2 m (7.2') unterminated cable.

The Audio-Technica ATM75 [ATM75cW-wireless]; [ATM75c-unterminated] is specied.

SpecicationsThe microphone shall also be available in a wireless model with a

Element

Polar pattern

Frequency response

Low frequency roll-off

Open circuit sensitivity

Impedance

Maximum input sound level

Dynamic range (typical)

Signal-to-noise ratio1

Phantom power requirements

Battery type

Battery current / life

Switch Weight

Dimensions

Output connector

Cable

Audio-Technica case style

Accessories furnished

In the inter est of standards devel opment, A.T.U.S.

offers full details on its test me thods to other industr y

1 Pascal = 1 0 dynes/cm

Typical, A-weighted, using Audio Precision System One.

Specication s are subject to chang e without notice.

professional s on request.

= 10 microb ars = 94 dB SPL

361

ATM75

Fixed-charge back plate, permanently polarized condenser Cardioid 100-13,000 Hz 80 Hz, 18 dB/octave Phantom: –51 dB (2.8 mV) re 1V at 1 Pa Battery: –53 dB (2.2 mV) re 1V at 1 Pa Phantom: 200 ohms Battery: 270 ohms Phantom: 132 dB SPL, 1 kHz at 1% T.H.D. Battery: 121 dB SPL, 1 kHz at 1% T.H.D. Phantom: 96 dB, 1 kHz at Max SPL Battery: 85 dB, 1 kHz at Max SPL 58 dB, 1 kHz at 1 Pa 11-52V DC, 2 mA typical

1.5V AA/UM3

0.4 mA / 2000 hours typical (alkaline) Off, on-at, on-roll-off Microphone: 60 g (2.1 oz) Power module: 139 g (4.9 oz) Microphone: 20.4 mm (0.80") diameter Power module: 84.0 mm (3.31") H x

63.0 mm (2.48") W x 22.0 mm (0.87") D Headset: 120.0 mm (4.72") nominal at widest point, 80.5 mm (3.17") exible boom Power module: Integral 3-pin XLRM-type

1.4 m (4.6') long (permanently attached to microphone), 2.8 mm (0.11") diameter, 2-conductor shielded cable with TA3Ftype connector M19 AT8531 power module; AT8439 cable clip; AT8139L large windscreen; AT8139S small windscreen; battery

frequency response: 100–13,000 Hz

10 dB

100

12" or more on axis Roll-off

330˚

200

Frequency in Hertz

0˚

180˚

500

30˚

150˚

60˚

120˚

10k

90˚

LEGEND

200 Hz

1 kHz 5 kHz 8 kHz

LEGEND

polar pattern

300˚

270˚

240˚

210˚

SCALE IS 5 DECIBELS PER DIVISION

Response in dB

20k