Audio-Technica AT-LP60X Users Manual
AT-LP60X
User Manual
Automatic Belt-Drive Turntable
Introduction
Thank you for purchasing this Audio-Technica product.
Read through this user manual before using the product to ensure its correct use. Also, keep this manual for future reference.
This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the plug of AC
adapter of the product are correct for the country you live in.
Package contents
Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Audio-Technica dealer.
•
Turntable body
•
45 RPM adapter
•
Felt mat
•
RCA audio cable
•
Platter (with drive belt)
•
AC adapter (approx. 1.5 m (4.9'))
•
Quick start guide
•
Caution guide
(approx. 1.2 m (3.9'))
After purchase, we suggest that you save all packaging materials for possible future storage, moving, or shipping.
1
Safety precautions
Safety precautions
Although this product was designed to be used safely, failing
to use it correctly may result in an accident. To ensure safety,
observe all warnings and cautions while using the product.
Important information
Warning:
To prevent fire or shock hazard, do not expose this apparatus
to rain or moisture.
Caution:
•
Do not expose this apparatus to drips or splashes.
•
To avoid electric shock, do not open the cabinet.
•
Refer servicing to qualified personnel only.
•
Do not expose this apparatus to excessive heat such as
sunshine, fire or the like.
•
Do not subject this apparatus to strong impact.
•
This apparatus should be located close enough to the AC
outlet so that you can easily grasp the AC adapter at any time.
•
In case of emergency, disconnect the AC adapter quickly.
•
Do not place any objects filled with liquids, such as vases, on
this apparatus.
•
To prevent fire, do not place any naked flame sources (such
as lighted candles) on this apparatus.
•
Do not install this apparatus in a confined space such as a
bookcase or similar unit.
•
Install this apparatus only in the place where ventilation is good.
•
The rating label is put on the bottom of this apparatus.
For customers in the USA
For customers in Canada
IC statement:
CAN ICES-3 (B)/NMB-3(B)
Notes on use
Turntable body
•
Do not set and use the product in locations that are
considerably hot or humid, dirty, or subject to extreme
vibrations.
•
The product should be positioned on a flat, level surface.
•
When closing the dust cover, close it completely. Do not open
the dust cover during playback.
Cartridge
•
Attach the provided protector to the cartridge when the
product is not in use.
•
Do not touch the stylus of the cartridge with your finger.
•
Do not allow the stylus to bump against the platter, felt mat,
or edge of the record.
FCC Notice
Warning:
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
Caution:
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
2
Part names and functions
10
5
1
2
3
4
5
6
7
8
9
11 12 1513 1614 17
45 RPM adapter (shown in receptacle)
1
Adapts 7" records with large center holes to fit center
spindle.
Platter
2
Spindle
3
Felt mat
4
Dust cover hinge holders
5
Attachment points for dust cover hinges.
Tonearm
6
Tonearm rest
7
Headshell and cartridge
8
The cartridge (AT3600L) is attached to the headshell.
Size selector
9
Switch between 12" and 7", according to the size of the
record.
Dust cover
10
Platter speed button
11
Select the platter speed (33-1/3 or 45 RPM).
START button
12
Spins the platter and moves the tonearm.
STOP button
13
Returns the tonearm to its original position and stops the
platter.
Tonearm lift button
14
Lifts and lowers tonearm for manual selection.
Pre-amplifier selector switch
15
If using an amplifier with a PHONO input jack, set this
switch to the PHONO position. If connecting to the AUX
jack of an amplifier, set this switch to the LINE position.
Stereo output terminals
16
Connect the RCA audio cable.
Power input jack
17
Connect the AC adapter.
3
Loading...