Page 1
Page 2
Contents
Model DSi200
Section Page No.
Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1
Description of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1, 2
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disposal and Recycling Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Page 3
Model DSi200
INTEGRA TED AM PLI FIER
DS I2 00 HIG H DEF INITI ON
®
POWER MONO INVERT MUTE
D I S P L A Y
MODEL DSI200
INTEGRATED AMPLIFIER
PLYMOUTH, MINNESOTA
MADE IN U.S.A.
MAX POWER CONSUMPTION
815 W
50/60 HZ
˜
SERIAL
VOLTS
6A FUSE SLO-BLO
(T3.15A 230V)
CAUTION
FOR PROTECTION AGAINST
FIRE HAZARD, REPLACE
ONLY WITH SAME RATING FUSES.
BAL 1
TUNER
AUX
BAL 2 CD
INVERT POWER
MUTE VOL DN VOL UP
BAL L BAL R
DSP DN
DSP UP
MONO
PROC
l
n
VOLUME INPUT
D E F I N I T I O N S E R I E S
+ -
RIGHT
OUTPUT
- +
LEFT
OUTPUT
WARNING!
RISK OF HAZARDOUS ENERGY!
MAKE PROPER SPEAKER
CONNECTIONS
SEE OWNERS MANUAL
WARNING!
RISK OF HAZARDOUS ENERGY!
MAKE PROPER SPEAKER
CONNECTIONS
SEE OWNERS MANUAL
BAL 1 BAL 2 BAL 2 BAL 1CD TUNER AUX/PROC
AUX/PROC TUNER CD
RIGHT INPUTS
LEFT INPUTS
D S i 2 0 0
Page 4
Model DSi200
1
Preface
Please take time to carefully read and understand the following instructions before you install or attempt to operate
your Audio Research DSi200 integrated preamplifier.
Becoming familiar with the product and its correct operating procedures will help assure you of maximum musical
enjoyment and reliable operation. The effort you invest
now will be well rewarded in the years ahead.
Warnings
1. To prevent fire or shock hazard, do not expose this
product to rain or moisture.
2. This unit operates on voltages which can cause serious
injury or death. Do not operate with covers removed.
Any necessary servicing should be carried out by your
authorized Audio Research dealer or other qualified
electronics technician.
3. The 14- gauge power cord supplied with this unit is
safety-tested and is equipped with a proper grounding
plug. If used normally, it will provide a safe earth ground
connection of the chassis. Defeat of the grounding plug
or use of a power cord without a grounding plug, or any
unauthorized modification of the active circuitry or
controls of this unit, automatically voids warranty coverage, and could cause injury or death.
4. For safe operation and protection against fire hazard,
replace fuses only with those of the same type and
rating as those supplied with this unit.
Packaging
Save all packaging accompanying this product. You have
purchased a precision electronic instrument, and it should
be properly cartoned any time shipment becomes necessary. It is very possible that this unit could be damaged
during shipment if repackaged in cartoning other than that
designed for it. The original packaging materials help protect your investment from unnecessary damage, delay and
added expense whenever shipment of this unit is required.
Accessories
Spare Fuses:
2 – 6 Amp MDQ slo-blo (100 & 120v)
2 – T 3.15A Super-Time-Lag TT (220 -240V)
Description of Controls
F ront Panel Rotary Contro l s :
The DSi200 has two microprocessor-driven rotary
controls.
Vo l u m e
The rotary control on the left adjusts Volume (output level)
up or down for both R and L channels. Volume control is
also selectable via Vol DN and Vol UP buttons on the
remote control. Volume adjustment is indicated in the
display window by numeric digits on 0–103 scale.
Do not turn volume up beyond normal listening levels
when “mute” is engaged to avoid unexpected or possibly
damaging sound levels. Reduce volume level whenever
changing input sources, even when muted.
Input
The rotary control on the right selects any of 5 input
sources connected to the DSi200: Bal 1, Bal 2, CD, Tuner
and Aux. Each of these sources may also be selected via
di r ect acc ess buttons on the remote co n t r o l . The
selected source is indicated in the display window.
F ront Panel and Remote Control Buttons
POWER ON/OFF: Supplies power from A.C. wall outlet to
DSi200; indicated by active display window. Function
also on remote control.
Fo r approxi m ately 5 second s after start up, “ Mute”
appears in the display window and flashes until the automatic muting cycle is completed. This also occurs in the
event of power interruption. Upon completing the cycle,
“Mute” will cease flashing. The DSi200 will remain muted
until normal operation is selected by pressing the “Mute”
button.
MUTE: When activated, electrically mutes all output of the
DSi200; indicated by “Mute” in display window. This control should be activated before switching inputs, changing
connections or shutting down your audio system to help
protect your speakers from unexpected signal pulses.
When deactivated, “Mute” disappears from the display window allowing normal operation. Function also on remote
control.
The DSi200 also has automatic muting to help protect system components during A.C. power interruption s or low
line voltage. When sensing these conditions, the unit
automatically goes into “Mute” and disables all outputs.
The 5-second warm-up timer will restart and “Mute” will
flash in the display window when normal power conditions have been restored.
Note that automatic muting is only designed to protect
against power line interruptions or severe voltage drop. It
will not mute in the event of subsonic transmissions from
a faulty input source or speaker malfunction.
Page 5
PROCESSOR (PROC): The Aux/Proc input may be used as a
normal input for a line-level source, or it may be used as a
fixed level pass-through for use with a home theater
processor. When the Processor button on the remote control is engaged, “PROCESSOR” will appear on the display,
the volume will not be adjustable, and the gain will be
fixed at 26dB (typical of a separate amplifier). Fixing the
gain will allow the home theater processor (connected to
Aux/Proc) to control the overall volume of the complete
multichannel system, including the DSi200.
WARNING: Before unmuting the “PROC” input, be sure
to turn the volume down on the home-theater processor.
Never connect a line-level source (DVD player, tuner,
CD, etc.) and then select “PROC” input on the remote or
the speaker system could be damaged when the DSi200
is unmuted.
INVERT: Inverts absolute phase of output signal. Remem-
bers setting for each input independently. “Invert” disabled
in Processor mode.
VOLUME UP/ D O W N : Increases/decreases overall volume
level of both channels equally for whichever input has been
selected. Caution: do not turn up volume beyond normal
listening levels when “Mute” is engaged to avoid unexpected or possibly damaging sound levels. It is a good idea to
reduce volume whenever changing program sources, even
when muted. Function available on remote control buttons
and front panel rotary control on left.
M O N O : Sums L and R input for mono output from any
source selected. Remembers setting for each input independently. “Mono” disabled in Processor mode.
Remote Control-Only Functions
DISPLAY DOWN/DISPLAY UP [DSP DN/DSP UP]: Decreas-
es/increases display intensity, offering six levels of brightness and display “off”. If display “off” is selected, a small
segment of pixels remains illuminated in the center of the
display window as a reminder the unit is turned on. In
display “off ” mode the displa y will illuminate for 10
seconds when any button (except Power on/off) is selected,
allowing for control function navigation.
BALANCE (BAL L / B A L R ) : Adjusts balance left or right
Adjustment appears in display window as movable marker
on bar graph. Useful for compensating for uneven speaker
placement or imbalanced output from a phono cartridge
or other source. Remembers setting for each input independently. “Balance” disabled in Processor mode.
Connections
The Rear Panel has:
2 – Sets of BAL input connectors (BAL 1, BAL 2)
3 – Sets of SE input connectors (CD, TUNER, AUX/PROC)
4 – Output binding posts (+) and (-), L & R
1 – Power line cord 15A IEC connector for removable
power cord (supplied)
1 – Power line fuseholder
IMPORTANT: Use the best available speaker wires and interconnects. As your system improves in resolution from
the addition of quality components, it becomes increasingly
important to avoid the limitations of inferior system interconnections.
It is important sonically that your entire system be connected so that the audio signal arriving at the speakers has
correct absolute polarity or phase (i.e. is
n o t
i n v e r t e d ) .
Connect the black or (-) speaker terminal to the wire that
connects to the appropriate-channel (-) gold binding post
on the DSi200. Connect the red or (+) speaker terminal to
the wire that connects to the appropriate-channel (+) binding post on the DSi200. Tighten the binding posts firmly to
assure good contact for best sonic results.
For “ b i - w i r ed” loudspeaker systems (i.e. running separate
wires to bass and treble speaker terminals), simply repeat
the above instructions, taking care that all connections
have the same (+) or (-) polarity.
Connect the DSi200 to source components, using only the
highest grade of audio interconnect cables. To avoid sonic
de gr a da tion use the s h o r t e s t pr ac tical length of
cables.
A.C. POWER CONNECTIONS: It is important that the
DSi200 be connected via its supplied 15 amp IEC 14-gauge
power cord to a secure, dedicated A.C. power receptacle.
Never connect to convenience power receptacles on other
equipment. Best results are usually achieved by plugging
the DSi200 directly into wall outlets.
The AC power source for the DSi200 amplifier should be
capable of supplying 6 amperes for 100 or 120 volt units,
or 3 amperes for 220 or 240 volt units.
For the very best performance on domestic 100 or 120 volt
circuits, the DSi200 should be connected to its own AC
power circuit branch, protected by a 15 amp breaker. The
other audio equipment should be connected to a different
power circuit and breaker.
The DSi200 uses a grounding system that does not require
a ground-lifter adaptor plug on the A. C. power cord to minimize hum. The pow e r co r d supplied with the
DSi200 has a standard grounding plug to provide maximum safety when properly connected to a grounded wall
receptacle. If there is any question regarding proper grounding procedures in your installation, seek help from a qualified technician. Caution should be taken before using
custom after-market power cords: they must be at least
Model DSi200
2
Page 6
14-gauge and have a standard grounding plug properly
installed. These power cords are to be used with caution,
at the sole risk of the owner.
Installation
The amplifier may be installed in a ventilated cabinet;
observe the following guidelines to maximize the performance and service of your amplifier.
With proper installation, the DSi200 may be left on continuously for maximum performance on demand; it will draw
38 watts of AC power at idle. However, the DSi200 has
been designed and engineered to minimize any “warm up”
necessary for best sonics; generally, a half-hour to 45 minutes of actual playing time will bring the amplifier around
to more than acceptable performance levels, with some
additional improvement noticeable over the next hour or
two. Warm-up characteristics will depend upon ambient
room temperature at start-up, the nature of the installation
and the resolving power of the associated equipment.
Operate the DSi200 only in a horizontal (upright) position.
Adequate airflow and proper cooling can be maintained
only if there is no restriction around the unit.
The five (5) non-marring feet provide adequate spacing and
mechanical damping only from a smooth, hard surface.
Never operate the unit while it is sitting on a soft, irregu lar surface such as a rug or carpet.
If the unit is to be operated in an enclosure such as an
equipment rack, make certain that adequate air flow above
and below the unit is provided. The “ambient” operating
temperature should never exceed 120º F or 49º C. Improper
installation will cause premature component failure and
will affect your warranty, as well as the service life of
the unit.
It is normal for the DSi200 power amplifier to run slightly
warm to the touch. All components within are operated at
safe, conservative levels and will not be improperly affected, providing the requirements outlined above are adhered
to.
Do not operate your DSi200 without the top and bottom
covers installed. These are required both for safety as well
as shielding from interference (except in service operations
by qualified personnel).
Operating Procedure
Start-up:
1. Ma k e sure you h av e read a nd c o m plied with t h e
INSTALLATION AND CONNECTION instructions prior
to attempting operation.
2. Secure all rear-panel connections between DSi200, and
input sources, and loudspeakers.
3. Make sure the DSi200 is properly connected to a ground-
ed high-curr ent power rec eptacle via the supplied
14-gauge, 3-prong grounded power cord (see AC POWER
CONNECTIONS).
4. Turn on source component(s) to be used.
5. Press Power switch (either on remote or front panel).
The display will illuminate and the Mute LED will flash
for approximately 5 seconds while power supply stabilizes, indicating operation of automatic muting circuit.
After this automatic muting period the word “MUTE”
will stay on, indicating that your DSi200 is in the “mute”
position. Adjust the Volume control to the minimum
level. Press
“Mute” button to initiate operation.
When
the “o p e r a t e” position is manually selected the word
“MUTE” will turn off, indicating the DSi200 is ready for
operation.
Note: If the display does not come on, check the line fuse
for possible failure. An extra fuse for A. C. power is
included with your DSi200.
6. Press Input selector for desired source; set remaining
switch options to desired positions.
7. Activate selected input source, then deactivate Mute
switch and adjust Volume control as necessary.
8. Your DSi200 should now operate satisfactorily. However,
a full stabilization or warm-up time of approximately one
half hour is recommended for best sonic performance.
Shut-Down:
1. Activate “Mute” function.
2. Set Volume level to “0”.
3. Press Power switch to “off ”.
4. Turn off input sources.
Troubleshooting:
It is possible for a static discharge to temporarily disable
the microprocessor that allows the controls to function. If
this should occur, depress the “Mute” button, then turn off
the DSi200 and
unplug from the A.C. receptacle for 60
s e c o n d s .
Reconnect the A.C. plug and turn the unit back
on. The controls should resume normal operation. If the
problem persists, contact your dealer or Audio Research
Customer Service at 763-577-9700.
Model DSi200
3
Page 7
Servicing
Because of its careful design and exacting standards
of manufacture, your DSi200 should require no routine
maintenance. The remote control's batteries (AAA) should
be replaced once a year.
CAUTION: Your DSi200 contains sufficient levels of voltage
and current to be lethal. Do n ot t a m p er wi t h a
component or part inside the unit. Refer any needed
service to your authorized Audio Research dealer or other
qualified technician.
Should ser v i c e b e ne ce s s ary, please contact your
Audio Research dealer, or Audio Research Customer Service
at 763 577-9700.
Cleaning
To maintain the new appearance of this unit, occasionally
wipe the front panel and top cover with a soft, damp (not
wet) cloth to remove dust. A mild, non-alkaline soap solution may b e used to remo v e fingerp rints or s imilar
smudges. Cleaners containing abrasives should
not
be used
as they will damage the anodized finish of the front panel.
A small, soft paint brush is effective in removing dust from
bevels, the recessed nameplate and other features of the
front panel.
Disposal and Recycling Guidelines
To dispose of this electronic product, do not place in landfill. In accordance with the European Union Waste Electrical and Electronic Equipment (WEEE) directive effective
August 2005, this product may contain regulated materials
which upon disposal require special reuse and recycling
processing.
Please contact your dealer or importing distributor for
instructions on proper disposal of this product in your
country. Or, contact Audio Research Corporation (763-577-
9700) for the name of your importing distributor and how
to contact them.
Packing and shipping materials may be disposed of in a
normal manner.
Limited Warranty
Audio Research Corporation products are covered by a 3Year Limited Warranty, or a 90-Day Limited Warranty
(vacuum tubes). This Limited Warranty initiates from the
date of purchase, and is limited to the original purchaser, or
in the case of demonstration equipment, limited to the
balance of warranty remaining after original shipment to
the retailer or importer.
In the United States, the specific terms, conditions and
remedies for fulfillment of this Limited Warranty are listed
on the warranty card accompanying the product in its
shipping carton, or may be obtained from the authorized
retailer or from the Audio Research Customer Service
Department. Outside the United States, the authorized
importing retailer or distributor has accepted the responsibility for warranty of Audio Research products sold by
them. The specific terms and remedies for fulfillment of
the Limited Warranty may vary from country to country.
Warranty service should normally be obtained from the
importing retailer or distributor from whom the product
was purchased.
In the unlikely event that technical service beyond the ability of the importer is required, Audio Research will fulfill
the terms and conditions of the Limited Warranty. Such
product must be returned at the purchaser's expense to the
Audio Research factory, along with a photocopy of the
dated purchase receipt for the product, a written description of the problem(s) encountered, and any information
necessary for return shipment. The cost of return shipment
is the responsibility of the purchaser.
Model DSi200
4
Page 8
Specifications
POWER OUTPUT: 200 watts per channel into 8 ohms,
1% THD; 300 watts per channel into 4 ohms, both channels
driven.
FREQUENCY RESPONSE: (-3dB points at 1 watt) 5Hz to
55 kHz.
INPUT SENSITIVITY: 0.93V RMS for rated output (32.7dB
Gain) single-ended or balanced.
INPUT IMPEDANCE: 60K ohms single-ended, 120K ohms
balanced differential.
INPUTS: (5): BAL1, BAL 2, CD(SE), Tuner (SE), Aux (SE).
MAXIMUM INPUT: 20V RMS BALANCED, 10V RMS SE.
OUPUT POLARITY: Non-inverting from single- ended inputs.
Balanced pin 2+ (IEC-268).
OUTPUT REGULATION: 0.06dB 8 ohm load to open circuit
(Damping factor 167).
OUTPUT CURRENT: 15 amps peak at protective shutdown.
SLEW RATE: 5 volts/microsecond. (20% maximum duty
cycle).
RISE TIME: 5.0 microseconds.
HUM & NOISE: 800 microvolts RMS (94dB below rated
output IHF A-weighted).
CONTROLS: Volume (104 steps), Select Input.
Push Buttons: Power, Invert, Mono, Mute.
POWER SUPPLY CAPACITANCE: 160,000 uF total.
POWER REQUIREMENTS: 100-125VAC 60Hz (200-250VAC
50Hz) 445 watts at rated output (200WPC 8 ohms), 735 watts
at 300WPC 4 ohms, 38 watts idle, Standby 1 watt.
DIMENSIONS: 19" (48 cm) W (standard rack panel) x 51/4"
(13.3 cm) H x 141/4" (36.2 cm) D (front panel back). Optional
handles extend 11/2" (3.8 cm) forward of the 1/4" thick front
panel. Output connectors extend 0.9" behind rear panel.
WEIGHT: 37.2 lbs. (16.9 kg) Net; 43.3 lbs. (19.7 kg) Shipping.
Specifications subject to change without notice.
©2009 Audio Research Corporation.
5
Model DSi200
Loading...