Page 1
9000CDT
SELECT
User Manual
Page 2
Important
Safety Information
1: Important Safety Information
This lightning flash with an arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of non-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.
Warning: To reduce the risk of electric shock, do not remove the cover (or back) as
there are no user-serviceable parts inside. Refer servicing to qualified personnel.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance instructions in the literature
accompanying the appliance.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install under the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding plug has
two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for the replacement of the obsolete outlet.
Protect the power cord from being stepped on or pinched, particularly at the plugs,
convenience receptacles, and at the point where they exit from the apparatus.
Unplug this apparatus during lightning storms or when unused for long periods.
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power supply cord or plug is
damaged, liquid has been spilt or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock, do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
Do not install this equipment in a confined or built-in space such as a bookcase or
similar unit, and keep well ventilated in an open space. The ventilation should not
be impeded by covering the ventilation openings with items such as newspaper,
tablecloths, curtains etc.
WARNING: Only use attachments/accessories specified or provided by the
manufacturer (such as the exclusive supply adapter, battery etc).
WARNING: Please refer to the information on the exterior panel of the enclosure
for electrical and safety information before installing or operating the apparatus.
WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. The apparatus shall not be exposed to dripping or
splashing and objects filled with liquids, such as vases, shall not be placed on the
apparatus.
WARNING: For the terminals marked with the symbol “ ” may be of sufficient
magnitude to constitute a risk of electric shock. The external wiring connected to
the terminals requires installation by an instructed person or the use of
ready-made leads or cords.
Denmark:
Finland:
Norway:
Sweden:
WARNING: No naked flame sources, such as lighted candles, should be placed on
the apparatus.
WARNING: Attention should be drawn to the environmental aspects of battery
disposal.
WARNING: Use of the apparatus in tropical climates.
THE FUSE VALUES ARE:
220 – 240V (UK, China, etc.) T630mAL 250V Slow Blow
100 – 120V (USA, Japan, etc.) T1.0AL 250V Slow Blow
System Operations
Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver
forbindelse til stikproppens jord.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan.
Apparatet må tilkoples jordet stikkontakt.
Apparaten skall anslutas till jordat uttag.
This label tells you that the unit contains a laser component.
Opening the unit will expose the user to radiation from the laser.
The apparatus with CLASS I construction shall be connected to a
mains socket outlet with a protective earthing connection.
Playing Operations
Warranty Coverage
Specifications
Page 3
Important
Safety Information
1: Important Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
•
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
Caution: Any changes or modifications to this device not explicitly approved by the
manufacturer could void your authority to operate this equipment. This device
complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operation.
ISED Statement
This device contains license-exempt transmitter (s) / receiver (s) that comply with
Innovation, Science and Economic Development Canada's licence-exempt RSS (s).
Operation is subject to the following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interference that may cause
undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B) / NMB-3 (B).
This device meets the exemption from the routine evaluation limits in section 2.5
of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment.
The device has been evaluated to meet general RF exposure requirements.
RF Exposure Information
•
The device has been evaluated to meet general RF exposure requirements.
•
The device can be used in portable exposure condition and compliance with
exposure requirements.
Page 4
Important
Safety Information
2: Contents
Audiolab 9000CDT
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
Getting Started ....................................................................................................................................................................................................
Controls and Functions ....................................................................................................................................................................................
Remote Handset ................................................................................................................................................................................................
Connections .........................................................................................................................................................................................................
....................................................................................................................................................................................................
Menu Options
System Operations ........................................................................................................................................................................................... 11
Playing Operations ...........................................................................................................................................................................................
Warranty Coverage ............................................................................................................................................................................................
Specifications ....................................................................................................................................................................................................
13
14
16
5
6
7
8
9
Page 5
Important
Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
3: Getting Started
Introduction of 9000CDT
Audiolab’s new 9000 Series represents a new standard in home audio for the
connoissuer.
The 9000CDT is a dedicated CD transport that incorporates a high-end mechanism
developed to suit the industry benchmarks set by Audiolab performance
philosophies.
Following in a long list of award-winning Audiolab CD playback devices, the
9000CDT uses a high-precision optical system with an electronic data buffer for
accurate and seamless CD playback, with a read-ahead digital buffer to reduce
disc-reading failures, the 9000CDT offers the ability to play scratched and
damaged CDs that are unreadable by conventional mechanisms.
Features
• High-end CD mechanism with a precision optical system
• Playback from CD or USB HDD
• Automatic equipment activation via 12V trigger input
• 800 x 480mm WVGA full view IPS LCD screen
Inputs
• CD disc playback
• USB storage device
Outputs
• One coaxial output
• One optical output
Page 5
Unpacking the Equipment
The carton should contain:
• The Audiolab 9000CDT
• One IEC power cord suitable for your area
• One remote handset
• One instruction manual
Please note: The remote control requires 2 x AAA type batteries. Due to
international shipping and courier regulations with Lithium-Ion batteries, the
remote controller batteries are not included in this package.
Consult the dealer from whom you purchased the equipment if any item is not
present. Carefully unpack the unit and accessories. Take care not to damage the
surface finish when undoing the protective polythene sleeve. Retain the packing
materials for future use. Retain the user manual and information concerning the
date and place of purchase of your equipment for future reference. If you transfer
the unit to a third party, please pass on this instruction manual along with the
equipment.
Placement
The unit must be mounted on a solid, level and stable surface.
Before you connect the Audiolab 9000CDT to the AC mains power, ensure your AC
mains voltage corresponds to the rating on the rear panel of the product. If in
doubt, consult your dealer. If you move to an area that has a different mains
voltage, seek advice from an Audiolab appointed dealer or a competent service
technician.
Page 6
Important
Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
4: Controls and Functions
CD Tray Eject / Load CD Tray
Display
Power Switch
Page 6
Power LED
SELECT
Control / Source Select Standby Button
POWER
ON OFF
AC220-240V~50/60Hz 22W
FUSE T630mAL 250V
Mains Input
CLASS 1
LASER PRODUCT
9000CDT
Made in China
HUNTINGDON, UNITED KINGDOM
12V
TRIG
IN
62638-1
NO. 62638-1
3021177
12V
Triggers
LINK
(5V 1A)
USB HDD
Input / Update
DIGITAL
OPT COAX
OUTPUT
Optical / Coaxial
Output
WWW.AUDIOLAB.CO.UK
CD Player MODEL: 9000CDT
Page 7
Important
Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
5: Remote Handset
2. PROG
9
1
2
4
5
6
7
8
SOURCE TIME DISPLAY BAC K
CD A
RANDOM
MODE LIST MENU
DEVICE
N
10
113
12
13
14
15
16
17
18
19
20
21
3. REPEAT
4.
5.
6.
7. SOURCE
8. TIME
9. STANDBY
10. STORE
11. RANDOM
12. VOL+
13.
14.
15. VOL-
16.
17.
18. LIST
19. MENU
20. BACK
21. CD/A/N
Press to go directly to a track by number1. NUMBER KEYS
Press to program tracks of your choice
Press to select the repeat mode
Move to the previous track
Press to stop
Press to eject / load the disc
Press to cycle source inputs
Press to toggle single track time remaining
or all tracks time remaining
Press to bring the unit in / out of standby
Press to store a track in program mode
Press to select random mode
Move to the previous option in menu settings
Move to the next track
Press to start / pause. Press to confirm setting
selected in menu
Move to the next option in menu settings
Press and hold to fast reverse
Press and hold to fast forward
Press to enter playlist
Press to enter menu mode
Press to go back when navigating directories
(Menu, USB, etc.)
Press to select the model - 9000CDT/9000A/9000N
Page 7
Fit the Batteries
Open the cover and insert 2 x AAA batteries (not
supplied), replace the cover.
Always use AAA batteries and replace them in sets –
never mix up old and new batteries. Very weak
batteries can leak and damage the handset. Replace
them in good time!
Note: there is a risk of fire and injury if a battery is
handled improperly. Do not disassemble, crush,
puncture, short the contacts or dispose of the
batteries in fire or water. Do not attempt to open or
service a battery. Discard used batteries in full
accordance with recycling regulations in force in your
area.
Handset Operation
Point the handset at the remote receiver and press
the buttons as illustrated to activate the relevant
functions.
The handset should be within 15 meters of the player
and there should be a clear line of sight between the
handset and unit for optimum remote control
operation.
Note: The handset can also operate other units in the
Audiolab 9000 series. The buttons shown crossed out
are for use with other Audiolab units.
Page 8
Important
Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
6: Connections
USB Update
Follow the instructions provided separately with the official
Audiolab USB update files.
POWER OFF the 9000CDT unit. Insert the USB storage device, onto
which the USB update files have been loaded. Press the 'STANDBY'
button on the front panel then simultaneously POWER ON, your
9000CDT will upgrade automatically. Wait for the device display to
confirm that the update is completed. Then, unplug the USB drive
and restart the 9000CDT. The unit is now ready to use.
12V Trigger Connection
The 9000CDT features two 12V trigger connections on the rear
panel. One is an input from your amplifier, and the other is a link
that can be used as an output to connect to other products such as
the wider 9000 series models. For the Audiolab 9000 series, this will
be a 3.5mm to 3.5mm interconnect.
12V
TRIG
LINK
Page 8
Coaxial and Optical Output
The 9000CDT offers one Coaxial and one Optical SPDIF digital
output. Connect a suitable Digital Coaxial (fully screened)
interconnect or Optical cable from the appropriate SPDIF
output of the 9000CDT to the input of a DAC or digital input
on your chosen amplifier or preamplifier.
Mains Input
IN
Before connecting the AC power cord to the 9000CDT, please
make sure the Power Switch is in the OFF position. Switch it
to the ON position after connecting the unit to the AC mains.
DIGITAL
OPT COAX
OUTPUT
AC220-240V~50/60Hz 22W
FUSE T630mAL 250V
Page 9
Important
Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
7: Menu Options
Auto Source Select
This option enables or disables the 9000CDT's
automatic detection of a CD or USB device
when in playback mode.
With auto input select 'ON’ the 9000CDT will
offer the user the immediate option to
change input source, when a CD or USB
device is detected. If the option is not
activated within 5 seconds, the device will
continue to play as normal from current
source.
Display Option
Access the various display options for the
9000CDT front panel display.
Page 9
Display Time Out
Adjust the time period after which
the 9000CDT display will revert to
your pre-chosen display option, after
performing track select, volume
adjust and other operations.
Animation
Activate (ON) or deactivate (OFF) the
animations shown in the of the
playback interface display.
Brightness
Adjust the brightness of the 9000CDT front
panel display.
Trigger
Activate or deactivate the 12V
trigger function of the 9000CDT.
Page 10
Important
Safety Information
Contents Getting Started Controls and Functions
Remote Handset
Connections Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
7: Menu Options
Language
The 9000CDT offers multiple language
options for the GUI. Select your chosen
language from the list. The default language
is ‘English’.
Standby
The auto-standby feature will put the
9000CDT into standby mode after 20
minutes of inactivity. This feature can be also
user defined and set to 20 minutes, 60
minutes or ‘never’.
Page 10
Version
Check the current operational
firmware version.
Settings / Standby
Never
20 minutes
60 minutes
The latter option meaning that the 9000CDT
will not enter standby mode without user
instruction by way of the front panel
‘standby’ button or remote control ‘standby’
button.
Reset
Reset the 9000CDT to the factory default
settings.
Page 11
Important
Safety Information
Contents Getting Started
Controls and Functions Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
8: System Operations
Switching On and Off
The 9000CDT should be switched on before the amplification stage in your system.
When switching off your system, turn off the amplifier stage before switching off the
9000CDT.
Standby Mode
After initial power is on, the 9000CDT will be in ‘standby’ mode.
To use the 9000CDT, press the 'STANDBY' button to bring the 9000CDT out of
standby.
The power indicator LED will become brighter and the display will show the
'Audiolab' welcome screen as the unit enters the operational mode.
Source Select
or ▼ buttons on the remote handset to select the different source options.
Page 11
Alternative Display Options
The Audiolab 9000CDT has an intelligent and versatile display. You can access the
display options via the menu function.
Press the 'MENU' button on the remote controller to enter menu mode, or
long-press the 'SOURCE' button on the front panel of the device.
A 2 seconds press of the front panel source button brings up the option to change
input source. Continue pressing for a total of 5 seconds to bring up the menu.
Navigate to 'Display Options' via the menu options (use the VO
remote or front panel of the device for navigation. You can also use the and
buttons to navigate.)
Choose and confirm by on the remote control or front panel of the device.
Long press the ‘SELECT’ knob on the front panel for 3 seconds or use the source ▲
L+/- buttons on the
Auto Source Select
When the 'Auto Source Select’ option is active, insert a USB drive when playing CD,
or load a CD when playing from USB HDD and the 9000CDT will automatically offer
out a source select option.
You can immediately select the alternative source by press on the remote
controller. If this is not required, 9000CDT will remain on the current playback
source if no confirmation is made within 5 seconds.
Home
Display Off
Audiolab
Page 12
Important
Safety Information
Contents Getting Started
Controls and Functions Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
8: System Operations
Page 12
The Menu
The menu enables you to customize the unit and optimise the interface with other equipment in your system.
Press the ‘SELECT’ knob on front panel or ‘MENU’ key on the remote controller to enter menu mode, and then press 'VOL-' or 'VOL+' to cycle through the menu options.
Press to access the sub menus and press again to confirm any selection.
You can also press the 'SELECT’ button on the front panel to enter the menu, then rotate it cycle menu options. Press ‘SELECT’ again to enter the sub menu. And, press ‘SELECT’
again to confirm any selection.
The Menu Tree
Auto Source Select
Off
On
Wide
Display Option
Audiolab
Display Settings
BrightnessHome
Trigger Language
1
10
On
Off
10s
Standby
NeverEnglish
20min
Reset Version
No
Yes
VER-1.001
COAX2 DPLL
Norm
Wide
Display Off
Display time out
Animation
10s
15s
30s
On
Off
5s
15s
30s
60min
Page 13
Important
Safety Information
Contents Getting Started
Controls and Functions Remote Handset
Connections
Menu Options
System Operations Playing Operations
Warranty Coverage
Specifications
9: Playing Operations
CD Playback
Press the on the remote controller or front panel to load/eject the disc.
Press the to play the CD. Press the button again to pause CD playback.
Press to stop playing the CD, and then press to eject the disc.
Previous/Next track: skip back to the start of current track by pressing button
once. Skip back to previous track by pressing button twice. Skip forward to next
track by pressing button once.
Press and hold / to fast reverse/fast forward search.
Direct Selection of Tracks via the Remote Control
Select the desired track directly from the remote keypad by using the numerical
buttons. The 9000CDT will automatically skip to the track number corresponding to
the number keypad.
If you choose a single digital track (e.g.1) in a disc which contains more than 10
tracks, the player will pause briefly, waiting for you to enter a second digit. If none
is entered, player will commence from the entered single-digit track. If the choice is
invalid the display reverts to the previous state and playback / operation will
continue.
Repeat Play
Press the ‘REPEAT’ button on the handset once to repeat a single track. Press it
again to repeat all of the tracks on the disc / folder. The or on the display
will turn red if or is activated.
1
1
Page 13
Once you have populated your tracklist, scroll left and right using the and
buttons on the remote control to select which track you would like to start playing
from. For example, to play from the beginning of your programmed list, scroll left to
the first stored track.
Begin playback by pressing the button. Playback of your programmed list will
start, beginning with the currently selected track. Press the button to stop
programmed playback.
To exit the ‘Programme’ playback mode, press the button twice.
Playback from USB HDD Storage Device
The 9000CDT can play music files saved on a USB HDD storage device and is
compatible with USB devices that are 'FAT12', 'FAT16' and 'FAT32' formatted.
The 9000CDT supports audio files in the format of WMA, MP3, WAV and AAC.
Connect your USB device to the rear panel USB port. Select USB HDD
playback input.
Play/Pause by pressing the button on the remote control or front
panel.
You can use the buttons on the remote control to skip, fast forward and fast
reverse tracks as you would with CDs.
Compatible Formats
(5V 1A)
Random Play
Press the ‘RANDOM’ button on the remote controller to activate random playback
mode. The ' ' icon on the display will turn red when this function is activated.
Programming Play
You can set a programmed playback order for CD tracks on the 9000CDT. The
Programming mode is only accessible while playback is in ‘stop’ mode ie. no music
is playing.
To enter the programming mode, press the ‘PROG’ button on the remote
controller. Enter the first track that you would like to play by entering the track
number using the number pad on the remote. Press 'STORE' to save the chosen
track in position (1). Enter the next track number using the number pad, and press
'STORE' to save in position (2), and so on.
Sampling Frequency Bit Rate Bit Length Extension
WMA 32 / 44.1kHz 32~320kbps
MP3
WAV
AAC
*48kHz files can be played via the 9000CDT but will be resampled to 44.1kHz
Compatible with 'FAT12', 'FAT16' or 'FAT32' HDD devices.
Maximum number of files: 65,535
Maximum number of folders: 700
If the USB memory device is divided into multiple partitions, only the top partition can be accessed.
USB port 5V 1A mains output is used for supplying power to USB memory device. It is not
suggested to charge mobile phones or other USB devices via this port.
32 / 44.1kHz
32 / 44.1kHz 16bit
32 / 44.1kHz
32~320kbps
-
32~320kbps
-
-
-
.wma
.mp3
.wav
.m4a
Page 14
Important
Safety Information
Contents Getting Started
Controls and Functions Remote Handset
Connections
Menu Options
System Operations Playing Operations
Warranty Coverage
Specifications
10:
Audiolab warrants its products, subject to the following terms and conditions
below, to be free from defects in materials and workmanship.
Warranty Coverage
Online Registration
Scan the QR code using a smart-phone device,
for product warranty registration online.
The three (3) year extended warranty is applicable to items purchased from Jan
1st 2021, onwards. Items purchased prior to this date are not eligible for this
extended warranty service but are subject to statutory warranty claims and all
applicable consumer rights.
To qualify for the extended 3 year warranty, you must register your product
within ninety (90) calendar days from the date of purchase. Visit
audiolab.co.uk/warranty-registration to complete your online registration. Items
not registered online will have a Limited Warranty for one (1) year, or for the
period of your country’s statutory warranty, whichever is longer.
Warranty can only be offered to products registered with proof of purchase with
date, model and details of the authorised dealer clearly stated on the
receipt/invoice. Please keep the original receipt/invoice in case it is required for a
warranty claim.
This Limited Warranty is non-transferable and is offered exclusively to the original
owner.
This Limited Warranty is valid only in the original country of purchase.
Repairs or replacements are provided under this warranty are the exclusive
remedy of the consumer. Audiolab shall not be liable for any incidental or
consequential damages for breach of any expenses or implied warranty with any
product. Except to the extent prohibited by law, this warranty is exclusive and in
lieu of all other warranties whatsoever, both expressed and implied, including but
not limited to the warrant of merchantability and fitness for practical purpose.
This warranty provides benefits that are additional to and do not affect your
statutory consumer rights.
Page 14
This Limited Warranty offer is subject to correct information being submitted in
your application. Incorrect dates or mismatched purchase receipt dates that are
outside of the warranty terms will immediately invalidate any warranty claim.
*Please check with your dealer local distributor for further information.
Exclusions
The following items are excluded from the Audiolab warranty:
Normal wear and tear and cosmetic damage (including but not limited to any wear
from reasonable use, environmental deterioration or neglect)
Products on which the serial number has been removed, altered or otherwise
made illegible.
Products not purchased from an authorised Audiolab dealer.
Products that were not new at the time of original purchase.
Products sold ‘as is’, ‘as seen’ or ‘with faults’
Product not purchased from an Authorised Dealer/Distributor within the region of
the claim (ie parallel imports or grey market products)
Accidental damage or faults caused by commercial use, acts of God, incorrect
installation, incorrect connection, incorrect packaging, misuse or careless
operation or handling which is not in accordance with the user instructions.
Equipment that has been operated in conjunction with unsuitable, inappropriate
or faulty apparatus.
Repairs, alterations or modifications carried out by parties other than Audiolab or
its authorised service partners.
Damage in transit that cannot be attributable to the fault of Audiolab, the
authorised distributor or dealer (ie. claims otherwise covered by transit insurance.)
Faults relating to abnormal or inappropriate power supply voltage or power surges.
Faults relating to extremities in temperature, exposure to heat, water or other
liquids, insects, excessive moisture, sand, chemicals, battery leakage or any other
contaminants.
Any force majeure events, including but not limited to any acts of God, fire,
lightning, typhoon, storm, earthquake, hurricane, natural disaster, tsunami, flood,
war, riot, public disturbance.
Any other causes beyond the reasonable control of either Audiolab and its
Authorised Distributor.
Please note items purchased before 1st Jan 2021 are not eligible for the extended
warranty claim.
Page 15
Important
Safety Information
Contents Getting Started
Controls and Functions Remote Handset
Connections
Menu Options
System Operations Playing Operations
Warranty Coverage
Specifications
10:
Warranty Coverage
How to claim
To obtain warranty service please contact the authorised dealer from which you
purchased this product and present the limited warranty certificate offered upon
registration of your product’s extended warranty offer.
Do not dispatch goods without the prior agreement of the dealer distributor or
authorised service centre.
If asked to return products for inspection and or repair, please pack carefully
preferably in the original carton or packaging affording an equal degree of
protection and returned via insured, trackable courier service.
The authorised dealer or distributor will offer full return details and instructions.
However, please note if unsuitable packaging is used the warranty may be
deemed void due to improper action in return.
Audiolab or the authorised distributor, dealer or service centre may make a
charge for the supply of new packaging for the return of the repaired item. Please
note, insurance is recommended as goods are returned at the owner’s risk.
Authorised distributors or service centres cannot be held liable for loss or
damage in transit. insurance and freight charges on the return journey will be
paid for by Audiolab, authorised dealer, distributor or service centre if corrective
work proves to be necessary.
In the event of ‘no-fault found’ or ‘no repair necessary’, the return shipping charge
will be the responsibility of the owner.
Repairs
All repairs will be carried out by the appointed distributor (or locally appointed
service centre). Repairs handled or processed without authorisation or approval
of the appointed representative will be excluded from this limited warranty.
Please note, Audiolab is not able to supply parts or replacement items to any
other entity than the official distributor or authorised service centre.
Other than the warranty and services set out in this warranty, to the fullest extent
permitted by law, Audiolab shall not be liable to you and/or any third party or
entity whatsoever for:
Page 15
Any loss, damages and/or malfunction caused to any product(s) which is/are
•
connected to any of the products covered by this warranty.
Any damages, loss and liability, whether direct, indirect, incidental,
•
consequential special, punitive or otherwise, howsoever caused by, arising out
of or otherwise, in relation to the installation, delivery, use, service, repair,
replacement and/or maintenance of the product;
Any damages, loss and liability under this warranty in respect of any act,
•
omission, or negligence of any of their technicians, employees, agents,
representatives or independent contractors relating to the actual or purported
performance of any of the obligations under this warranty.
Service Centre Address
Should a fault occur with your product, please pack it correctly using the original
packing, so you can ship it safely. For technical support, servicing or product
queries and information, please contact either your local retailer or the office
below:
IAG Service Dept.
13/14 Glebe Road
Huntingdon
Cambridgeshire
PE29 7DL
UK
Tel: +44(0)1480 452561
Email: [email protected]
For information on other authorised service centres worldwide contact Audiolab
International, UK.
A worldwide distributors list is available on the Audiolab website:
www.audiolab.co.uk
Page 16
Important
Safety Information
Contents Getting Started
Controls and Functions
Remote Handset
Connections
Menu Options
System Operations
Playing Operations
Warranty Coverage
Specifications
11.Specifications
Model
General Description
USB Storage Device Audio Format
USB Storage Device File System
Digital Output Amplitude
Output Impedance
Frequency Response
Total Harmonic Distortion (THD)
Sampling Rate
Digital Output Interface
Standby Power Consumption
Power Requirements (according to region)
Product Size (mm) (W x D x H)
Carton Size (mm) (W x D x H) 514 x 470 x 161
Net Weight 5.74kg
Gross Weight 7.6kg
9000CDT
CD Transport and USB HDD player
MP3, WMA, AAC, WAV file compatible
FAT12, FAT16 and FAT32 device compatible
500 +/-50mVpp
75Ω
-0.01dB (20Hz-20kHz, ref.1 kHz)
< 0.002%
44.1kHz (48kHz files can be played via the 9000CDT
but will be resampled to 44.1kHz)
1 x Coaxial , 1 x Optical
< 0.5W
220-240V - 50/60Hz
100-120V - 50/60Hz
444 x 322 x 89
Page 16
Page 17
Page 18
Audiolab
IAG House,
13 /14 Glebe Road,
Huntingdon,
Cambridgeshire,
PE29 7DL,
UK
Telephone: +44(0)1480 452561
Email: [email protected]
http://www.audiolab.co.uk
Loading...