Aube Technologies TH209 User Manual

Heating intensity indicator. No image appears when heating is off.

This thermostat can be used to control an electric heating system such as a baseboard heater, a radiant floor,a radiant ceiling, or a convector.

The thermostat CANNOT be used with:

• a resistive load under 0.83 A

• a resistive load over 8.3 A

• a system driven by a contactor or a relay (inductive load)

• a fan-forced heating system (e.g. : fan-forced convector)

• a central heating system

Description

Temperature display

Up button Down button

Temperature adjustment

}

buttons

TH209

User Guide

Electronic Thermostat

Connect any one of thermostat wires to the heater (load) wire and the other one to the power supply wire using solderless connectors for copper wires. (The thermostat wires are non-polarized; either wire can be connected to the load or to the power supply.)

NOTE: All cables and connections must conform to the local electri-

cal code. Special CO/ALR solderless connectors must be used when connecting with aluminium conductors.

2-wire installation

SUPPLIED PARTS

• One (1) thermostat

• Two (2) 6-32 mounting screws

• Two (2) solderless connectors

TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRIC SHOCK.

Loosen the screw holding the faceplate to the base. Th e screw cannot be completely removed and remains captive on the base. Remove the faceplate from the base by pulling the bottom half.

Installation

4-wire installation

Install the base onto an electrical box.

Reinstall the faceplate on the base and secure it in place with the screw.

NOTE: Keep the air vents of thermostat clean and unobstructed at all times.

TH209 400-209-000-A 2008-06-19 1/2

Selecting the Temperature Format

Troubleshooting

To select the temperature display format:

n Press the Up and Down buttons for three seconds.

The format currently used will be indicated on the screen.

o Press the Up or Down button to change the

format.

p P

ress

the Up and Down buttons

wait for one minute) to return to the normal display

The thermostat normally displays the actual (ambient) temperature.

• To view the setpoint temperature, press once on

• To change the setpoint temperature, press the

During a power outage, the setpoint is saved in memory. You do not need to adjust the temperature when power returns.

- Supply: 120/240 VAC, 50/60 Hz

- Minimum load: 0.83 A (resistive only)

- Maximum load:8.3 A (resistive only)

- Display range: 0 °C to 50 °C (32 °F to 122 °F)

- Setpoint range: 5 °C to 30 °C (40 °F to 85 °F)

- Storage: -20 °C to 50 °C (-4 °F to 120 °F)

- Heating cycle length: 15 seconds

- Approval:

Temperature Display and Setting

either temperature adjustment button. The setpoint will be displayed for 5 seconds. The icon

appears during the setpoint display.

appropriate button until the desired value is displayed.

Power Outage

Specifications

200 W @ 240 VAC 100 W @ 120 VAC

2000 W @ 240 VAC 1000 W @ 120 VAC

for one second (or

PROBLEM SOLUTIONS

This is normal. Under normal operation, the ther-

Thermostat is hot.

Displayed tempe-

rature is wrong.

Display disappears and reappears after a few minutes.

;

Aube warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Aube shall repair or replace it (at Aube's option). If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the place

(ii) contact Aube. Aube will make the determination whether the product

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Aube that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Aube's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states or regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREEYEAR DURATION OF THIS WARRANTY. Some provinces, states or regions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from one province, state or region to another.



Warranty

from which you purchased it, or

should be returned, or whether a replacement product can be sent to you.

Technical assistance

mostat housing can reach a temperature between 35 °C (95 °F) and 40 °C (104 °F).

Remediate if any the following conditions applies:

• The thermostat is exposed to air draft.

• The sticker on the thermostat’s screen has not been removed.

• The thermostat is located near or above a heat source such as a light dimmer.

The thermal protection device on the heater has temporarily opened. This can happen if the heater is obstructed by furniture or curtain and has overheated, or if the heater’s thermal protection device is too sensitive.

705 Montrichard Saint-Jean-sur-Richelieu, Quebec J2X 5K8 Canada

Tel.: (450) 358-4600 Toll-free: 1-800-831-AUBE Fax: (450) 358-4650 Email: aube.service@honeywell.com

For more information on our products, go t o

www.aubetech.com

TH209 400-209-000-A 2008-06-19 2/2