Thank you for choosin g an Aube product.
The TH131 and TH133 non programmable thermostats
are equipped with a microprocessor and proportional
integral adaptive (PIA) temperature control technology.
They can be installed on a 230 V power base (European
model) or a 24 V low voltage base and combined with an
electromechanical or TRIAC relay.
The TH131 can use all six pilot wire commands when
installed on a 230 V power base (see section 4).
7HPSHUDWXUH&RQWURO$DQG $)RQO\
Position the switch according to your application:
+HDWLQJ &\FOHV
Ͽ
230 V LINE VOLTAGE BASE
ALWAYS 15 minutes
Ͽ
24 V LOW VOLTAGE BASE
•15 MIN
Use with a TRIAC or
electromechanical relay.
Recommended for mechanical
actuated system (water heating
using a solenoid valve, etc.) or a
fan-forced heater.
• 15 SEC
Use only for installations with a solid state relay
(SSR). Recommended for electric heating
(baseboards, convectors, etc.).
212))6ZLWFK 7+ RQO\
The thermostat also features an On/Off switch making it
possible to turn off the thermostat when it is not required
(e.g. summer).
Use this feature to establish a temperature range by
setting minimum and maximu m setpoints. Depending on
the model, you can establish the temperature range for:
Ͽ
the ambient air (A)
Ͽ
the floor (AF and F)
Use a flat tip screwdriver to
rotate the potentiometers
until the notch points to the
desired temperature.
([DPSOH
When the temperature is
set outside the temperature
range, it will revert to the
nearest setpoint.
Example: MIN is 59°F and MAX is 77°F.
Ͽ
Using the front dial, you set the temperature at 50°F,
the TH131 will revert to the minimum set value 59°F.
Ͽ
Using the front dial, you set the temperature at 86°F,
the TH131 will revert to the maximum set value 77°F.
TH1 31 & TH1 33 A/AF/F
User Guide
Control Module
TH133
Heating command
Indicator
Temperature
selection dial
ON/OFF switch
TH131
Pilot wire
indicator
(European
model only
230 V
Model Switch Temperature Control
A UP (A/AF)
AMBIENT
(no floor sensor)
AF UP (A/AF)
AMBIENT WITH FLOOR LIMIT
(requires a floor sensor)
F DOWN (F)
FLOOR
(requires a floor sensor)
(ambient sensor is deactivated)
Configure the Switches
Min/Max Temperature (TH1 31 only)
Align the bracket tabs on the control module with the
holes located on the power base and secure using the
screw.
NOTE: Keep the thermostat's air vents clean and free
from obstructions.
NOTE: The screw cannot be removed completely.
EUROPEAN MODEL ONLY (230 V BASE)
The TH131 accepts the six pilot wire commands:
Models: TH131 and TH133 A / AF / F
Setting Range : 45°F, 59°F to 95°F (7°C, 15°C to 35°C)
MIN: above-freezing temperature 45°F (7°C)
MAX: maximum temperature 95°F (35°C)
Potentiometers:
MIN: 41°F to 77°F (5°C to 25°C)
MAX: 59°F to 95°F (15°C to 35°C)
Storage: -4°F to 120°F (-20°C to 50°C)
Software: Class A
Controller: Electronic
Temperature Control: Proportional integral adaptive,
15-minute or 15-second heating cycles
Accuracy: ± 0.36°F (0.2°C)
Size (H/W/D):
TH131: 3.1 x 3.1 x 0.64 in (78.9 x 78.9 x 16.3 mm)
TH133: 3.1 x 3.1 x 0.71 in (78.9 x 78.9 x 18 mm)
AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY
This product is guaranteed ag ainst workmanship defects for a two-year
period following the initial date of purchase. During this period, AUBE
Technologies Inc. will repair or replace, at our option and without charge,
any defective product which has bee n used under normal conditions.
The warranty does not cover delivery costs and does not ap ply to products
poorly installed or randomly damaged following installation. This warranty
cancels and replaces any other manufacturer's express or implied
warranty as well as any other compa ny commitment.
AUBE Technologies Inc. cannot be he ld liable for related or rando m
damages following the installation of this product. The defective product as
well as the purchase invoice must be return ed to the place of purchase or
mailed, prepaid and insured, to t he nearest address.
If you have any questions concerning the TH131 or TH133 the rmostat, call
our technical support team at:
Install the Control Module
Control Module
Power Base
MODE
1
1. 1) Comfort 2) Reduced setpoint 3) Ab ove freezing (min)
4) Stop heating 5) 1°C setback 6) 2°C setback
SIGNAL COMMAND
1 No signal
Heating as per
defined setpoint
2
Current setpoint
minus 3,5°C
3 Setpoint at 7°C
4 Stop heating
5
Current setpoint
minus 1°C
6
Current setpoint
minus 2°C
Pilot Wire Commands
T
echnical Specifications
W
arranty and Service
705 Montrichard
Saint-Jean-sur-Richelieu
Quebec, Canada J2X 5K8
Tel.: (450) 358-4600
Toll Free: 1-800-831-AUBE
Fax: (450) 358-4650
service@aubetech.com
10 rue Ampère
95500 Gonesse
France
33 (0) 1 34 07 99 00
33 (0) 1 34 07 99 19
advaube@comintes.com
13/01/2004 400-131-002-B
Included Parts
n One (1) PB130-230 power base
o One (1) floor sensor (for AF and F control modules only)
p One (1) wall plate (optional, in certain countries)
PB1 30A-230
Installation Instructions
230 V Lin e Voltage Power B ase
Technical Specifications
Model: PB130A-230
Supply: 230 VAC, 50 Hz
Load: 15 A maximum (resistive only)
Power: 3450 Watts (NI) @ 230 VAC
Conformity: EN60730-2-9 / EN50081-1 / EN50082-2
Storage: -20°C to 50°C
Protection:Class 2
Protection degree:IP20
Automatic action:Type 1.B
Environment: Normally polluted
Size (H•W•D): 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm)
NOTE: The terminals are designed to handle a cross-section of
wire measuring 0.33 to 3.1 mm
2
.
AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY
This product is guaranteed against workmanship defects for a twoyear period following the initial date of purchase. During this period,
AUBE Technologies Inc. will repair or replace, at our option and
without charge, any defective product which has been used under
normal conditions.
The warranty does not cover delivery costs and does not apply to
products poorly installed or randomly damaged following
installation. This warranty cancels and replaces any other
manufacturer's express or implied warranty as well as any other
company commitment.
AUBE Technologies Inc. cannot be held liable for related or random
damages following the installation of this product. The defective
product as well as the purchase invoice must be returned to the
place of purchase or mailed, prepaid and insured, to the nearest
location.
If you have any questions concerning the installation of the
PB130-230 power base, contact our technical support team at:
705 Montrichard
Saint-Jean-sur-Richelieu
Quebec, Canada J2X 5K8
Tel.: (450) 358-4600
Toll Free: 1-800-831-AUBE
Fax: (450) 358-4650
Email: service@aubetech.com
10 rue Ampère
95500 Gonesse
France
33 (0) 1 34 07 99 00
33 (0) 1 34 07 99 19
advaube@comintes.com
For more information on our products, visit us at
www.aubetech.com
Introduction
The PB130-230 power base is used to power a TH13x Series
control module. The resistive load must not exceed 3450 watts
(NI) @ 230 VAC (15 A).
Installation Guidelines
Turn off power to the heating system at the main power panel
to avoid electrical shock. Installation should be carried out by
an electrician.
ߧ
All work must conform to the applicable country standards for
electrical installations and wiring.
ߧ
This thermostat should be connected on a circuit equipped
with a fuse or a circuit breaker. It must be installed on a
certified electrical box.
ߧ
For a new installation, choose a location about 1.5 m above
the floor.
ߧ
For electric baseboards, convectors and fan-forced heaters,
the thermostat must be installed facing the heating system.
ߧ
The thermostat must be installed on an inside wall.
ߧ
Avoid locations where there are air drafts (top of staircase, air
outlet), dead air spots (behind a door), direct sunlight or
concealed chimneys or stove pipes.
n Remove the screw holding the
control module to the power base
and lift the lower part upwards. The
screw cannot be completely
removed.
o Before making the connections, make sure
that the base covers the electrical box
entirely. If not, install a wall plate at the
back of the base as shown.
p Connect the wires:
• Power:
Terminals 1 & 5
• Load:
Terminals 2 & 4
see note 1
• Pilot Wire:
Terminal 3
see note 2
• Floor sensor:
Terminals 6 & 7
(no polarity)
see note 3
Note 1 If a contactor is used between the thermostat and the load,
install a snubber at the contactor’s coil terminal to ensure
the proper operation of the thermostat.
Note 2 This connection is required on some models only.
Note 3 For the proper operation of the thermostat, the floor sensor
must be centered between two heater wires having a
maximum temperature of 80°C. The floor sensor wire must
not cross any heater wire or be placed close to it.
r Push wires into the electrical box and
secure the base to the electrical box
anchorage. The head of the screw must
be less than 2 mm thick.
s BEFORE installing the control
module onto the base, set the
configuration switches (if any) on
the control module (refer to the
user guide).
WARNING: This power base must be
used only with 15-minute heating cycles. If your control module
has a selector switch for choosing the heating cycle, ensure that the
switch is correctly set.
t Return power to the heating system.
12/8/04 400-130-001-D
Installation and Wiring
Loading...