ATV NVW2212M, NVW2212MB, NVW229, NVW229B, NVW237 User Manual

USER MANUAL

VP DOME NETWORK CAMERA

Please read this manual thoroughly before use and keep it handy for future reference.

2

WARNING

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX­POSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY
METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER
OPENNINGS ON THE EQUIPMENT.

CAUTION

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is in- tended
to alert the user to the presence of dangerous voltage within the products enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.

3

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful inter­ference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

FCC INFORMATION: This equipment has been tested and found to

comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commer­cial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the in­struction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful in­terference in which case the user will be required to correct the interference
at his own expense.

CAUTION: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the
equipment.

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil nume

`

rique de la classe A est conforme a

´

la norme NMB-003 du

Canada.

WARNING

This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

CE COMPLIANCE STATEMENT

4

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of
time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.

15. CAUTION : These servicing instructions are for use by qualified service personnel only. To
reduce the risk of electric shock do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.

16. ITE is to be connected only to PoE networks without routing to the outside plant.

17. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or
“LPS” and rated from 12 Vdc, 710 mA.

18. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af
shall be a UL Listed device with the output evaluated as a Limited Power Source as defined
in UL60950-1.

19. Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As
such, associated Ethernet wiring shall be limited to inside the building.

20. CAUTION : Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
ATTENTION : II y a danger d’explosion s’il y a remplacement incorrect de la batterie.

Remplacer uniquement avec une batterie du même type ou d’un type équivalent

recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.

5

Contents

1 Introduction 6

1.1 Components 6

1.2 Key Features 7

2 Installation 8

2.1 Overview 8

2.2 Connection 10

2.3 Resetting to the factory default settings 11

2.4 Network Connection & IP assignment 12

3 Operation 13

3.1 Access from a browser 13

3.2 Access from the internet 14

3.3 Setting the admin password over a secure connection 14

3.4 Live View Page 15

3.5 Playback 17

3.6 Network Camera Setup 19

3.6.1 Basic Configuration 19

3.6.2 Video & Image 24

3.6.3 Audio 33

3.6.4 Event 34

3.6.5 System 59

3.7 Help 80

A Appendix 81

A.1 Troubleshooting 81
A.2 Alarm Connection 82
A.3 Preventive Maintenance 82
A.4 System Requirement for Web Browser 83
A.5 General Performance Considerations 83
A.6 Product Specification 84

6

1 Introduction

The network camera supports the network service for a sensor image with progressive scan, which
can be monitored on a real-time screen regardless of distances and locations. By using its
dedicated program, many users are able to have an access to the network camera at once or a
single user can monitor various network cameras at the same time. It also enables users to play,
store and retrieve a monitoring image by using a PC. All the settings and real-time monitoring
screens are also provided through an access to the web.

The network camera is fully featured for security surveillance and remote monitoring needs. It is
based on the DSP compression chip, and makes it available on the network as real-time, full frame
rate Motion JPEG, H.264 and H.265 video streams.

The alarm input and alarm output can be used to connect various third party devices, such as,
door sensors and alarm bells.

1.1

This system comes with the following components;

Note 1. Check your package to make sure that you received the complete system, including all

Note 2. Adapter for DC 12V is not supplied.

Components

Network Camera 1
Installation Guide/CD 1
Template Sheet 1
Accessory Kit 1

components listed above.

7

1.2

Key Features

•

Brilliant video quality

The network camera offers the highly efficient H.265 or H.264 video compression, which
drastically reduces bandwidth and storage requirements without compromising image quality.
Motion JPEG is also supported for increased flexibility.

•

Quad streams

The network camera can deliver four video streams simultaneously using H.264, H.265 and
Motion JPEG. This means that several video streams can be configured with different
compression formats, resolutions and frame rates for different needs.

•

Intelligent video capabilities

The network camera includes intelligent capabilities such as enhanced video motion
detection. The network cameras external inputs and outputs can be connected to devices
such as sensors and relays, enabling the system to react to alarms and activate lights or
open/close doors.

•

Improved security

The network camera logs all user access, and lists currently connected users. Also, its full
frame rate video can be provided over HTTPS.

•

PoE (Power over Ethernet)

This network camera can be powered through PoE (IEEE802.3af), which simplifies installation
since only one cable is needed for carrying power, as well as video controls.

•

ONVIF certificate

This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility,
reduced cost, and future-proof systems.

•

Micro-SD recording support

The network camera also supports a micro-SD memory slot for local recording with removable
storage of type SDHC and SDXC.

•

Audio support

The Network Camera also supports two-way audio.

8

2 Installation

NO

Item

Description

1 RJ-45

Ethernet, RJ-45 port compatible
with 10/100Mbps PoE Modular Jack

2

DC Jack

Main Power, DC Jack, DC12V

3

AI: Alarm In

Alarm input and output, 3pin terminal
G: GND

AO: Alarm Out

4

MIC: Audio In

Audio line input, 2pin terminal

G: GND

5

SPK: Audio Out

Audio line output, 2pin terminal

G: GND

For the operation of the network camera, it is necessary to connect a network cable for data
transmission, power connection from power adapter. Depending on operation methods, it is
possible to connect an alarm cable additionally. For its fixation on different locations, please
consult with an installer.

2.1

Overview

 Dimension

Dimensions Unit: mm

 Extension Cable

9

 Installing & Adjusting Camera

Carefully remove the contents from the box.

1)

Loosen the four torx screws located the front of the housing leaving the screws intact in the
front portion.

2)

Make mounting holes and cable hole in the place(ceiling or wall) to which this dome.
Camera is installed using the template sheet.

Do not continue to turn the camera in same direction.
The cable connector can be detached.

10

2.2

Remove the cap at bottom of the camera to insert the SD memory card.

Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over
cable is used for directly connection to PC, while a direct cable is used for connection to a hub. You
can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.

Connection



Micro SD memory slot on the Bottom Board



Connecting to the RJ-45



Connecting Alarms

AI(Alarm In): You can use external devices to signal the network camera to react on

events. Mechanical or electrical switches can be wired to the AI (Alarm In) and G (Ground)
connectors.
G(Ground): Connect the ground side of the alarm input and/or alarm output to the G (Ground)
connector.
AO(Alarm Out): The network camera can activate external devices such as buzzers or lights.
Connect the device to the AO (Alarm Out) and G (Ground) connectors.



Connecting the Power

Connect the power of 12VDC for the network camera. Connect the positive(+) pole to the ‘+’ position
and the negative (-) pole to the ‘-’ position for the DC power.

–

Be careful not to reverse the polarity when connecting the power cable.

–

A router featuring PoE (Power over Ethernet) can also be used to supply power to the
camera.

–

For the power specifications, refer to the appendix, product specification.

–

If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.



Connecting Audio

Connect speaker to audio line output and external Mic to audio input line.



Connecting Test Monitor Out(CVBS)

Connect 3pin test video cable(Optional) to check test video.

11

2.3

Resetting to the factory default settings

To reset the network camera to the original factory settings, go to the Setup > System >
Maintenance web page (described in “System > Maintenance” of User Manual) or use the Reset
button on the network camera inside the bottom cap.



Using the Reset button:

Follow the instructions below to reset the network camera to the factory default settings using the
Reset button.

1)

Switch off the network camera by disconnecting the power adapter.

2)

Open the top cap.

3)

Press and hold the Reset button with a straightened paperclip while reconnecting the
power.

4)

Keep the Reset button pressed about 5 or more seconds.

5)

Release the Reset button.

6)

The network camera resets to factory defaults and restarts after completing the factory reset.

7)

Close the bottom cap tightly to ensure waterproof.

CAUTION: When performing a Factory Reset, you will lose any settings that have been

saved. (Default IP 192.168.30.220)

12

2.4

The camera supports the operation through the network. When a camera is first connected to the
network, it is necessary to allocate an IP address to the device with the “SmartManager” utility on
the CD. (Default IP 192.168.30.220)

1)

2)

window will display, and after a short while any network devices connected to the network will be
displayed in the list.

3)

as below.

Network Connection & IP assignment

Connect the network camera/device to the network and power up.

Start SmartManager utility (Start > All programs > SmartManager > SmartManager). The main

Select the camera on the list and click right button of the mouse. You can see the pop-up menu

4)

Select Assign IP Address. The Assign IP window will display. Enter the required IP address.

NOTE: For more information, refer to the SmartManager User Manual.

13

3 Operation

The network camera can be used with Windows operating system and browsers. The rec­ommended browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with
Windows.

NOTE: To view streaming video in Microsoft Internet Explorer, set your browser to allow
ActiveX controls.

3.1

Access from a browser

•

Start a browser (Internet Explorer).

•

Enter the IP address or host name of the network camera in the Location/Address field of your
browser.

•

You can see a starting page. Click Live View, Playback, or Setup to enter web page.

•

The network cameras Live View page appears in your browser.

14

3.2

Once connected, the network camera is accessible on your local network (LAN). To access the
network camera from the Internet you must configure your broadband router to allow incoming
data traffic to the network camera. To do this, enable the NAT traversal feature, which will attempt
to automatically configure the router to allow access to the network cam- era. This is enabled from
Setup > System > Network > NAT. For more information, please see “ System > Network > NAT”
of User Manual.

Access from the internet

3.3

To gain access to the product, the password for the default administrator user must be set. This is
done in the “Admin Password” dialog, which is displayed when the network camera is accessed for
the setup at the first time. Enter your admin name and password, set by the administrator.

Setting the admin password over a secure connection

NOTE: The default administrator user name and password is “admin”. If the password is lost, the

network camera must be reset to the factory default settings. Please see “Resetting to the factory
default settings.”

To prevent network eavesdropping when setting the admin password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see NOTE below). To set the
password via a standard HTTP connection, enter it directly in the first dialog shown below. To set the
password via an encrypted HTTPS connection, please see “System
> Security > HTTPS” of User Manual.

NOTE: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic
between web browsers and servers. The HTTPS certificate controls the encrypted exchange of
information.

15

3.4

Live View Page

The Live View page comes in several screen modes. Users are allowed to select the most
suitable one out of those modes. Adjust the mode in accordance with your PC specifications and
monitoring purposes.

1)

General controls

Live View Page Playback Page Setup Page Help Page

The video drop-down list allows you to select a customized or pre-

programmed video stream on the Live View page. Stream profiles are con­figured under Setup > Basic Configuration > Video & Image. For more in-

2)

Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following
buttons:

The Stop button stops the video stream being played. Pressing the key again toggles

start and stop. The Start button connects to the network camera or starts playing a video
stream.

The Pause button pauses the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

saved can be specified.

formation, please see “Basic Configuration > Video & Image” of User Manual.

The resolution drop-down list allows you to select the most suitable one out

video resolutions to be displayed on Live View page.

The protocol drop-down list allows you to select which combination of protocols

and methods to use depending on your viewing requirements, and on the
properties of your network.

of

the

image is

16

The Digital Zoom button activates a zoom-in or zoom-out function for video image on

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the ‘Esc’ button on the computer keyboard to cancel full screen
view.

the live

The Manual Trigger button activates a pop-up window to manually start or stop the

The Lens Control button allows user to control Zoom and Focus manually. (This Icon

appears for motorized lens model only.)

•

Zoom: Click “ ” button to zoom out and click “ ” button to zoom in. Or drag the bar
to adjust the zoom. The focus is moved slightly after adjusting zoom; adjust the focus
again, as necessary.



Focus: Click “ ” button to Near focus and click “ ” button to Far focus. Or drag the
bar to adjust the focus.



Smart Focus User can get automated focus here.

event.



Calibrate Calibrate focus and zoom.

The Smart Focus button activates smart focus function which set the focus to the

optimum position. (This Icon appears for motorized lens model only.)

The Relay Output button manually triggers relay out. (This Icon appears only if “Enable

alarm out” is selected in “Event Out - Alarm Out”.)

The Speaker button activates/deactivates external speaker.

The Mic button activates/deactivates microphone input.

Use this scale to control the volume of the speakers and microphones.

3)

Video Streams

The network camera provides several images and video stream formats. Your requirements and
the properties of your network will determine the type you use.

The Live View page in the network camera provides access to H.264, H.265 and Motion JPEG
video streams, and to the list of available video streams. Other applications and clients can
also access these video streams/images directly, without going via the Live View page.

17

3.5

Playback

The Playback window contains a list of recordings made to the memory card. It shows each
recording’s start time, length, the event type used to start the recording, calendar and time slice bar
indicates if the recording is existed or not.

The description of playback window follows.

1)

Video Screen

You can see the video screen when playing the video clip in the Micro SD memory.

2)

Playback Buttons

To view a recording data in the SD local storage, select it from the list and click the
Playback buttons.

Go to the first: go to the beginning of the video clip.
Fast backward play: fast play backward of the video clip.

Backward play: play backward of the video clip.

Step backward play: go back one frame of the video clip.

Pause: pause playback of the video clip.

Step forward play: go forward one frame of the video clip.

Forward Play: play forward the video clip.

Fast forward play: play fast forward of the video clip. Go

to the last: go to the end of the video clip.

Clip copy: copy the video clip.

Zoom In: zoom in the video clip.

Full Screen: display full screen of the video.

18

3)

Time Chart

Display an hour-based search screen for the chosen date. If there is recording data, a blue
section will be displayed on a 24-hour basis. If you select a particular hour in the chart, a
yellow square on the hour will be displayed.

4)

Speaker Control Bar

Use this scale to control the volume of the speakers.

5)

Search Calendar

Search results from the SD local storage in the network camera connected are displayed
monthly. If there is a recorded data for a particular date, a blue square on the date will be
displayed. If you select a particular date in the calendar, a yellow square on the date will be
displayed.

6)

Play Time

Displays time of the video playing.

7)

Event Search Window

Select a search option in the drop-down list and click GO button. You can also enter the
time period for searching. If you click Start Date or End Date zone, displays Search Calendar.

8)

Event List Window

Event List displays the event(s) that were recorded in the SD local storage. Select a list and
click the play button. The video clip will be played.

19

3.6

Network Camera Setup

This section describes how to configure the network camera.
Administrator has unrestricted access to all the Setup tools, whereas Operators have access to the

settings of Basic Configuration, which are Live View, Video & Image, Audio, Event and System.
You can configure the network camera by clicking Setup either in the first connection page or the

top second-right button of the Live View page. Accessing the network camera from a computer for
the first time opens the Admin Password dialog box. Enter your administrator or operator id and
password to get into setup page.

NOTE: If the password is lost, the network camera must be reset to the factory default

settings. Please see “Resetting to the Factory Default Setting”.

3.6.1 Basic Configuration

You can see the device information in this information page.

20

1)

User Group

Authority

Guest

Provides the lowest level of access, which only allows access
to the Live View page.

Operator

An operator can view the Live View page, create and modify
events, and adjust certain other settings. Operators have no
access to System Options.

Administrator

An administrator has unrestricted access to the Setup tools
and can determine the registration of all other users.

Users

User access control is enabled by default. The administrator can set up other users, by giving
user names and passwords. It is also possible to allow anonymous viewer login, which means
that anybody may access the Live View page, as described below:

The user list displays the authorized users and user groups (levels):

Please refer to “ System 2) Security Users” for more details about User setup.

21

2)

Network

The network camera supports both IP version 4 and IP version 6. Both versions may be enabled
simultaneously, and at least one version must always be enabled. When using IPv4, the IP
address for the network camera can be set automatically via DHCP, or a static IP address can be
set manually. If IPv6 is enabled, the network camera receives an IP ad- dress according to the
configuration in the network router. There is also an option of using the Internet Dynamic DNS
Service. For more information on setting the network, please see “System > Network > Basic”.

•

•

NOTES:

1.

Obtain IP address via DHCP: Dynamic Host Configuration Protocol (DHCP) is a protocol
that lets network administrators centrally manage and automate the assignment of IP
addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly
used to set an IP address dynamically, it is also possible to use it to set a
static, known IP address for a particular MAC address.

Use the following IP address: To use a static IP address for the network camera, check the
radio button and then make the following settings:

–

IP address: Specify a unique IP address for your network camera.

–

Subnet mask: Specify the mask for the subnet the network camera is located on.

–

Default router: Specify the IP address of the default router (gateway) used for

connecting devices attached to different networks and network segments.

DHCP should only be enabled if using dynamic IP address notification, or if your DHCP server
can update a DNS server, which then allows you to access the network camera by name (host
name). If DHCP is enabled and you cannot access the unit, you may have to reset it to the
factory default settings and then perform the installation again.

2.

The ARP/Ping service is automatically disabled two minutes after the unit is started, or as
soon as an IP address is set.

3.

Pinging the unit is still possible when this service is disabled.

Please refer to “System > Network > Basic” for more details about Network setup.

22

3)

Video & Image

User can setup and change setting of individual video stream in this page.

Please refer to “Video & Image > Basic” for more details about Video & Image setup.

23

4)

Audio

The network camera can transmit audio to other clients using an external microphone and can
play audio received from other clients by attaching a speaker. User can setup and change
setting of Audio in this page.

Please refer to “Audio” for more details about Audio setup.

5)

Date & Time

User can set time directly or assign time server to get the current time, as well as determine Date &
Time format in this page.

Please refer to “System > Date & Time” for more details about Date & Time setup.

24

3.6.2 Video & Image

1)

Basic

•

Sensor Setting:

– Capture mode: User can select sensor capture mode between 1920x1080(2MP)

/2592x1520(4MP) and NTSC/PAL (Some models are fixed to NTSC or PAL).

•

Stream 1 Setting:

–

Codec: The codec supported in Stream 1 is H.264 and H.265

There are 3 pre-programmed stream profiles available for quick set-up. Choose the
form of video encoding you wish to use from the drop-down list:

·

H.264 High Profile:
Primary profile for broadcast and disc storage applications, particularly for high-

definition television applications (for example, this is the profile adopted by the Blu­ray Disc storage format and the DVB HDTV broadcast service).

·

H.264/H.265 Main Profile:
Primary profile for low-cost applications that require additional error robustness,
this profile is used rarely in videoconferencing and mobile applications; it does add

additional error resilience tools to the Constrained Baseline Profile. The importance
of this profile is fading after the Constrained Baseline Profile has been defined.

·

H.264 Baseline Profile:
Originally intended as the mainstream consumer profile for broadcast and storage

25

applications, the importance of this profile faded when the High Profile was developed
for those applications.

–

Resolution:

This enables users to determine a basic screen size when having an access
through the Web Browser or PC program. The screen size control comes in several
modes. Users can change the selected screen size anytime while monitoring the screen
on a real-time basis.

–

Bitrate control:

The bit rate can be set as Constrained Bit Rate (CBR) or Constrained Variable Bit Rate
(CVBR). Limiting the maximum bit rate helps control the bandwidth used by the H.264 or
H.265 video stream. Leaving the Maximum bit rate as unlimited maintains consistently
good image quality but increases bandwidth usage when there is more activity in the image.
Limiting the bit rate to a defined value prevents excessive bandwidth usage, but images are
degraded when the limit is exceeded.

·

CBR: Constrained bitrate.

·

CVBR: VBR with maximum bitrate which is set in Bitrate.

–

Bitrate: Maximum bitrate for CBR in the range of 100kbps ∼ 10Mbps.

–

Frame rate:

Upon the real-time play, users should select a frame refresh rate per second. If the rate
is high, the image will become smooth. On the other hand, if the rate is low, the image
will not be natural but it can reduce a network load.

–

GOP size:

Select the GOP (Group of Picture) size. If users want to have a high quality of fast
image one by one, please decrease the value. For the purpose of general monitoring,
please do not change a basic value. Such act may cause a problem to the system
performance. For the details of GOP setting, please contact the service center.

•

Stream 2 Setting:
Sometimes the image size is large due to low light or complex scenery. Adjusting the

frame rate and quality helps to control the bandwidth and storage used by the Motion JPEG
video stream in these situations. Limiting the frame rate and quality optimizes bandwidth and
storage usage, but may give poor image quality. To prevent increased bandwidth and storage
usage, the Resolution, Frame rate, and Frame Quality should be set to an optimal value.

–

MJPEG Resolution: Same as the stream 1 setting.

–

MJPEG Frame rate: Same as the stream 1 setting.

–

MJPEG Quality: Select the picture quality. If users want to have a high quality of fast

image one by one, please decrease the value. For the purpose of general monitoring,
please do not change a basic value. Such act may cause a problem to the system
performance.

•

Stream 3, Stream4 Setting: Same as the Stream 1 settings.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

26

2)

Privacy Masking

The privacy masking function allows you to mask parts of the video image to be transmitted. You can
set up to eight privacy masks.

The privacy masks are configured by Mask windows. Each window can be selected by clicking with
the mouse. It is also possible to resize or delete, or move the window, by selecting the appropriate
window at the mouse menu on the video screen.

To create a mask window, follow steps:

1.

Click the right button of mouse to see the mouse menu.

2.

Select New Privacy Mask in the mouse menu.

3.

Click and drag mouse to designate a mask window area.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

27

4)

Hi-Stream

The Hi-Stream function allows reduce bandwidth by using compression and frame rate control.

• Enable ROI: Select ‘Enable ROI’ to active Hi-Stream function. Video mode will be fixed to CVBR.

- Create region: Click the right button of mouse and select New ROI Area.
Click the left button of mouse and drag to make window.

- Delete Region: Click the right button of mouse and select the region.
Click Delete or click X from the region table.

- ROI Quality: Set quality of the selected area.

- Non-ROI Quality: Set quality of the non-selected area.

- Non-ROI fps: Set frame rate of the non-selected area.

28

5)

Camera Setup

In this page, user can setup Exposure Control, White Balance Control, Image Appearance, and
Day & Night control.

•

Video Preview: User can check the setting via video preview pop-up window

29

•

Exposure Control

–

Mode: Determines exposure mode among automatic and flicker-free modes.

Users can use Automatic mode with full shutter speed or Flicker-free mode with a limited
range of shutter due to an anti-flicker function.

–

Max. gain: Sets maximum gain threshold.

–

Shutter: Sets shutter speed of the sensor. If users set Automatic, Max shutter and Min

shutter can be selected.
If the object is as fast as a car, please change the Max shutter to a faster value (eg 1/10 ->

1/120). If users set Manual, fixed shutter speed can be selected.
Note: If the shutter speed is set Manual, the screen may be saturated or dark.

–

Max. shutter: Users can set the limit for slow shutter speeds used in dark environments.

–

Min. shutter: Users can set the limit for fast shutter speeds used in bright environments.

–

Enable P-IRIS: Check this box to activate the P-IRIS function

If users set Automatic, users can specify the range of P-IRIS to be used, and P-IRIS is
automatically adjusted according to the amount of light around the camera.
If users set Manual, P-IRIS is fixed.
(Only, P-IRIS is changed to maximum open due to the securing of light intensity at night
shift.)

•

Image Appearance

This provides access to the advanced image settings for the network camera.

–

Brightness: The image brightness can be adjusted in the range 1-10, where a higher

value produces a brighter image.

–

Contrast: Adjust the image’s contrast by raising or lowering the value in this field.

30

–

Saturation: Set an appropriate value in the range 1-10. Lower values mean less color

saturation.

–

Hue: Set an appropriate value in the range 1-10. The value distinguishes color, such as

red, yellow, green, or violet.

–

Sharpness: Set the amount of sharpening applied to the image. A sharper image might

increase image noise especially in low light conditions. A lower setting reduces image
noise, but the image would be less sharp.

–

White Balance Mode: Select white balance mode which fits camera installation

environment. In case of Manual mode, user can set R, G, B gain manually.

•

Enhance Control

–

Enable wide dynamic range: Activates WDR which cannot be used with Defog

function. If WDR is activated, shutter mode becomes automatic only.

–

Enable flip horizontally: Check this box to flip the image.

–

Enable mirror image: Check this box to mirror the image.

–

Enable noise reduction: Check this box to activate the noise reduction.

Once enabled, you can select noise reduction level.

–

Enable defog: Check this box to activate the defog function.

–

Metering Mode: Users can change the metering mode.

* Metering Mode: Method of measuring the intensity of the light hitting and reflected by a

subject in order to determine the exposure required.

•

Day & Night Control

User can setup Day & Night operation mode among Automatic, Day, and Night.

–

Mode:

·

Automatic: Normally displays color image, and switches automatically to black &
white image after the ambient light level reaches a pre-defined thresh- old.

·

Day: Always displays color image.

·

Night: Always displays black & white image.

–

Threshold: Adjusts the level of light which the camera automatically switches

between color and black & white image.

31

–

Smart Focus sync with Day & Night: Focus control automatically adjusts upon

Day/Night change. (This menu appears for motorized lens model only.)

•

IR Control
User can enable/disable built-in IR LED and

–

IR Type:

·

Static IR: When switching to Night, IR is ON with the set value.

• Max Strength: Users can specify the intensity of the IR to prevent
saturation of the image.

·

Smart IR: This function adjusts IR for appropriate brightness if it is dark even using
the set Gain at Night switching,

·

Speed: Users can adjust the control speed of the smart IR.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

32

6)

OSD

This camera provides two OSD’s (on screen display) on each stream, title and date & time. User
can drag green “OSD Title” and “Date & Time” to the desired position and check at preview
window.

•

Video Preview: User can check the position of OSD on actual video via preview pop- up
window.

•

OSD Setting: User can select to show or hide OSD for each stream. Also user can set the
transparency level of OSD by slide bar or type in number.

•

OSD title: User can show or hide OSD title, and can change OSD title by type in. The default
is the model name of the camera.

•

OSD subtitle: User can show or hide OSD subtitle, and can change OSD subtitle by type in.
The default is the Subtitle 1.

•

Date & Time: User can show or hide date & time on OSD.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

33

3.6.3 Audio

The network camera can transmit audio to other clients using an external microphone and can play
audio received from other clients by attaching a speaker. The Setup page has an additional menu
item called Audio, which allows different audio configurations, such as full duplex and simplex.

•

Audio Setting:

–

Enable audio: Check the box to enable audio in the video stream.

–

Compression type: G.711 µ-law

–

Sample rate: 8KHz

–

Sound bit rate: 64Kbps

•

Audio Input: Audio from an external line source can be connected to the STEREO Jack
I/O of the network camera.

–

Input volume: If there are problems with the sound input being too low or high, it is

possible to adjust the input gain for the microphone attached to the network camera.

–

Mute: User can disable the input audio transmission by checking the box.

•

Audio Output:

–

Enable full duplex: Check the box to enable Full Duplex mode. This means that

you can transmit and receive audio (talk and listen) at the same time, without having to
use any of the controls. This is just like having a telephone conversation. This mode

requires that the client PC has a sound card with support for full-duplex audio.
Uncheck the box enable Simplex mode. The simplex mode only transmits audio from the
network camera to any web client. It does not receive audio from other web clients.

34

–

Output volume: If the sound from the speaker is too low or high it is possible to adjust

the output gain for the active speaker attached to the network camera.

–

Mute: User can disable the output audio transmission by checking the box.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

3.6.4 Event



Event In

∇ On Boot

This is used to trigger an event every time the network camera is started.

Select “Enable on boot” to activate the On Boot event.
Enter the Dwell time the event lasts from the point of detection, 1-180 seconds.
When the settings are complete, click Save button to save the settings, or click Reset button to clear

all of the information you entered without saving it.

35

∇ Alarm In

This camera provides 1 Alarm In port and user can set the port. The Port can be given as Normally
Open or Normally Close state, and its Normal state can be configured. In order to use the alarm
port, check the “Enable alarm port 1” first.

•

Type: Choose the type of alarm to use from the drop-down list, NO (Normally Open) or NC
(Normally Closed).

•

Dwell Time: Set the dwell time an event lasts from the point of detection of an alarm input.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

36

∇ Manual Trigger

This option makes use of the manual trigger button provided on the Live View page, which is used
to start or stop the event type manually. Alternatively, the event can be triggered via the product’s
API (Application Programming Interface).

Select “Enable manual trigger” to activate the manual trigger (for up to 4 manual triggers). Set the
dwell time the trigger lasts.
When the settings are complete, click Save button to save the settings, or click Reset button to clear

all of the information you entered without saving it.

37

∇ Motion

This option makes use of the motion detection function with 16 programmable areas, 8
Include and Exclude zones each.
Click right mouse button on the preview window shows selection pop-up of New Motion, New
Mask, Select, Delete, and Freeze.
Select New Motion and click&drag generates an Include box of green color. Select
New Mask and click&drag generates an Exclude box of orange color. Drag corner
or line resizes and drag inside moves the box.
Select “Enable video motion detection” to activate motion detection.

•

Sensitivity: User can change sensitivity of this function, where large value sets more
sensitive detection.

•

Zone List



ID: Order of generation, Include 1∼8, Exclude 9∼16.



Name: User definable zone name.



Type: shows zone type and cannot be changed.



Threshold: Determines how large the motion in the zone can trigger event in
percentage.



Dwell time: Determines how long the triggered event holds from the last triggering.

38



Show Histogram: This camera provides live histogram for easy setup of thresh- old
level in motion window. The pop-up window shows activity strength and threshold
level, and user can determine threshold level for triggering motion event by slide bar or
type in number.

User can select any box by clicking name on the preview window or click on the list. User can
delete selected zone via right mouse click selection for a selected box, or click any one of X button
in the zone list.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

39

∇ Network Loss

This is used to trigger an event every time the network connection is failed.
Select “Enable network loss” to activate the Network Loss event. Select a dwell time for how long the

event will last from the point of detection.
When the settings are complete, click Save button to save the settings, or click Reset button to clear

all of the information you entered without saving it.

40

∇ AIHM

AIHM (Advanced Intelligent Health Monitoring) triggers an event when abnormality of the camera
occurs.

• AIHM Setting: Select “Enable AIHM” to activate the AIHM function.
– Enable record status check: Trigger event if the record status is modified.
– Enable format event: Trigger event if the micro-SD card is formatted.

• AIHM Server Setting: Select “Enable AIHM Server” to activate the AIHM Server function
– Enable AIHM Server: If selected, the message is sent to the AIHM server.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

NOTE: This function may not be applicable, depending on the model.

41

∇ Time Trigger

Time Trigger is to set alarms at specific time. User can set up to four time triggers and each time
trigger can be set to specific date in the calendar, every day, day of the week, or date of every
month.

Select “Enable time trigger” to activate the Time Trigger function.

•

Enable specific time: User can select a date in the calendar or type in date, and specify
time for event trigger.

•

Enable every day: Trigger event every day at specified time.

•

Enable day of week: Trigger event at the day of every week at specified time.

•

Enable month: Trigger event at the date of every month at specified time.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

42

▽ VA

The network cameras provide VA (Video Analysis) functions.

Click the Enable video content analysis check box.
For the PTZ Camera, users can set different VA Event for each preset. Select the Preset number to
apply VA.

NOTE: The VA function is limited to the events that can be used depending on the license type.

43

-

situation

default set image

Recommended

settings

modified set image

Two
objects
are
detected
as one

In this scene, two
objects are detected as
one. This is usually due
to the maximum size of
the object that is not set
correctly. Reduce the
maximum size of the
object.

Generally, when
setting the
minimum and
maximum sizes,
the average size
should be set to
the minimum size
of the object, half
the width and
height of the
object, and the
maximum size of
the object should
be about 130% of
the width and
height of the
average object.

By adjusting the maximum
size, two people are
detected as separate
objects.

One
object is
detected
as two

In this scene, one
object is detected as
two objects. Usually
this is because the
minimum and maximum
sizes are set
incorrectly. Increase
the minimum and
maximum size of the
object.

Generally, when
setting the
minimum and
maximum sizes,
the average size
should be set to
the minimum size
of the object, half
the width and
height of the
object, and the
maximum size of
the object should
be about 130% of
the width and
height of the
average object.

Increasing the minimum
and maximum sizes will
ensure that objects are
accurately detected as
one.

High

Some scenes contain

To minimize the

Users can ignore the noise

Standard Type: Intelligent Motion, Intrusion Detector, Tampering

-

Advanced Type: Intelligent Motion, Intrusion Detector, Tampering, Line Detect, Loitering, Hum
an Detector.

•

View Rule: In setting VA Event, users can select events to be displayed in Video Preview.

•

Object: Users can set Object settings.

- Sensitivity allows users to set the object sensitivity to be detected. If there is a lot of noise
(shaking leaves, etc.) on the screen, lower the Sensitivity.

- Users can set the object size to be detected by Min / Max size adjustment.

- Select Show object size to display the object size set in Video Preview.

NOTE: Object size recommended settings

- Indoor installation (in 10m, based on average height): Sensitivity 80 Min width 2 height 6 Max
width 50 height 60.

- Outdoor installation (in 30m, based on car): Sensitivity 80 Min width 2 height 4 Max width 60
height 50.

44

amount of
noise in
image

large amounts of noise,
which can have an
undesirable effect on
the image analysis
because unwanted
objects are detected in
the image or unwanted
events occur.

noise, reducing
the sensitivity will
only detect visible
objects.

in the image and still
detect the object in the
scene.

NOTE: A malfunction may occur under the following conditions.

- Dark environment.

- Changes in brightness due to lighting variations or clouds.

- When a moving object or facility is engaged or overlapped.

- When directing the camera to a light source (e.g. cars in a tunnel, trains).

- When a shadow occurs.

- When trees and plants are shaking in the wind (If possible, install the camera in a location free

of trees and other plants. If it is inevitable, specify the area as Exclusive Area.).

- Changes of fountain.

- An environment where reflections occur, such as rivers, lakes, glass, windows, mirrors, etc. (If

possible, install the camera in a location where there are no reflective objects. If it is inevitable,
specify the area as Exclusive Area).

- If the object size is less than 5% or more than 40% on the screen.

- When the brightness changes due to AGC or IRIS operation of the camera.

- When an object with a minor difference from its background and brightness moves.

- Bad weather conditions such as typhoon, snow, rain.

- If the object size changes significantly due to movement toward the camera.

- When passing behind an object such as a tree.

- When the movement is feeble.

- When moving at high speed.

- If there are too many moving objects, it is difficult to create a background (for example, a

subway platform at commute time).

- When the image is shaken due to camera shake.

- When there is a flashing light in the shooting area.

- If the camera lens is not clear or out of focus.

• Detection Rule: Set VA Event.

- Select Event in the Select box (default: None). When Event is selected, a menu for setting
Rule Name and Event will be displayed. Users can set Event in Video Preview with on/off
toggle switch.

NOTE: The number of Detection Rule differs depending on License Type.

- Standard Type: 3

- Advanced Type: 8

• How to set up

- Line Detector:

1. Click the None menu to change into Line Detector.

45

2. Enter the Rule Name and select the Line Event type from the Counter menu. The
Detector will generate an event when an object passes over the set line. Counter
sets the direction and generates an event when an object moves in the set direction
and increases the count. To reset the count, click the Reset button.

3. Set direction of line detection in Direction menu.

4. Enable the on / off toggle switch to on and set the line area in Video Preview

- Tampering:

1. Click the None menu to change into Tampering.

2. Enter the Rule Name and set the Dwell time. Tampering generates an event if there
is a scene change. Users can adjust the tampering sensitivity in the Sensitivity menu.

3. In the Light Change menu, users can include lighting on / off as a tampering event.
Users can adjust the sensitivity of Light Change in the Light Sensitivity menu.

- Intelligent Motion:

1. Click the None menu to change into Intelligent Motion.

2. Enter the Rule Name and set the Dwell time. Intelligent Motion generates an event
when motion is detected in the set area. Users can adjust the sensitivity of Intelligent
Motion in the Sensitivity menu.

3. Enable the on / off toggle switch to on and set the Intelligent Motion area in Video
Preview. The Intelligent Motion area is displayed as a blue cell.

NOTE: When Intelligent Motion is enabled, the existing Motion Detection is disabled.

- Intrusion:

1. Click the None menu to change into Intrusion.

2. Enter the Rule Name. Intrusion occurs when an object enters, appears or exits
in/from set area.

3. Enable the on / off toggle switch to on and set the Intrusion area in Video Preview.
The Intrusion area is displayed as a yellow cell.

- Loitering:

1. Click the None menu to change into Loitering.

2. Enter the Rule Name. Loitering generates an event if an object enters a set area and
walks or stays for more than the set time.

3. Enable the on / off toggle switch to on and set the Loitering area in Video Preview.
The Loitering area is displayed as a purple cell.

- Human:

1. Click the None menu to change into Human.

2. Enter the Rule Name. Human generates and event if the detected object is human.

NOTE: Conditions for distinguishing human:

- The object must be 10-20% of the screen size.

- Head and shoulders should be visible and moving.

The camera may not be able to distinguish human in the following situations:

- A person who is sitting, crawling, or lying.

46

- Shooting vertically from the ceiling.

Situation

Default set image

Recommended

settings

Modified set image

Scene with
swaying
trees

This scene involves
many unwanted
movements from the
tree. These movements
can cause unwanted
objects to be detected
during image analysis.

Reduce the
sensitivity to
avoid tree
movement. As an
alternative, users
can set the area
around the tree to
Exclusive Area.

This setting avoids the
detection of tree
movement during the
image analysis.

- When a head is unseen

- A person carrying a big baggage

- A person riding a bicycle

- People moving closer together

- Shown less than a second

• Exclusive Area: Set the area to disable Object detection
By not handling unnecessary areas, users can reduce false alarms and CPU usage.
Only Object-based events are not generated. Motion and Tampering runs irrespective of

Exclusive Area.

- How to set Exclusive Area

1. Enable the on / off toggle switch to on and set the Exclusive Area in Video Preview.

• Video Control: Users can make settings for optimal image analysis.

- Click the Relearn Background button to re-learn the current image as background.

- Use the Scene type menu to select the place where the camera is installed.

- Use the View mode menu to select the angle at which the camera is installed.

NOTE: View mode

- Overhead is generally suitable for counting or detecting a moving direction.

- Angle is suitable for detecting intrusions.

- Horizontal should only be used for home security.

Proper camera installation

The Exclusive Area is displayed as red cells.

47

- Installation height: 2.5m ~ 3.0m

- Installation type: Tilt about 30 degrees horizontally and face downward.

- Object: The object must not be within 3 meters of the camera.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

48



Event Out

∇

SMTP(E-Mail)

The network camera can be configured to send event and error email messages via SMTP (Simple
Mail Transfer Protocol).

•

SMTP (E-Mail) Setting: Select “Enable” to activate the SMTP operation.



Sender: Enter an email address to be used as the sender for all messages sent by the
network camera.



Interval: Represents the time interval of the email notification when events occur
several times.



Aggregate events: Shows the maximum number of emails sent within each interval.



Use Mail Server: Check the box if you are using a mail server to receive event
notification and image email.

·

Mail Server: Enter the host names (or IP addresses) for your mail server.

·

Port: Enter the port number for your mail server.

·

Connection security: Select a connection security type in the drop-down
list: None, StartTLS, SSL.



Enable use(SMTP) authentication: Check the box if your mail server requires
authentication.

·

User name/Password: Enter the User name and Password as provided by your
network administrator or ISP (Internet Service Provider).

·

Login method: Choose a log-in method in the drop-down list: AUTH LOGIN
/ AUTH PLAIN

•

SMTP (E-Mail) Receiver: User can assign up to 8 receivers



Receiver #: Enter an email address.

49

•

SMTP (E-Mail) Test: User can check the SMTP setting via a sample email.



Receiver: Enter an email address and click the Test button to test that the mail servers
are functioning and that the email address is valid.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

∇ FTP & JPEG

When the network camera detects an event, it can record and save images to an FTP server. Images can be sent
as e-mail attachments. Check the “Enable FTP” box to enable the service. This camera can support multiple
FTP servers and user can configure each server settings separately.

•

FTP Setting



Server: Enter the server’s IP address or host name. Note that a DNS server must be
specified in the TCP/IP network settings if using a host name.



Port: Enter the port number used by the FTP server. The default is 21.



Passive mode: Under normal circumstances the network camera simply re­quests the target FTP server to open the data connection. Checking this box issues
a PASV command to the FTP server and establishes a passive FTP connection,
whereby the network camera actively initiates both the FTP control and data
connections to the target server. This is normally desirable if there is a fire- wall
between the camera and the target FTP server.



Remote directory: Specify the path to the directory where the uploaded images will
be stored. If this directory does not already exist on the FTP server, there will be an
error message when uploading.



User name/Password: Provide your log-in information.

·

Anonymous login: Check the box if you want to use anonymous login method and
the server supports it.



Time type: The name of the folder where the uploaded image will be saved can be set
as the date, time, and minute of the event.

50

•

JPEG Setting



Pre-event: A pre-event buffer contains images from the time immediately preceding the
event trigger. These are stored internally in the server. This buffer can be very useful
when checking to see what happened to cause the event trigger. Check the box to
enable the pre-trigger buffer, enter the desired total length in seconds, minutes or
hours, and specify the required image frequency.



Post-event: This function is the counterpart to the pre-trigger buffer described above
and contains images from the time immediately after the trigger. Configure as for pre­event.



Prefix file name: This name will be used for all the image files saved. If suffixes are
also used, the file name will take the form <prefix> <suffix>.<extension>.



Additional suffix: Add either a date/time suffix or a sequence number, with or without
a maximum value.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

∇ Alarm Out

When the network camera detects an event, it can control external equipment connected to its
alarm output port.

•

Enable alarm out: If selected, the output becomes activated for as long as the event is
active.

•

Type: Select a type of NO (Normally Open) or NC (Normally Closed).

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

51

∇ Audio Alert

When the network camera detects an event, it can output a predefined audio data to external speaker.
Check the “Enable audio alert” box to enable the service.

•

Audio Alert Setting
To use the audio alert with the network camera, an audio data file made by user must

be uploaded from your PC. Provide the path to the file directly, or use the Browse button
to locate it. Then click the Upload button. Up to 3 audio files are available. The total file size
must be less than 512 KB.

•

Audio Alert Test
When the setup is complete, the audio output can be tested by clicking the Test button.

To remove an audio file, select the file and click the Remove button.

NOTE: For a proper operation of Audio Alert, full duplex must be enabled in the Audio set- tings
page.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

52

∇ Record

When the network camera detects an event, it can record the video stream onto the Micro SD
Memory (not supplied) or NAS (Network Attached Device) as a storage device. Check
Record” box to enable the service.

•

Record Setting



Overwrite: Click checkbox to overwrite the storage device; Continuous Record is
available when not using an SD card.



Stream Type: You can select Stream 1, Stream 3, or Stream 4.

·

Stream1, 3, 4: H.264 data

Note: Stream2: MJPEG data cannot be recorded.



Pre-event: Enter pre-event time value for the storage device pre-recording.



Post-event: Enter post-event time value for the storage device pre-recording.



Audio Record: Check the box if you want to record audio with video.

•

Record Schedule
You can set the weekly recording schedule for each day. Drag or click area by a box

unit at first. Clicking the block toggles the recording between on and off. Click the All Select
button to set a schedule for the entire week or a whole day, respectively.

the “Enable

•

Device Setting
Select the device type to be recorded in the drop-down list. The screen changes

53

according to selection.



SD: Mounted SD card.



CIFS: A file format for a NAS device.



NFS: A file format for a NAS device.

NOTE 1: Common Internet File System (CIFS) is a remote file access protocol that forms the

basis for Windows file sharing, network printing, and various other network services. CIFS
requires a large number of request/response transactions and its performance degrades
significantly over high-latency WAN links such as the Internet.

NOTE 2: Network File System (NFS) is a network file system protocol, allowing a user on a
client computer to access files over a network in a manner similar to how local storage is
accessed. NFS, like many other protocols, builds on the Open Network Computing Remote
Procedure Call (ONC RPC) system.

The CIFS screen displays as below.

–

Address: Enter IP address for NAS device.

–

Remote Directory: Enter directory or folder location to be recorded in the NAS device.

–

Capacity: Enter the capacity of storage to be used. This must be less than the total

storage capacity.

–

ID/Password: Enter ID and Password. The network camera will ask for these

whenever you access NAS device.

–

Check: Press the Check button to check the validity of Device Setting data.

•

Format: Click the Format button to format SD card.

•

Device Remove: Click the Device Remove button before detaching SD card for data safety
in the SD card.

•

Device Information: Show current SD card information.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

54

∇ XML Notification

When the network camera detects an event, Notification server is used to receive notification
messages as a type of XML data format. Check the box to enable the service.

•

XML Notification Setting:



Notification server URL: The network address to the server and the script that will
handle the request.



Notification server port: The port number of the notification server.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

55

∇ Boost

The Boost feature is used in conjunction with event detection. When this feature is turned ON, the
Frame rate and Bit rate in the boost condition can be set to a different value than the ones in the
normal condition field. When an event is detected, the camera will boost the Frame rate and Bit rate
from the normal condition to this boosted level for the duration of the event.

Check the box to enable the service.

•

Boost Setting: You can set the condition in Normal and Boost mode.



Boot Stream: Select a video stream for each condition in the drop-down list.



Frame rate: Select a frame refresh rate per second for each condition in the drop-
down list.



Bit rate control: Select VBR or CBR in the drop-down list in Normal Condition.
You can’t change it in Boost Condition.



Bit rate: Select a value for each condition in the drop-down list.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

56

∇ Notification Server

When the network camera detects an event, the Notification Server is used to receive up- loaded
image files and/or notification messages. Check the box to enable the service.

•

Notification Server Setting:



Type: User can select message transmission type among HTTP, HTTPS, TCP, and
UTP.



URL: The network address to the server and the script that will handle the request.

For example: http://192.168.12.244/cgi-bin/upload.cgi



Port: The port number of the server.



User name/Password: Provide your log-in information.

•

Notification Server Test: When the setup is complete, the connection can be tested by
clicking the Test button using the contents in “Send message” box.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

57



Event Map

The event map allows you to change the settings and establish a schedule for each event trigger
from the network camera; up to a max. 15 events can be registered.

Click the Add button to make a new event map; a popup window displays as below. To change an
existing event, select that event and click the Modify button; this same window will display and the
information can be changed as required. Selecting an event and clicking Remove deletes the event.

58

•

General: Enter the name for a new event map.

•

Event In: Select an event type in the drop-down list.

•

Event Out:



E-mail: Select the email addresses you want to notify via email that an event has
occurred.



FTP: Select checkbox beside FTP to record and save images to an FTP server when
an event has occurred.



Alarm out: Check this box to enable the alarm out.



Audio Alert: Select an Audio Alert file as the Network Transmitter output when audio
alert event triggered. The Audio Alert file must first be configured on the Event In
page.



XML Notification: It sends XML messages to a Notification server that listens for these.
The destination server must first be configured on the Event In page.



Boost: When an event has occurred, the camera will boost the Frame rate and Bit rate
from the normal condition to this boosted level for the duration of the event. Check the
box to enable the Function.



Record: Record video stream when an event has occurred. The Record option must
first be configured on the Event Out page.
Note: This button disappears if you select AIHM as event in.



Notification Server: It sends notification messages to the notification server that listens
for these. The destination server must first be configured on the Event In page. Enter a
message you want to send.

When the settings are complete, click OK button to save the settings, or click Cancel button to clear
all of the information you entered without saving it.

59

3.6.5 System

1)

Information

You can enter the system information. This page is very useful when you require device
information after installation.

•

Device Name Configuration: Enter the device name.

•

Location Configuration: Enter the location information. You can enter up to four locations.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

60

2)

Security

∇

Users

User access control is enabled by default when the administrator sets the root password on first
access. New users are authorized with user names and passwords, or the administrator can choose
to allow anonymous viewer login to the Live View page, as described below:

•

User Setting: Check the box to enable anonymous viewer login to the network camera without
a user account. When using the user account, users have to log-in at every access.

•

User List Setting: This section shows how to register a user account. Enter a user name
and password to be added, and register them by pressing the Add button. You will see the
pop-up window as below.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

61

∇ HTTPS

For greater security, the network camera can be configured to use HTTPS (Hypertext Transfer
Protocol over SSL (Secure Socket Layer)). Then all communication that would otherwise go via
HTTP will instead go via an encrypted HTTPS connection.

•

HTTPS Connection Policy: Choose the form of connection you wish to use from the drop-
down list for the administrator, Operator and Viewer to enable HTTPS connection (set to
HTTP by default).

–

HTTP

–

HTTPS

–

HTTP & HTTPS

•

Upload Certificate: To use HTTPS for communication with the network camera, an official
certificate issued by a CA (Certificate Authority) must be uploaded from your PC. Provide
the path to the certificate directly, or use the Browse button to locate it. Then click the
Upload button.

Please refer to the home page of your preferred CA for information on where to send the
request. For more information, please see the online help.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

62

∇ IP Filtering

Checking the Enable IP address filtering box enables the IP address filtering function. Up to
256 IP address entries may be specified (a single entry can contain multiple IP ad- dresses).
Click the Add button to add new filtered addresses.

When the IP address filter is enabled, addresses added to the list are set as allowed or denied
addresses. All other IP addresses not in this list will then be allowed or denied access accordingly,
that is, if the addresses in the list are allowed, then all others are denied access, and vice versa. Also
see the online help for more information.

NOTE: Users from IP addresses that will be allowed must also be registered with the appropriate
access rights. This is done from Setup > System > Security > Users.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

63

∇ OpenVPN

OpenVPN is a Virtual Private Network using OpenSSL authentication. User can set the camera
in either Server mode or Client mode.

•

OpenVPN Server Mode

1.

Select Enable openVPN activates mode selection buttons. Choose Server mode, then
Server Mode Configuration appears where you can configure Server Mode Settings.

2.

In Server Mode Configuration, you can setup Protocol type, Port number, LZO
compression usage, and Renegotiation time, as well as download Server certificate file.

–

Choose Protocol type between UDP and TCP, UDP is preferred. Type in Port
number you want to use, default is 1194.

–

Default Renegotiation time is 3600 seconds, and 0 means no verification.

–

“Use LZO compression” determines whether to use cypher compression in
connection or not.

–

CA certificate is the certification file issued by Server for Client setup.

3.

After finishing setup, click Save button and then the camera operates as an Open- VPN
Server.

64

•

OpenVPN Client Mode

1.

Select Enable openVPN activates mode selection buttons. Choose Client mode, then
Client Mode Configuration appears where you can configure Client Mode Settings.

2.

In Client Mode Configuration, you can setup Server URL, Protocol type, Port number,
LZO usage, and Renegotiation time.

–

Server URL sets OpenVPN IP address.

–

Protocol type, Port number, and LZO setting must match Server setting.

–

Default Renegotiation time is 3600 seconds, and 0 means no verification.

–

Upload CA certificate issued by Server.

3.

Select authentication method between User authentication and Machine authen­tication.

–

For Machine authentication, upload client certificate and client key provided by
Server.

–

For User authentication, type in registered ID and Password.

4.

After finishing setup, click Save button and then the camera operates as an Open- VPN
Client.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

65

3)

Date & Time

•

Current Server Time
This displays the current date and time (24h clock). The time can be displayed in 12h
clock format (see below).

•

New Server Time

–

Time zone

Select your time zone from the drop-down list. If you want the server clock to
automatically adjust for daylight savings time, check the box “Automatically adjust for
daylight saving time changes”.

–

Time mode: Select the preferred method to use for setting the time:

·

Synchronize with computer time: Sets the time from the clock on your
computer.

·

Synchronize with NTP Server: The network camera will obtain the time from

an NTP server every 60 minutes.

·

Set manually: Allows you to manually set the time and date.

•

Date & Time Format
Specify the formats for the date and time (12h or 24h) displayed in the video streams.

Select Date & Time format from the drop-down list.

–

Date Format: Specify the date format. YYYY: Year, MM: Month, DD: Day

–

Time Format: Specify the date format. 24 Hours or 12 Hours

NOTE: If using a host name for the NTP server, a DNS server must be configured under TCP/IP

settings.
When the settings are complete, click Save button to save the settings, or click Reset button to clear

all of the information you entered without saving it.

66

4)

Network

∇ Basic

•

IP Address Configuration:

–

Obtain IP address via DHCP: Dynamic Host Configuration Protocol (DHCP) is a

protocol that lets network administrators centrally manage and automate the
assignment of IP addresses on a network. DHCP is enabled by default. Although a
DHCP server is mostly used to set an IP address dynamically, it is also possible to use it
to set a static, known IP address for a particular MAC address. To obtain IP address via
DHCP, check the radio button.

–

Use the following IP address: To use a static IP address for the network camera, check

the radio button and then make the following settings:

·

IP address: Specify a unique IP address for your network camera.

·

Subnet mask: Specify the mask for the subnet the network camera is located
on.

·

Default router: Specify the IP address of the default router (gateway) used for
connecting devices attached to different networks and network segments.

•

IPv6 Address Configuration

Check this “Enable IPv6” box to enable IPv6. Other settings for IPv6 are configured in
the network router.

•

DNS Configuration
DNS (Domain Name Service) provides the translation of host names to IP addresses

on your network. Check the radio button to obtain DNS server via DHCP or set the DNS
server.

67

–

Obtain DNS Server via DHCP: Automatically use the DNS server settings pro- vided

by the DHCP server.

–

Use the following DNS server address to enter the desired DNS server by specifying

the following:

·

Domain name: Enter the domain(s) to search for the host name used by the
network camera. Multiple domains can be separated by semicolons (;).

The host name is always the first part of a Fully Qualified Domain Name, for
example, myserver is the host name in the Fully Qualified Domain Name
myserver.mycompany.com where mycompany.com is the Domain name.

·

DNS servers: Enter the IP addresses of the primary and secondary DNS
servers.

•

Host Name Configuration

–

Host Name: Enter the host name to be used as device information in the client

software or SmartManager.

•

Services

–

HTTP port: Enter a port to receive a service through the HTTP. Default port

number is “80”.

–

HTTPS port: Enter a port to receive a service through the HTTPS. Default port number

is “443”.

–

RTSP port: Enter a port to receive a service through the RTSP. Default port

number is “554”.

•

Link Speed Control

–

LAN Interface: Select the transmission method: Auto/Half-Duplex/Full-Duplex.

–

Link Speed: User can select either 10Mbps or 100Mbps.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

68

∇ DDNS

•

Internet DDNS (Dynamic Domain Name Service)
When using the high-speed Internet with the telephone or cable network, users can

operate the network camera on the floating IP environment in which IPs are changed at
every access. Users should receive an account and password by visiting a DDNS service
like http://www.dyndns.com/.

–

Enable DDNS: Check to have DDNS service available.

·

DDNS Server: Select the DDNS server.

·

Registered host: Enter an address of the DDNS server.

·

Username: Enter an ID to access to the DDNS server.

·

Password: Enter a password to be used for accessing the DDNS server.

·

Confirm: Enter the password again to confirm it.

·

Maximum time interval: Set a time interval to synchronize with the DDNS
server. Select the time interval from the drop-down list.

·

Register local network IP address: Register a Network Video Server IP
address to the DDNS server by checking the box and enter the Registered IP

address.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

69

∇

RTP

Create a setting for sending and receiving an audio or video on a real-time basis. These settings
are the IP address, port number, and Time-To -Live value (TTL) to use for the media stream(s) in
multicast H.264 format. Only certain IP addresses and port numbers should be used for multicast
streams.

•

Port Range

–

Start/End port: Enter a value between 1024 and 65532

•

Multicast (Stream1/Stream2/Stream3/Audio/Meta)
This function is for sending Video and Meta Data to Multicast group.

–

Enable Multicast: Check the box to enable multicast operation.

–

Multicast destination IP: Enter an IP between 224.0.0.0 and 239.255.255.255.

–

RTP port: Enter a value between 1024 and 65532.

–

RTP TTL: Enter a value between 1 and 255. If a network status is smooth, enter a

lower value. However, if a network status is poor, enter a higher value. When there are

70

many network cameras or users, a higher value may cause a heavy load to the network.
Consult with a network manager for detailed information.

–

Always enable multicast: Check the box to start multicast streaming without

opening an RTSP session.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

∇ UPnP

The network camera includes support for UPnP. UPnP is enabled by default, so the network camera
is automatically detected by operating systems and clients that support this protocol. Enter a name in
the Friendly name field.

NOTE: UPnP must be installed on your workstation if running Windows XP. To do this, open
the Control Panel from the Start Menu and select Add/Remove Programs. Select Add/Remove
Windows Components and open the Networking Services section. Click De- tails and then select
UPnP as the service to add.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

71

∇ QoS

Quality of Service (QoS) provides the means to guarantee a certain level of a specified re- source
to selected traffic on a network. Quality can be defined as a maintained level of bandwidth, low
latency, and no packet losses.

The main benefits of a QoS-aware network are:

1.

The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser
priority.

2.

Greater reliability in the network, due to the control of the amount of bandwidth an
application may use, and thus control over bandwidth races between applications.

•

DSCP Settings
For each type of network traffic supported by your network video product, enter a DSCP

(Differentiated Services Code Point) value. This value is used to mark the traffics IP header.
When the marked traffic reaches a network router or switch, the DSCP value in the IP
header tells the router or switch which type of treatment to apply to this type of traffic, for
example, how much bandwidth to reserve for it. Note that DSCP values can be entered in
decimal or hex form, but saved values are always shown in decimal. The following types of
traffic are marked; enter a value for each type of traffic used:

–

Live Stream DSCP

–

Event/Alarm DSCP

–

Management DSCP

•

Automatic Traffic Control
Check the box to enable automatic traffic control. Set a limitation on user network

resources by designating the maximum bandwidth. Select either the Maximum band- width
or Automatic framerate radio button.

–

Maximum bandwidth: When sharing other network programs or equipment, it is

possible to set a limitation on the maximum bandwidth in the unit of Mbit/s.

72

–

Priority: When the maximum bandwidth is exceeded, prioritize the data to be reduced.

When the settings are complete, click Save button to save the settings, or click Reset button to clear all
of the information you entered without saving it.

∇ NAT (Port Mapping)

•

NOTES:

•

•

•

•

Wire NAT traversal Settings

–

Enable: Check this box to enable NAT traversal. When enabled, the network camera

attempts to configure port mapping in a NAT router on your network, using UPnP. Note
that UPnP must be enabled in the network camera (see System > Network > UPnP).

·

Automatic setting: When selected, the network camera automatically searches for
NAT routers on your network.

·

Manual setting: Select this option to manually select a NAT router and enter
the external port number for the router in the field provided.

If you attempt to manually enter a port that is already in use, an alert message will be
displayed.

When the port is selected automatically it is displayed in this field. To change this enter a new
port number and click Save.

For NAT (port mapping) to work, this must be supported by the broadband router.
The broadband router has many different names: “NAT router,” “Network router,” “Inter- net

Gateway,” “Broadband sharing device” or ”Home firewall,” but the essential purpose of the
device is the same.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

73

∇

Zeroconf

Zero configuration networking (zeroconf) is a set of techniques that automatically creates a usable
Internet Protocol (IP) network without manual operator intervention or special configuration servers.

Zero configuration networking allows devices such as computers and printers to connect to a
network automatically. Without zeroconf, a network administrator must set up services, such as
Dynamic Host Configuration Protocol (DHCP) and Domain Name System (DNS), or configure
each computer’s network settings manually, which may be difficult and time- consuming.

Zeroconf is built on three core technologies:

•

Assignment of numeric network addresses for networked devices (link-local address auto
configuration)

•

Automatic resolution and distribution of computer hostnames (multicast DNS)

•

Automatic location of network services, such as printing devices through DNS service
discovery.

Click the checkbox to enable Zeroconf.
When the settings are complete, click Save button to save the settings, or click Reset button to clear

all of the information you entered without saving it.

74

∇ Bonjour

The network camera includes support for Bonjour. When enabled, the network camera is
automatically detected by operating systems and clients that support this protocol.

Click the check box to enable Bonjour. Enter a name in the Friendly name field.
NOTE: Also known as zero-configuration networking, Bonjour enables devices to automatically

discover each other on a network, without having to enter IP addresses or configure DNS servers.
(Bonjour is a trademark of Apple Computer, Inc.)

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

75

5)

Language

Select a user language. The language choices are English, Korean, French, German, Russian and
Chinese.

When the settings are complete, click Save button to save the settings, or click Reset button to clear
all of the information you entered without saving it.

76

6)

Maintenance

•

Maintenance:

–

Restart: The unit is restarted without changing any of the settings. Use this method

if the unit is not behaving as expected.

–

Reset: The unit is restarted and most current settings are reset to factory default

values. The settings that are not affected are:

·

the boot protocol (DHCP or static)

·

the static IP address

·

the default router

·

the subnet mask

·

the system time

–

Default: The Default button should be used with caution. Pressing this will return all of

the network camera’s settings to the factory default values (including the IP address).

•

Cloud upgrade: Upgrade your camera by importing an upgrade file from cloud server. Click
Version Check to check upgrade file and pressing the Cloud upgrade button. During the

upgrade, do not turn off the power of the network camera. Wait at least five minutes and then
try to access the camera again.

•

Upgrade: Upgrade your camera by importing an upgrade file from PC and pressing the
Upgrade button. During the upgrade, do not turn off the power of the network camera. Wait

at least five minutes and then try to access the camera again.

77

•

Backup: Save the setting values that users have entered to the network camera to a user
PC.

•

Restore: Import and apply a setting value previously saved to a user PC.

•

IV License: Import and apply Intelligent Video analytics license file.

NOTE: Backup and Restore can only be used on the same unit running the same firmware. This

feature is not intended for multi-configurations or for firmware upgrades.

78

7)

Support

The support page provides valuable information on troubleshooting and contact information, should
you require technical assistance.

•

Log Search: The network camera supports system and event log information. Click the log

Search button to search the Access, Event, Setup or Control log data.

•

Reports:

–

Server Report: Click the Server Report button to get the important information about

the server’s status; this should always be included when requesting sup- port.

–

Parameter List: Click the Parameter List button to see the unit’s parameters and their

current settings.

•

Health Check:

–

System Check: Click the System Check button to get the important information about

the cameras system resources. You can see the pop-up window below.

79

–

Media Check: Click the Media Check button to get the information about the

cameras video and audio stream. You can see the pop-up window below.

–

Networks Check: Click the Network Check button to get the information about the cameras

network setting and traffic. You can see the pop-up window below.

80

3.7 Help

The Help information window will be provided as a popup window so that users can open and read
it without needing to log-in. It will offer a description of the setting and Help page so that users can
manipulate the network camera without a reference to the manual.

81

A Appendix

Problems/Symptoms

Possible Causes or Corrective Actions

The camera cannot be ac­cessed by some clients.

If using a proxy server, try disabling the proxy setting in your
browser. Check all cabling and connectors.

The camera works locally,
but not externally.

Check if there are firewall settings that need to be adjusted.
Check if there are router settings that need to be configured.

Poor or intermittent network
connection.

If using a network switch, check that the port on that de­vice uses the same setting for the network connection type
(speed/duplex).

The camera cannot be ac­cessed via a host name.

Check that the host name and DNS server settings are cor­rect.

Not possible to log in.

When HTTPS is enabled, ensure that the correct protocol
(HTTP or HTTPS) is used. When attempting to log in, you may
need to manually type in http or https in the browser’s address
bar.

No image using Refresh
and/or slow updating of im­ages.

If images are very complex, try limiting the number of clients
accessing the camera.

Images only shown in black
& white.

Check the Video & Image setting.
Blurred images.

Refocus the camera.

Poor image quality.

Increased lighting can often improve image quality. Check
that there is sufficient lighting at the monitored location.
Check all image and lighting settings.

Rolling dark bands or flick­ering in image.

Try adjusting the Exposure Control setting under AE and
AWB part.

H.264 or H.265 not displayed
in the

Check that the correct network interface is selected in the
Video & Image/Stream.

Multicast H.264 or H.265
not displayed in the client.

Check with your network administrator that the multicast
addresses used by the camera are valid for your network.
Check that the Enable multicast checkbox are enabled in the
System/Network/RTP tab. Checks with your network
administrator to see if there is a firewall preventing viewing.

Multicast H.264 or H.265
only accessible by local
clients.

Check if your router supports multicasting, or if the router
settings between the client and the server need to be con­figured. The TTL value may need to be increased.

Color saturation is different
in H.264, H.265 and Motion
JPEG.

Modify the settings for your graphics adapter. Please see
the adapter’s documentation for more information.

Video cannot be recorded.

Check that the Micro-SD card is inserted properly.
Check that the Micro-SD card is formatted properly.

A.1

Troubleshooting

Troubleshooting if problems occur, verify the installation of the network camera with the
instructions in this manual and with other operating equipment. Isolate the problem to the specific
piece of equipment in the system and refer to the equipment manual for further information.

82

A.2

The following connection diagram gives an example of how to connect a network camera.

Alarm Connection

A.3

Preventive maintenance allows detection and correction of minor that faults before they be- come
serious and cause equipment failure.

Preventive Maintenance

Every three-month, perform the following maintenance.

1.

Inspect all connection cables for deterioration or other damage.

2.

Clean components with a clean damp cloth.

3.

Verify that all the mounting hardware is secure.

83

A.4

Item

Recommended

Minimum

OS

Micorsoft® Windows 10

(Home, Professional)

Micorsoft® Windows 7(x86, x64)

(Home Premium)

CPU

intel® Core™ i5-6500

intel® Core™ i3-6100

RAM

8GB or Higher

4GB or Higher

VGA

NVIDIA GeForce GTX 960 or

AMD Radeon R9 280X

NVIDIA GeForce GTX 670 or Radeon

HD 7970

HDD

-

-

LAN

Gigabit Ethernet

Gigabit Ethernet

System Requirement for Web Browser

A.5

When setting up your system, it is important to consider how various settings and situations will
affect performance. Some factors affect the amount of bandwidth (the bit rate) required, others can
affect the frame rate, and some affect both. If the load on the CPU reaches its maximum, this will
also affect the frame rate.

The following factors are among the most important to consider:

General Performance Considerations

•

High image resolutions and/or lower compression levels (or high bitrates) result in larger
images. Frame rate and Bandwidth affected.

•

Accessing both Motion JPEG and H.264 video streams simultaneously. Frame rate and
bandwidth affected.

•

Heavy network utilization due to poor infrastructure. Frame rate and Bandwidth affected.

•

Heavy network utilization via wireless router due to poor infrastructure. Frame rate and
bandwidth affected.

•

Viewing on poorly performing client PCs lowers perceived performance. Frame rate affected.

84

Model

2MP Fixed Lens

2MP MVF Lens

4MP Fixed Lens

4MP MVF Lens

Lens

2.8mm F2.0

3.7mm F2.5

MVF 2.8~12mm,

F1.6, P-Iris

2.8mm F2.0

3.6mm F2.0

MVF 2.8~12mm,

F1.6, P-Iris

Angle of View

2.8mm- 116°(H)

3.7mm - 89°(H)

100° ~ 33°(H)

2.8mm- 108°(H)

3.6mm - 81°(H)

97° ~ 31°(H)

Image Sensor

1/2.8” Sony STARVIS CMOS

1/3” CMOS Sensor

Min. Illumination

Color: 0.03Lux@F1.6

BW: 0Lux@F1.6(IR LED On)

Color: 0.14Lux@F1.6

BW: 0Lux@F1.6(IR LED On)

Scanning Mode

Progressive Scan

Wide Dynamic Range

True WDR

Day and Night Mode

True D/N (Auto, Day, Night)

Noise Reduction

2DNR, 3DNR

Digital Zoom

Yes(ROI)

Exposure Control

Auto

White Balance Control

Auto, Manual

Metering Mode

Spot, Center, Average, Left, Right, Bottom

Image Effect

Flip, Mirror, Defog

Flicker Free Mode

50, 60Hz

Shutter Speed

Auto(1/10,000 ~ 1sec), Manual

IR

Illuminator

Quantity

28 IR LEDs

Distance

Up to 25m

Up to 30m

Up to 25m

Up to 30m

Motorized Lens Control

-

Smart focus, Manual

-

Smart focus,

Manual

VIDEO/AUDIO

Compression

H.264(Baseline, Main, High Profile), H.265(Main Profile), MJPEG

Bitrate Control

CBR, CVBR

Resolution

1920x1080, 1440x1080, 1280x1024/720,

1024x768, 800x600/480, D1, 640x480,

400x240, CIF

2592x1520, 2560x1440, 2304x1296,

1920x1080, 1440x1080, 1280x1024/720,

1024x768, 800x600/480, D1, 640x480,

400x240, CIF

Frame Rate

Max. 25/30fps(PAL/NTSC)

Streaming

Quad Stream(H.264/H.265x3, MJPEGx1)

Composite Out

Yes

Audio Compression

G.711

Audio Streaming

2 Way

SYSTEM

Video Contents Analysis

Tampering, Intelligent Motion, Intrusion detector

Advanced VCA(Option)

Line Detector, Object Counting, Loitering, Human Detector.

Motion Detection Area

16 Programmable Area (Include Area 8, Exclude Area 8)

Privacy Mask Zone

8 Programmable Zone

Smart Codec

Hi-Stream

FTP Uploading

MJPEG

Event Notification

E-mail, FTP, Notification Server, XML Notification, Audio Alert

Audio Alert

User-Defined 3 Audio files

Login Authority

Administrator, Operator, Guest

Event
Buffering

FTP

Pre: 30sec, Post: 30sec

SD Record

Pre: 10sec, Post: 60sec

A.6

Product Specification

VP DOME NETWORK CAMERA

85

Manual Trigger

4 Programmable Trigger

Security

Multi User Authority, IP Filtering, HTTPS, SSL

Network Time Sync

NTP Server, Synchronized Computer, Manual

Software Reset

Restart, Reset, Factory Default

Hardware Factory Reset

Yes

Auto Recovery

Backup, Restore

Remote Upgrade

Web Browsing(IE, Chrome, Safari, Firefox), SmartManager

SD Recording Mode

Event, Continuous

NETWORK

Protocols

TCP/IP, UDP, IPv4/v6, HTTP, HTTPS, QoS, FTP, UPnP, RTP, RTSP, RTCP, DHCP,

ARP, Zeroconf, Bonjour

Client Software

Web, SmartManager, Client S/W

Max. User Connection

10 Users

API Support

Open API, ONVIF Compliance

EXTERNAL IN/OUT

Composite video out

3pin connector

Audio

1 Input, 1 Output (Terminal Block)

Alarm

1 Input, 1 Output (Terminal Block)

Ethernet

RJ-45(10/100Base-T)

u-SD Card

SDHC, SDXC

ETC

Operating Humidity

0 ~ 90% RH(Non-condensing)

Operating Temperature

-20°C ~ 50°C

Power Supply

PoE(IEEE802.3af compliance, Class0), DC12V

Power Consumption

200mA (9.6W)@PoE / 710mA (7.6W)@12VDC

Dimensions

144mm(Φ) x 99mm(H)

Net Weight

Approx. 790g

Approx. 810g

Approx. 790g

Approx. 810g

Ingress Protection

IP66

※ Specifications are subject to change without notice.

Model

4K

Lens

MVF 3.6 ~ 11mm, F1.5, P-Iris

Angle of View

87° ~ 38°(H)

Image Sensor

1/2.5” Sony STARVIS CMOS

Min. Illumination

Color : 0.03Lux @ F1.5

BW : 0Lux @ IR LED On

Scanning Mode

Progressive Scan

Wide Dynamic Range

True WDR

Day and Night Mode

True D/N (Auto, Day, Night)

Noise Reduction

2DNR, 3DNR

Digital Zoom

Yes(ROI)

Exposure Control

Auto

White Balance Control

Auto, Manual

Metering Mode

Spot, Center, Average, Left, Right, Bottom

Image Effect

Flip, Mirror, Defog

Flicker Free Mode

50, 60Hz

Shutter Speed

Auto(1/10,000 ~ 1sec), Manual

IR

Illuminator

Quantity

28 IR LEDs

Distance

Up to 30M

Motorized Lens Control

Smart focus, Manual

VIDEO/AUDIO

Compression

H.264(Baseline, Main, High Profile), H.265(Main Profile), MJPEG

Bitrate Control

CBR, CVBR

Resolution

3840x2160, 3072×2048, 2592x1944/1520, 2560x1440, 1920x1080, 1440x1080,

1280x1024/720, 1024x768, 800x600/480, D1, 640x480, 400x240, CIF

Frame Rate

Max. 25/30fps(PAL/NTSC)

Streaming

Quad Stream(H.264/H.265x3, MJPEGx1)

Audio Compression

G.711

Audio Streaming

2 Way

SYSTEM

Video Contents Analysis

Tampering, Intelligent Motion, Intrusion Detector

Advanced VCA(Option)

Line Detector, Object Counting, Loitering, Human Detector.

Motion Detection Area

16 Programmable Area (Include Area 8, Exclude Area 8)

Privacy Mask Zone

8 Programmable Zone

Smart Codec

Hi-Stream

FTP Uploading

MJPEG

Event Notification

E-mail, FTP, Notification Server, XML Notification, Audio Alert

Audio Alert

User-Defined 3 Audio files

Login Authority

Administrator, Operator, Guest

Event
Buffering

FTP

Pre: 30sec, Post: 30sec

SD Record

Pre: 10sec, Post: 60sec

Manual Trigger

4 Programmable Trigger

Security

Multi User Authority, IP Filtering, HTTPS, SSL

Network Time Sync

NTP Server, Synchronized Computer, Manual

Software Reset

Restart, Reset, Factory Default

Hardware Factory Reset

Yes

Auto Recovery

Backup, Restore

Remote Upgrade

Web Browsing(IE, Chrome, Safari, Firefox), SmartManager

SD Recording Mode

Event, Continuous

NETWORK

Protocols

TCP/IP, UDP, IPv4/v6, HTTP, HTTPS, QoS, FTP, UPnP, RTP, RTSP, RTCP, DHCP,

ARP, Zeroconf, Bonjour

Client Software

Web, SmartManager, Client S/W

Max. User Connection

10 Users

API Support

Open API, ONVIF Compliance

EXTERNAL IN/OUT

Composite video out

3Pin Connector

Audio

1 Input, 1 Output (Terminal Block)

Alarm

1 Input, 1 Output (Terminal Block)

Ethernet

RJ-45(10/100/1000 Base-T)

u-SD Card

SDHC/SDXC

ETC

Operating Humidity

0 ~ 90% RH(Non-condensing)

Operating Temperature

-20°C ~ 50°C

Power Supply

PoE(IEEE802.3af compliance, Class0), 12VDC

Power Consumption

200mA (9.6W)@PoE / 710mA (7.6W)@12VDC

Dimensions

144mm(Φ) x 98mm(H)

Net Weight

Approx. 785g

Ingress Protection

IP66

※ Specifications are subject to change without notice.

VP DOME NETWORK CAMERA

Rev.A