AT&T Disk, Wall, Trimline Single Line Business Telephone Owner's Manual

AT&T

CAUTION

SINGLE LINE

BUSINESS

TELEPHONES

DESK, WALL AND

TRIMLINE® MODELS

ISSUE 3

APRIL 1986

403683022

999-500-270-IS

950-270-IS

INTRODUCTION

JACK
OPENING

This booklet contains installation and
removal instructions for standard modular
desk or wall telephones.

Jack For Wall Telephone

Figure 1.

Standard Modular Telephone
Jacks

If you do not have a standard modular
telephone jack, contact your local
telephone company or AT&T Information
Systems for details on converting your
present outlet to a modular jack.

INSTALLATION

Your telephone is fully assembled except
for the coiled handset cord and clear line
cord.

To Install Your Desk Or Trimline®
Telephone

Installation of the following options requires
a professional installer.

Adjunct Dialer
SPOKESMAN® Loudspeaker

External Speakerphone
Headset Adapter

Contact your place of purchase for details.

Package Content

HANDSET

Make sure your package contains the
following items:

BASE

●

●

●

●

●

●

●

●

●

Telephone
Handset
Handset cord
Line cord

Plug one end of the coiled handset cord
into the opening in the handset. Push

the plug in until it clicks. (Figure 2)
Plug the other end of the cord into the

side opening in the base. Push the plug
in until it clicks.

Plug one end of the clear line cord into

1.

2.

3.

Number card

Modular Outlet Requirement

You must have a standard modular
telephone jack, such as one of those
shown below, to install your phone. If you
have one of these jacks already mounted,
no tools are needed.

COILED HANDSET CORD

the jack in the base of the telephone.
Push the plug in until it clicks.

Figure 3. Setting the Ringer Volume
Control (Desk and Trimline Telephones)

Plug the other end of the cord into the
telephone jack in your office. Push the

JACK

CLEAR

LINE

CORD

OR

JACK

JACK

HANDSET

COILED

HANDSET

CORD

plug in until it clicks.
Turn your telephone over or for Trimline

telephones, lift the handset. (Figure 3)
Set the ringer volume switch or

4.

5.

6.

1.

thumbwheel to the setting you want.

To Install Your Wall Telephone

Align the wall phone plug with the jack,
then line up the hole in the back of the
telephone set with the rivets on the wall
outlet plate. Push in and slide the
telephone down into place. (Figure 4)

JACK OPENING

JACK OPENING

Jacks for Desk or Trimline® Telephones

Figure 2. Desk Telephone Installation

INTRODUCTION

JACK
OPENING

Jack For Wall Telephone

Figure 1.

Standard Modular Telephone
Jacks

If you do not have a standard modular
telephone jack, contact your local
telephone company or AT&T Information
Systems for details on converting your
present outlet to a modular jack.

INSTALLATION

Your telephone is fully assembled except
for the coiled handset cord and clear line
cord.

To Install Your Desk Or Trimline®
Telephone

Package Content

HANDSET

BASE

Plug one end of the coiled handset cord
into the opening in the handset. Push

the plug in until it clicks. (Figure 2)
Plug the other end of the cord into the

side opening in the base. Push the plug
in until it clicks.

Plug one end of the clear line cord into

1.

2.

3.

COILED HANDSET CORD

the jack in the base of the telephone.
Push the plug in until it clicks.

Figure 3. Setting the Ringer Volume
Control (Desk and Trimline Telephones)

Plug the other end of the cord into the
telephone jack in your office. Push the

JACK

CLEAR

LINE

CORD

OR

JACK

JACK

HANDSET

COILED

HANDSET

CORD

plug in until it clicks.
Turn your telephone over or for Trimline

telephones, lift the handset. (Figure 3)
Set the ringer volume switch or

4.

5.

6.

1.

thumbwheel to the setting you want.

To Install Your Wall Telephone

Align the wall phone plug with the jack,
then line up the hole in the back of the
telephone set with the rivets on the wall
outlet plate. Push in and slide the
telephone down into place. (Figure 4)

JACK OPENING

Figure 2. Desk Telephone Installation