AT&T MLC-5, MERLIN LEGEND Release 2.0 MLC-5 Cordless Supplementary Manual
MERLIN LEGEND™
Communications System
Release 2.0
MLC-5™ Cordless Telephone Quick Reference
System Speed Dialing
Account Codes
List Most Often Used-Codes
List Most Often-Codes
Name
Code
Name
Code
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
15.
16.
17.
Posted Messages
1. Do Not Disturb
6.
11.
16.
2.
7.
12.
17.
3. 8.
13.
18.
4.
9.
14.
19.
5.
10.
15.
20.
AT&T CIC# 555-620-128
Issue 1- October 1992
TELEPHONE
MLC-5 Cordless Telephone Handset
Imprinted Buttons
Button
Labeling
Card
Channel
Button
Line
Buttons
Low
Battery
Light
Message
Light
Card used to note
feature or line assigned
to each line button.
Button used to change
channels for improved
reception.
Five buttons with red
lights, used to make/
receive calls. Any
unlabeled buttons can
be programmed with
features.
Light blinks when
batteries have less than
15 minutes of use
remaining (tone also
generated).
Light illuminates
when you have a voice-
mail message, fax, or a
message from the
Imprinted buttons, including dedicated
feature buttons, cannot be changed.
Hold
Status
Transfer
Channel
system operator.
On/Off
MLC-5 Cordless Telephone Base Unit
Antenna
Battery
Contacts
Channel
Indicator
Directory
Card
Message
Light
Retractable antenna;
extend fully for clear
reception.
Mode
Metal contacts that
Lights
recharge the handset.
Clean contacts
periodically with a soft
pencil eraser.
Electronic display of
the channel currently
used or programmed.
A "P" displays when
the telephone is being
programmed.
Erasable card used to
record the telephone
number assigned to the
cordless telephone and
to list feature codes.
Light illuminates when
you have a voice-mail
message, fax, or
message from the
system operator.
Ringing
Volume
Control
●
●
●
Press to put a call on hold.
Red light flashes while call
is on hold. During hold,
phone beeps every 60
seconds. More than one
call can be on hold at a
time.
Press to show on the
status of the handset line
button lights, except for
On/Off, Low Battery,
and
Message. Light turns
off after 20 seconds.
Press to send a call to
another phone.
Press to change the
channel to improve
reception.
Press to activate the
handset to make or
answer a call.
Charge
- a light that
illuminates when the
handset is in the the base
unit and the batteries are
charging.
Talk
- a light that
illuminates when the
handset is removed from
the base unit and, is turned
on using On/Off button.
Program
- a light that
illuminates when the T/P
switch is set to P for
programming.
Sliding control used to
adjust the volume of the
base unit’s ring.
Switch used to test and
program the telephone.
T/P
Switch
CALL HANDLING
Line Button Lights
Light
Meaning
Rings
Ring
Meaning
Steady red
The line or the feature
programmed onto the line
button is in use.
Flashing red
An incoming call is ringing
on this button.
Fast flashing
You have put a call on hold
red
on this line button.
Slow flashing
Someone else has put a
call red on hold on this line button.
Tones
Tone
Meaning
Dial tone
You can make a call.
(steady tone)
Busy (slow
The phone you are calling
repeating tone)
is busy.
Fast busy (fast
No lines are available.
repeating tone)
Alternating high
You dialed a number
and low tones
incorrectly or misused
a feature.
Confirmation tone
You used a feature
(double break
properly.
in dial tone
followed by
steady tone)
Callback tone
The outside line or the
five short
extension is busy and your
beeps) phone is programmed for
Automatic Callback.
Call Waiting
You have an inside call
tone (one or (one beep) or an outtwo beeps while
side call (two beeps)
you are on
waiting.
another call)
One long ring
An inside call
One short ring and An outside call
one long ring
Two short rings and
one long ring
Answering Calls
If you are not on the telephone:
● Press On/Off.
After completing the call, press
the On/Off button again or
place the handset on the base
unit.
If you are on the telephone:
1. Press Hold to put the
active call on hold.
2.
Press the button next the
flashing red light to
answer the incoming call.
Return to the held call by
pressing the button next to the
flashing red light.
Making Inside and
Outside Calls
1.
2.
3.
4.
5.
Extend antennas on both the
handset and the base unit.
For outside calls only, press
Status to view which
lines or features are in use.
Press the button for the
available line.
For
SA
buttons, dial the dialout code and telephone
number.
After completing the call,
press On/Off again or
place the handset in the
base unit.
An outside call transferred to you,
a returning transferred call, or a
returning Callback call
Conference
You can participate in a
conference call using an MLC-5
Cordless telephone, but you
cannot use a cordless
telephone
to initiate the conference call.
Transfer
To transfer:
1.
Press Transfer.
2. Press line or SA button.
3.
Dial extensions or number.
4. Announce call, if desired.
5.
Press Transfer, hang up,
or return to call on hold.
To one-touch manual transfer:
1. Press Auto Dial button.
2.
Announce call.
3. Press Transfer, hang up,
or return to call on hold.
To one-touch auto transfer
●
Press Auto Dial button.
Ask your system manager if
this feature is available.
Loading...