AT&T E1802B, E5802B, E1833B, E5833B User Manual

User’s manual

E5802B/E5833B/ E1802B/E1833B

5.8 GHz cordless telephone with caller ID/call waiting

Congratulations

on your purchase

of this AT&T product.

Before using this AT&T product, please

read the Important safety instructions

on pages 41-43 of this manual.

Please thoroughly read the user’s

manual for all the feature operations

and troubleshooting information necessary to install

and operate your new

AT&T product. You can also visit our

website at www.telephones.att.com

Model #: E5802B/E5833B/E1802B/E1833B

Product name: 5.8GHz cordless telephone

Serial #:

(found on the bottom of the telephone base)

Purchase date:

Place of purchase:

You must install and charge the battery before using the telephone.

STOP!

See page 7

for easy instructions.

For customer service or product information, visit our website at www.telephones.att.com.

CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read

and follow these instructions carefully:

• Use only the supplied rechargeable battery or replacement battery 2422 (SKU 23402, part number 89-0047-00-00) or equivalent. To order a replacement battery, visit our website at www.telephones.att. com or call 1 (800) 222-3111; in Canada, call 1 (866) 288-4268.

• Do not dispose of the battery in a fire. Like other batteries of this type, it could explode if burned. Check with local codes for special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

• Exercise care in handling batteries in order not to create a short circuit. Do not allow conductive materials such as rings, bracelets, or keys to touch the battery. The battery or conductor may overheat and cause harm.

• Charge the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

• Observe proper polarity orientation between the battery and battery charger.

• Do not disassemble your telephone. There are no user-serviceable parts inside. Refer to qualified service personnel for servicing.

User’s manual

E5802B/E5833B/ E1802B/E1833B

5.8 GHz cordless

telephone with caller ID/call waiting

Table of contents

Getting started

Quick reference guide .........................2

Parts checklist .........................................4

Telephone base installation .............5

Battery installation & charging ......7

Installation options ...............................8

Belt clip & optional headset .........10

Telephone operation

Settings ....................................................11

Basic operation ....................................14

Options while on calls .....................17

Call transfer for E5802B/E1802B ...18

Call transfer for E5833B/E1833B ...19

DIRECTORY

Feature menu

DIRECTORY .............. Page 20

SPEED DIAL ............. Page 21

RINGER ......................Page 12

DATE/TIME ............... Page 12

DIAL MODE ..............Page 11

CLR VOICE MAIL ....Page 13

LANGUAGE .............. Page 11

Using menus

Press

CID/-VOLUME

to scroll through menu items. Press MENU/SEL to select or modify a

highlighted item. Press OFF/CLEAR to cancel an operation,

or exit the menu display.

DIR /VOLUME+

Getting started

Quick reference guide

Telephone base

VOICEMAIL

Flashes when there is new voicemail (requires voicemail service from your local telephone company).

CHARGE/IN USE

On when the cordless handset is properly positioned to charge in the telephone base.

Flashes quickly while an incoming call is ringing. Flashes when one of the handsets is in use.

HANDSET LOCATOR

Press to make handset(s) beep (page 16).

Getting started

Parts checklist

Save your sales receipt and original packaging in case you need to ship your telephone for warranty service.

Check to make sure the telephone package includes the following. The model number of your telephone can be found on the label located on the bottom of the telephone base.

User’s manual

E5802B/E5833B/ E1802B/E1833B

5.8 GHz cordless telephone with caller ID/call waiting

Quick start guide

E5802B/E5833B/ E1802B/E1833B

5.8 GHz cordless telephone with caller ID/call waiting

User's manual Quick start guide

Charger for cordless handset

Battery for cordless handset (2 for E5802B/1802B) (3 for E5833B/1833B)

Cordless handset (2 for E5802B/1802B) (3 for E5833B/1833B)

(2 for E5802B/1802B) (3 for E5833B/1833B)

Telephone base

Battery compartment door

(2 for E5802B/1802B) (3 for E5833B/1833B)

Power adapter for

telephone base

Power adapter for handset

charger (2 for E5802B/1802B) (3 for E5833B/1833B)

Belt clip for cordless

handset (2 for E5802B/1802B) (3 for E5833B/1833B)

Telephone line cord

Getting started

Telephone base installation

Choose a central location close to a telephone jack and a power outlet not connected to a wall switch. The telephone base can be placed on a flat surface or mounted on a standard wall plate. For optimum range and better reception, place the telephone base in a high and open location.

Avoid placing the telephone base too close to:

• Communication devices such as: personal computers, computer routers, television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11) or other cordless telephones.

• Excessive heat sources.

• Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting.

• Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperatures.

• Mechanical vibration or shock such as on top of the washing machine or work bench.

Getting started

Telephone base installation

1. Plug the small end of

the larger power adapter into th e po wer ja ck at the bottom of the telephone base.

5. Plug the other end

of the telephone line cord into a telephone jack.

Telephone line cord

DSL filter (Optional for DSL users, see number four in the note section, below.)

2. Plug one end of the

telephone line cord into the telephone jack at the bottom of the telephone base.

3. Route cords through

slots.

4. Plug the large end of

the larger power adapter into an electrical outlet not controlled by a wall switch.

NOTES:

1. Use only the power cord supplied with this product or equivalent. To order a replacement power cord, visit our website at www.telephones.att.com, or call 1 (800) 222-3111; in Canada, call 1 (866) 288-4268.

2. Be sure to use an electrical outlet not controlled by a wall switch.

3. This power telephone is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

4. If you receive high speed internet through your telephone line (commonly referred to as DSL), and you are experiencing interference during telephone conversations and/or your caller ID features are not functioning properly, install a DSL filter to the telephone line between the telephone base and the telephone wall jack. Contact your DSL service provider for a DSL filter.

Getting started

Battery installation & charging

After installing the battery, you may be able to make or receive short calls. For best performance, place the handsets in the telephone base or charger to charge for 16 hours before use.

You can keep the battery charged by returning the handsets to the telephone base or the charger after use. When the battery is fully depleted, a recharge takes about 12 hours. The average talk time on a fully charged battery is about eight hours, and the standby time is approximately three days. Actual battery life depends on usage conditions and age of battery.

1. Plug the small end of the smaller power adapter into the jack on the underside of the charger, then route the cord through the slot as shown.

6. You may be able to make or receive short calls. For best performance, place the handset in the telephone base or charger to charge for at least 16 hours before first use.

Battery low indicator

Return the handset to the telephone base or charger to recharge when this symbol flashes and the handset beeps or when the handset screen displays NEEDS RECHARGING.

Caution: Use only the supplied rechargeable battery, replacement battery 2422 (SKU 23402, part

number 89-0047-00-00) or equivalent. To order a replacement battery, visit our website at www.telephones.att.com or call 1 (800) 222-3111; in Canada, call 1 (866) 288-4268.

2. Plug the la rge end of the smaller power adapter into an electrical outlet not controlled by a wall switch.

3. Insert the plug as indicated. Be sure to securely insert the plug, making sure matches the color-coded label inside the battery compartment.

BATTERY LOW

-- 1 --

10:08

02/14

NEEDS RECHARGING

then

4. Place the battery and wires inside the compartment.

NOTE: Under normal conditions, the battery should last around one year. This may vary depending on usage.

5. Slide the battery compartment cover up until it clicks.

To replace the battery, press in and downward on the tab of the battery compartment to open the battery compartment cover. Lift out the old ba ttery and disconnect it from the hand set . Follow th e instruc tio ns on this page to install and charge the new battery.

Getting started

Installation options

Tabletop mount Wall mount

Telephone outlet mounting plate with mounting studs

Wall mounting

The telephone base comes with the bracket mounted for tabletop use. If wall mounting is desired, a telephone outlet wall mounting plate with mounting studs is required. This mounting plate with studs may be available for purchase from many hardware or consumer electronics retailers and may require professional installation.

1. To remove the bracket, hold the telephone base in both hands, press the two bracket tabs and lift the bracket away from slots

and .

2. Connect the telephone line cord and power adapter to the jacks on the bottom of the telephone base. Bundle the telephone cord, and secure it with a twist tie before placing it inside the bracket.

Getting started

Installation options

3. To attach the bracket for wall mounting, insert the tabs of the bracket into slots and on the telephone base, then press the other bracket tabs into slots and as shown on the right.

4. Plug the power adapter into an electrical outlet not controlled by a wall switch. Plug the telephone line cord into a telephone wall jack. To mount the telephone on the wall, position the mounting holes and over the telephone outlet mounting studs. Press and slide the bracket down firmly so the telephone is held securely on the telephone outlet mounting studs.

Tabletop mounting

To return the bracket from the wall mount to tabletop position, follow the directions below.

Telephone outlet mounting studs

1. Remove the telephone base from the wall. Unplug the cords from the wall jacks. Remove the bracket from the telephone base.

3. Route cords through slots. Plug the other end of the telephone line cord into a telephone wall jack. Plug the large end of the larger power adapter into an electrical outlet not controlled by a wall switch.

2. Insert the bracket tabs into slots and

on the telephone base, then press the other bracket tabs into slots and .

Getting started

Belt clip & optional headset

Install belt clip as shown below if desired.

Snap belt clip in to notc hes on both sides of handset.

To rele ase belt clip from handset, lift one side of the belt clip out of the notch.

For hands-free telephone conversations, use any industry standard 2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm headset. To order an AT&T 2.5 mm headset, visit our website at www.telephones.att.com or call 1 (800) 222-3111; in Canada, call 1 (866) 288-4268.

Plug 2.5 mm headset into the jack on the side of handset (beneath small rubber cap).

NOTE: If the sound quality of the

headset is not good, try unplugging it, and firmly plugging it in again.

LANGUAGE

DIAL MODE: TONE

Telephone operation

Settings

Language

The default language for the handset screen displays is English. To change the language to Espanol, or Francais:

1. Press MENU/SEL.

2. Press CID or DIR until the screen displays

LANGUAGE

3. Press MENU/SEL to change the current setting.

4. Press CID or DIR to choose among ENGLISH,

FRANCAIS, or ESPANOL.

5. Press MENU/SEL to confirm your selection and

exit.

Choose dial mode

The dial mode defaults to tone. If you do not have touch tone service, you’ll need to change the setting to pulse:

1. Press MENU/SEL.

2. Press CID or DIR until the screen displays

DIAL MODE

: and the current setting.

3. Press MENU/SEL to change the current setting.

4. Press CID or DIR to display TONE or PULSE.

5. Press MENU/SEL to confirm your selection and

exit.

RINGER: 1

Telephone operation

Settings

Each cordless handset operates individually from the other handsets. The ringer sound, ringer volume, date & time, dial mode and language must be programmed separately for each cordless handset. Follow the steps below to program the cordless handset. To stop at any time, press

OFF/CLEAR.

Choose cordless handset ringer sound

1. Press MENU/SEL to begin programming.

2. Press CID or DIR until the screen displays

RINGER:

and the current setting.

3. Press MENU/SEL to change the current setting.

4. Press CID or DIR to display 1, 2, 3, 4 or OFF.

You will hear a sample of each ringer sound.

5. Press MENU/SEL to choose displayed ringer

sound and exit.

DATE/TIME

10:08 02/14

NOTES:

You can choose to set the

1. time manually, or you can allow it to be set automatically with incoming caller ID information. The time will be set automatically only if you subscribe to caller ID service provided by your local telephone company (page 29). Caller ID will not set the year.

NOTE: If you choose OFF, the cordless handset ringer will

be turned off, and the screen will display RINGER OFF and when the cordless handset is idle (not in use). If there are any un-reviewed calls, the screen will display XX MISSED CALLS instead of RINGER OFF and .

Set cordless handset display date and time

1. Press MENU/SEL to begin programming.

2. Press CID or DIR until the screen displays

DATE/TIME

3. Press MENU/SEL to view or set date and time.

4. Press CID or DIR to change the month in the

date and time line at the bottom of the display, then press MENU/SEL.

5. Repeat step four to set day, hour, minute, and AM/PM.

6. Press MENU/SEL to save selection and exit.

RINGER VOL: LOW

NEW VOICE MAIL

10:08

CLR VOICE MAIL

CLEAR? YES

02/14

Telephone operation

Settings

Choose ringer volume setting

1. Press and hold CID or DIR when the cordless handset is idle (not in use). This feature allows you to choose low, med, high ringer volume or turn the ringer off.

2. Press CID or DIR to choose the desired option. You will hear a sample of each ringer volume.

3. Press MENU/SEL to choose blinking ringer volume and exit.

NOTE: If you choose OFF, the handset ringer will be

turned off, and the screen will display RINGER OFF and when the handset is idle (not in use). If there are any unreviewed calls, the screen will display XX MISSED CALLS instead of RINGER OFF and .

Clear voicemail indication

If you subscribe to voicemail services provided by your local telephone company, NEW VOICE MAIL and a icon will appear on the handset display when you have a new voicemail message. The VOICEMAIL light on the telephone base will flash.

Follow the steps on the left to manually remove the NEW VOICE MAIL message, the icon, and turn off the VOICEMAIL light.

This only turns off the displayed NEW VOICE MAIL message, icon and the VOICEMAIL light; it does not delete your voicemail message(s). Use this feature when the telephone indicates there is voicemail when you have none or you have accessed your voicemail from a remote location (while away from home). If there is actually a new voicemail message, your local telephone company will continue to send a signal which will cause the

NEW VOICE MAIL message, the icon and the VOICEMAIL light to turn back on.

NOTE: Telephone company voicemail may alert you to

new messages with a stutter (broken) dial tone. Contact your telephone company for more details.

PHONE ON 00:30

Elapsed time

Telephone operation

Basic operation

Making and answering calls

To answer an incoming call, press or

SPEAKER

make a call, press then dial a number. Press

, or any dial pad key (0-9, * or #). To

PHONE/FLASH

OFF/CLEAR

To predial (preview numbers before dialing), enter numbers first, then press

SPEAKER

to dial. Press CID then

anytime to make corrections when entering numbers.

The screen displays the elapsed time of the current call (in hours, minutes and seconds).

PHONE/FLASH

SPEAKER

to hang up.

PHONE/FLASH

CHAN/DELETE

NOTE: Only one cordless handset can be on a call at a time. If another cordless handset attempts to join a call, its screen will display OTHE R HAN DSET ON and then OR OUT OF RANGE.

SPEAKER 00:49

NOTES:

1. The elapsed time fo rmat is in minutes and seconds

MM:SS until one hour has elapsed, then it will change to hours, minutes and seconds H:MM:SS.

2. Pressing PHONE/FLASH to access service from your local

telephone service provider will not affect the elapsed time. The elapsed time will not be carried over to the other cordless handset on a transferred call.

Hands-free speakerphone calls

To answer a call, press SPEAKER. To make a call, press SPEAKER, then dial a number. During a call press SPEAKER to switch between hands-free speakerphone and normal handset use. Press OFF/CLEAR to hang up.

NOTE: If a headset is plugged into the handset, the

handset speakerphone will be disabled.

+ 38 hidden pages