AT&T DLC-100 User Manual
Digital Life User Guide
ATT-UM-V1.1-201303
Product Number:
ATT-UM-V1.1-201303
©2012, 2013 AT&T Intellectual Proprieties. All rights reserved.
FCC Compliance Statement
FCC Regulations
The following FCC Regulations apply to most, if not all, 915MHz and 433MHz devices:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
FCC Compliance Statement for UL Certification
The following is the FCC Compliance Statement as it applies to UL Certification:
This device complies with FCC Rules and Regulations as Part 15 devices as
well as Industry Canada Rules and Regulations. Operation is subject to the
following two (2) conditions:
• This device may not cause harmful intereference.
• This device must accept any interference received, including
interference that may cause undesired operation.
Digital Life User Manual | Page i of viii ATT-UM-V1.1-201303
Safety Instructions
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for exposure to
radio frequency (RF) energy set by the Federal Communications Commission of the U.S.
Government.
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure
limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal
operation.
Important Information About Radio Devices
The following information is important when installing radio (wireless) devices:
1. AT&T radio controls provide a reliable communications link and fill an important need in
portable wireless signaling. However, there are some limitations which must be
observed.
2. For US installations only: the radios are required to comply with FCC rules and
regulations including FCC part 15 devices. As such, they have limited transmitter power
and therefore limited range.
3. A receiver cannot respond to more than one transmitted signal at a time and may be
blocked by radio signals that occur on or near their operating frequencies regardless of
code settings.
4. Changes or modifications to the device may void FCC compliance
5. Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
6. RF signals can be affected by metal objects including metal doors or large mirrors. Care
should be taken to avoid these objects during installation as they can interfere with
proper operation.
WARNING!
The polarity of the battery must be observed. Improper handling of lithium batteries may result in
heat generation, explosion or fire, which may lead to personal injuries. Replace only with the
same as recommended by the manufacturer. Use of another battery may present a risk of fire or
corrosion.
CAUTION: Batteries should not be recharged, disassembled in heat above 100ºC (212ºF)
or disposed of in fire. Disposal of used batteries must be made in accordance with the waste
recovery and recycling regulations in your area.
Notice to users in California─This Perchlorate warning applies only to Manganese
Dioxide Lithium cells sold or distributed only in California, USA. Percolate Material
special handling may apply. See www.dtsc.gov.hazardouswaste/perchlorate.
Digital Life User Manual | Page ii of viii ATT-UM-V1.1-201303
Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
Power Source Warning
A label on this product indicates the correct power source for this product. Operate this
product only from an electrical outlet with the voltage and frequency indicated on the
product label. If you are uncertain of the type of power supply to your home or business,
consult your service provider or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.
Digital Life User Manual | Page iii of viii ATT-UM-V1.1-201303
Safety Instructions
Ground the Product
Verify the Power Source from the On/Off Power Light
When the on/off power light is not illuminated, the apparatus may still be connected to
the power source. The light may go out when the apparatus is turned off, regardless of
whether it is still plugged into an AC power source.
Eliminate AC Mains Overloads
WARNING! Avoid electric shock and fire hazard! If this product connects to
coaxial cable wiring, be sure the cable system is grounded (earthed).
Grounding provides some protection against voltage surges and built-up
static charges.
WARNING! Avoid electric shock and fire hazard! Do not overload AC mains,
outlets, extension cords, or integral convenience receptacles. For products
that require battery power or other power sources to operate them, refer to
the operating instructions for those products.
Protect from Exposure to Moisture and Foreign Objects
WARNING! Avoid electric shock and fire hazard! Do not expose this product to
dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such
as vases, should not be placed on this apparatus.
WARNING! Avoid electric shock and fire hazard! Unplug this product before
cleaning. Do not use a liquid cleaner or an aerosol cleaner. Do not use a
magnetic/static cleaning device (dust remover) to clean this product.
WARNING! Avoid electric shock and fire hazard! Never push objects through
the openings in this product. Foreign objects can cause electrical shorts that
can result in electric shock or fire.
Service Warnings
WARNING! Avoid electric shock! Do not open the cover of this product.
Opening or removing the cover may expose you to dangerous voltages. If you
open the cover, your warranty will be void. This product contains no userserviceable parts.
Check Product Safety
Upon completion of any service or repairs to this product, the service technician must
perform safety checks to determine that this product is in proper operating condition.
Digital Life User Manual | Page iv of viii ATT-UM-V1.1-201303
Safety Instructions
Protect the Product When Moving It
Always disconnect the power source when moving the apparatus or connecting or
disconnecting cables.
Battery Replacement Warnings
System Test
WARNING: The battery(ies) used in each device may present a fire or chemical
burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C
(212°F) or dispose of in fire. Replace battery(ies) with specified manufacturer
batteries only. Use of another battery(ies) may present a risk of fire or
explosion."
It is recommended that you test your Digital Life System on a weekly basis.
Digital Life User Manual | Page v of viii ATT-UM-V1.1-201303
Contents
Introduction to the Digital Life System ......................................................................................................... 1
About Your AT&T Digital Life System ........................................................................................................ 1
AT&T Digital Life Central Monitoring Centers .......................................................................................... 2
AT&T Digital Life Support .......................................................................................................................... 2
Digital Life Controller Features and Operation ............................................................................................. 3
Digital Life Controller (DLC-100) Features ................................................................................................ 3
Digital Life Controller (DLC-100) Operation .............................................................................................. 4
Replacing the Digital Life Controller (DLC-100) Battery ............................................................................ 5
Keypad Features and Operation ................................................................................................................... 6
Becoming Familiar with your Keypad (SW-ATT-PAD2W) Features ........................................................... 6
Display .............................................................................................................................................. 6
System LIGHTs .................................................................................................................................. 7
Numeric Keypad ............................................................................................................................... 7
Function Buttons .............................................................................................................................. 7
Emergency Buttons .......................................................................................................................... 7
Operating Your Keypad (SW-ATT-PAD2W) ............................................................................................... 7
Ready to Arm ................................................................................................................................... 8
Not Ready to Arm ............................................................................................................................ 8
Arming the System ........................................................................................................................... 9
Disarming the System – Entry Delay .............................................................................................. 12
Disarming the System .................................................................................................................... 13
Alarm Sounding-Cancel Alarm ....................................................................................................... 14
Sending a Fire Emergency Alarm ................................................................................................... 15
Sending an Auxiliary Emergency Alarm ......................................................................................... 16
Sending a Police Emergency Alarm ................................................................................................ 17
Entering Your Duress PIN ...................................................................................................... ......... 18
Keypad Operation Quick Reference ........................................................................................................ 18
Replacing the Keypad (SW-ATT-PAD2W) Batteries ................................................................................ 18
Keypad and Siren Sounds ........................................................................................................................ 19
Priority of Alarm Signaling ...................................................................................................................... 21
Digital Life User Manual | Page vi of viii ATT-UM-V1.1-201303
Contents
Sounding and Displaying Device Trouble Conditions ............................................................................. . 21
Key Fob Features and Operation ................................................................................................................ 23
Key Fob (SW-ATT-FOB) Operation .......................................................................................................... 23
Replacing the Key Fob (SW-ATT-FOB) Batteries ..................................................................................... 24
Digital Life Customer Care Technical Support ............................................................................................ 25
Creating/Changing Your Alarm Panel PIN ............................................................................................... 25
Creating/Changing Your Duress PIN ....................................................................................................... 25
Changing the Entry Delay Timer ............................................................................................................. 25
Changing the Exit Delay Timer ................................................................................................................ 26
Siren Features and Operation ..................................................................................................................... 26
Siren (SW-ATT-SRN) Operation ............................................................................................................... 27
Replacing the Siren (SW-ATT-SRN) Batteries .......................................................................................... 27
Smoke Detector Features and Operation ................................................................................................... 28
Smoke Detector (SW-ATT-SMKT) Operation .......................................................................................... 28
Replacing the Smoke Detector (SW-ATT-SMKT) Batteries ..................................................................... 28
Testing Your Smoke Detector (SW-ATT-SMKT) ....................................................................................... 29
Maintaining the Smoke Detector (SW-ATT-SMKT) ................................................................................. 29
Evacuation Plan ........................................................................................................................................... 30
Avoiding Fire Hazards.............................................................................................................................. 30
What to do in Case of Fire....................................................................................................................... 30
Always be Prepared ................................................................................................................................ 31
Carbon Monoxide Detector Features and Operation ................................................................................. 31
Carbon Monoxide Detector (SW-ATT-CO) Operation ............................................................................. 32
Replacing the Carbon Monoxide Detector (SW-ATT-CO) Batteries ........................................................ 33
Testing the Carbon Monoxide Detector (SW-ATT-CO) ........................................................................... 34
Maintaining the Carbon Monoxide Detector (SW-ATT-CO) ................................................................... 34
Troubleshooting the Carbon Monoxide Detector (SW-ATT-CO) ............................................................ 34
Vanishing Door/Window Sensor Features and Operation ......................................................................... 35
Replacing the Vanishing Door/Window Sensor (SW-ATT-V2) Battery ................................................... 35
Testing the Vanishing Door/Window Sensor (SW-ATT-V2) .................................................................... 35
Digital Life User Manual | Page vii of viii ATT-UM-V1.1-201303
Contents
Recessed Door/Window Sensor Features and Operation .......................................................................... 36
Replacing the Recessed Door/Window Sensor (SW-ATT-RDW) Battery ................................................ 36
Testing the Recessed Door/Window Sensor (SW-ATT-RDW) ................................................................. 37
Glass Break Sensor Features and Operation ............................................................................................... 38
Replacing the Glass Break Sensor (SW-ATT-GB) Batteries ...................................................................... 38
Testing the Glass Break Detector (SW-ATT-GB) ...................................................................................... 39
Motion Sensor Features and Operation ..................................................................................................... 40
Replacing the Motion Sensor (SW-ATT-PIR) Battery .............................................................................. 40
Testing the PIR Motion Sensor (SW-ATT-PIR) ......................................................................................... 41
915MHz Repeater Features and Operation ................................................................................................ 42
Replacing the 915MHz Repeater (SW-ATT-RPTR9) Batteries ................................................................. 43
433MHz Repeater Features and Operation ................................................................................................ 44
Replacing the 433MHz Repeater (SW-ATT-RPTR4) Batteries ................................................................. 44
Takeover Module Features and Operation ................................................................................................. 46
Replacing the Takeover Module (SW-ATT-TAKRF) Batteries .................................................................. 47
CP-01-2010 Supported Features for False Alarm Reduction ...................................................................... 48
Testing Your System .................................................................................................................................... 52
Digital Life System Testing Instructions .................................................................................................. 52
Digital Life User Manual | Page viii of viii ATT-UM-V1.1-201303
Introduction to the Digital Life System
Introduction to the Digital Life System
HANK YOU FOR CHOOSING AT&T DIGITAL LIFE for Life Safety Services.
Our Life Safety Services include UL certified fire and intrusion monitoring
services. These are end-to-end AT&T services and the underlying AT&T
Digital Life Service Architecture includes:
• AT&T Digital Life System which is professionally installed in your home for alarm
detection.
• AT&T Cellular Data Service for alarm reporting.
• AT&T Central Monitoring Centers with dedicated agents for handling alarms and
contacting Emergency Services.
Optionally, AT&T Digital Life also offers Life Style Services, which include a wide range
of home automation and control services. Please go to www.att.com/digitallife to learn
about Digital Life – Life Style Services.
About Your AT&T Digital Life System
Your professionally installed AT&T Digital Life System (DLS) features a Digital Life
Controller (DLC-100), which is typically installed in a closet, utility room or basement.
Digital Life User Manual | Page 1 of 62 ATT-UM-V1.1-201303
Introduction to the Digital Life System
The DLC-100 is a wireless controller that monitors a wide range of devices for the
detection of fire (smoke detectors and CO detectors) and intrusion (door/window
sensors, motion sensors and glass breakage sensors) alarms. Once the DLC-100 is
installed and activated, it constantly monitors smoke detectors and CO detectors and
automatically reports alarms to the AT&T Digital Life Central Monitoring Centers. When
the system is armed, the DLC-100 automatically reports intrusion alarms to the AT&T
Digital Life Central Monitoring Centers.
AT&T Digital Life Central Monitoring Centers
The AT&T Digital Life Central Monitoring Centers are state-of-the-art, 24x7, UL certified
monitoring facilities. The agents are dedicated to handling and processing alarms.
AT&T Digital Life Support
AT&T Digital Life agents are available 24x7 to provide any assistance that you require.
Please call 1-855-288-2727 for immediate assistance and press the appropriate number
when prompted:
• Active Alarm, press (1)
• New Service, press (2)
• Questions About Your Bill, press (3)
• Customer Care Technical Support, press (4)
In addition you can also access www.att.com/digitallife for additional information
concerning your Digital Life System.
Digital Life User Manual | Page 2 of 62 ATT-UM-V1.1-201303
Digital Life Controller Features and Operation
Digital Life Controller Features and Operation
Your Digital Life System comes with a Digital Life Controller (DLC-100) that
communicates with every device within your Digital Life System configuration. Your
Digital Life Technician has installed your DLC-100 in a closet, utility room or basement.
Digital Life Controller (DLC-100) Features
1. AT&T Cellular Data Antenna
2. Antenna for communication with smoke, carbon monoxide and intrusion detection
devices
3. Antenna for communication with keypads and sirens
4. Antenna for communication with smoke, carbon monoxide and intrusion detection
devices
5. Five System Status LIGHTs
6. Battery Compartment Door
Digital Life User Manual | Page 3 of 62 ATT-UM-V1.1-201303
Digital Life Controller Features and Operation
Digital Life Controller (DLC-100) Operation
The five (5) System LIGHTs on the DLC-100 door provide the following at-a-glance
status:
FEATURE OPERATION
AC POWER
BATTERY
SYSTEM
• FLASHING GREEN LIGHT indicates your DLC is
powering up
• GREEN LIGHT indicates DLC is operational
• LIGHT OFF indicates LOCAL POWER FAILURE
NOTE: During LOCAL POWER FAILURE the BATTERY,
SYSTEM and WIRELESS BROADBAND lights will be
FLASHING GREEN. Wireline Broadband data will not be
operating.
• GREEN LIGHT indicates the battery is fully charged
• RED LIGHT indicates the battery needs to be replaced
• LIGHT OFF indicates the battery is dead or there is no
battery
• GREEN LIGHT indicates your system is working
• RED LIGHT indicates your system has a problem
• YELLOW LIGHT indicates your system is in
Maintenance Mode
• YELLOW LIGHT FLASHING then GREEN LIGHT
FLASHING indicates Radio Frequency (RF) jamming is
being detected
Digital Life User Manual | Page 4 of 62 ATT-UM-V1.1-201303
Type of RF Jamming SYSTEM LIGHT Behavior
One-Way Jamming at
DLC-100 Digital Life
Controller Cabinet
Two-Way Jamming at
DLC-100 Digital Life
Controller Cabinet
One-Way Jamming at a
Repeater
Two-Way Jamming at a
Repeater
SYSTEM LIGHT blinks yellow
once, blinks green once then
repeats
SYSTEM LIGHT blinks yellow
once, blinks green twice then
repeats
SYSTEM LIGHT blinks yellow
once, blinks green three (3)
times then repeats
SYSTEM LIGHT blinks yellow
once, blinks green four (4)
times then repeats
Digital Life Controller Features and Operation
FEATURE OPERATION
WIRELESS BROADBAND
WIRELINE BROADBAND
WARNING! If the SYSTEM LIGHT is flashing Yellow and then flashing Green and an
auditory signal is coming from the Digital Life Controller Cabinet (DLC-100), the DLC100 is detecting Radio Frequency (RF) Jamming. Please call 1-855-288-2727 for
Customer Care Technical Support.
• GREEN LIGHT indicates good signal
• RED LIGHT indicates weak or no signal
• GREEN LIGHT indicates data connection
• LIGHT OFF indicates no data connection
Replacing the Digital Life Controller (DLC-100) Battery
CAUTION: Opening the battery compartment door when the system is armed triggers
the transmission of a tamper alarm to the AT&T Digital Life Central Monitoring Center.
Therefore, in order to prevent a false alarm, please ensure that the system is disarmed
prior to opening the battery compartment door to replace the battery.
To replace the battery:
1. Make sure that the system is disarmed before opening the battery compartment
door to replace the battery.
2. Open the battery compartment by inserting a small coin or the blade of a small
flat screwdriver into the slot on the battery compartment screw and rotate onequarter turn to release the door.
3. Connect the RED wire to the positive (+) terminal and the BLACK wire to the
negative (-) terminal.
4. Insert the battery into the battery compartment. Make sure to properly tuck in
battery wires, so they do not get pinched between the door and frame.
Digital Life User Manual | Page 5 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
Keypad Features and Operation
Your Keypad (SW-ATT-PAD2W) enables you to control basic system functions, such as
arming and disarming your Digital Life System. The keypad includes an LCD, which
displays system status information, and features a built-in sounder that annunciates
system status information. It makes predefined “chirp” and “beep” sounds when buttons
are pressed on the keypad or specific events occur. For example, the system can be
configured so the keypad chirps when an entry/exit door is opened and closed. The
keypad annunciates different sounds for fire alarms and intrusion alarms. (See Appendix
A for information concerning the system messages that can appear in the LCD and
Appendix B for the complete list of auditory annunciations).
The Keypad (SW-ATT-PAD2W) is powered by an AC/DC adapter that plugs into an AC
power outlet. It is equipped with batteries that provide 24-hour battery backup under a
local power failure condition. The batteries are customer replaceable.
Becoming Familiar with your Keypad (SW-ATT-PAD2W) Features
Display
The LCD displays the current system state and any changes in system state.
Digital Life User Manual | Page 6 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
System LIGHTs
If the Armed (Red) LIGHT is ON, a LCD message will indicate the status of the
System: Armed-STAY or Armed-AWAY.
If the Ready (Green) LIGHT is ON, the system is ready for arming.
If the Armed (Red) LIGHT is OFF and the Ready (Green) LIGHT is OFF, then the
system is not ready for arming because one or more of the monitored devices, such
a door or window sensor, is not in the closed state
Numeric Keypad
Use the Numeric keypad to enter your Alarm Panel PIN and Duress PIN, to confirm
emergency button selections, and to access system functions.
Function Buttons
You can use the function buttons to select the STAY, AWAY and BYPASS features.
Emergency Buttons
The Emergency Buttons are used to send an emergency alarm directly to AT&T
Digital Life Central Monitoring Center immediately upon being pressed and
confirmed. The Emergency Buttons are functional whether the system is armed or
not armed.
Operating Your Keypad (SW-ATT-PAD2W)
The Keypad (SW-ATT-PAD2W) is used to arm/disarm the system and obtain information
concerning the status of the system. The system has three (3) primary states:
• Ready to Arm – all of the supervised devices are in the closed state
• Not Ready to Arm – one, or more, of the supervised devices is not in the closed
state
• Armed – system is in the Armed – AWAY or Armed – STAY mode
Digital Life User Manual | Page 7 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
Ready to Arm
The system is ready to be armed when the READY (Green) LIGHT is on and no
message is displayed on the LCD.
Not Ready to Arm
The system is not ready to arm because one, or more, of the supervised devices is
not in the closed state.
Afterwards the keypad will display the name of the open state device(s) and cycle
through the device list if there are multiple devices. Each open state device will
display on a separate line
Digital Life User Manual | Page 8 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
Arming the System
Before you can arm your system, all the devices must be closed. If some devices are
currently open, the Ready light will be off. Before you try to arm your system, close
all doors and windows, and make sure no one is present in areas with motion
sensors.
Arming the System-STAY
Press the STAY button to arm the perimeter sensors only. The system starts an
exit delay timer interval. The keypad beeps and the LCD displays “Arming - Exit
Now”. Initially the keypad beeps slowly during the exit delay timer interval and
then chirps fast for the last ten (10) seconds.
If you choose to exit while Arming – STAY, you should exit through the
designated entry/exit door(s) before the exit delay timer interval expires. After the
exit delay timer interval expires, the system is in the Armed-STAY mode. The
ARMED (Red) LIGHT is illuminated and the LCD displays “Armed - STAY”.
When the system is Armed-STAY, if you open a non-designated entry/exit door
or window it will cause an alarm.
NOTE: You may disarm the system during the exit delay timer interval by
entering your four (4) digit Alarm Panel PIN.
Digital Life User Manual | Page 9 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
Arming the System-AWAY
Press the AWAY button to arm all of the sensors, including perimeter and interior
sensors. The system generates an exit delay timer interval. The keypad beeps
and the LCD displays “Arming - Exit Now.” Initially the keypad beeps slowly
during the exit delay timer interval and then chirps fast for the last ten (10)
seconds.
You should exit through the designated entry/exit door(s) before the exit delay
timer interval expires. You may disarm the system during the exit delay timer
interval by entering your four (4) digit Alarm Panel PIN. After the exit delay timer
interval expires, the system is in the Armed—AWAY mode. The ARMED (Red)
LIGHT is illuminated and the LCD displays “Armed - AWAY”.
Digital Life User Manual | Page 10 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
Arming the System- BYPASS
When arming the system for STAY or AWAY, you may get a message indicating
that the system cannot arm because one, or more, sensor is in an opened state,
such as a window and/or door. You may close the open sensor(s) before arming
or utilize the BYPASS feature.
The LCD will display “Press BYPASS to Proceed.”
The identity of the open sensor(s) will appear in the LCD display.
To proceed with arming the system, either close the open sensor(s) or press the
BYPASS button to bypass the sensor(s).
Digital Life User Manual | Page 11 of 62 ATT-UM-V1.1-201303
Keypad Features and Operation
The system will proceed with the Arming STAY/AWAY sequence.
You should exit through the designated entry/exit door(s) before the exit delay
timer interval expires. After the exit delay timer interval expires, the system is in
the Armed-STAY or Armed-AWAY mode. The ARMED (Red) LIGHT is
illuminated and the LCD displays “Armed - STAY” or “Armed –AWAY”. Initially
the keypad beeps slowly during the exit delay timer interval and then chirps fast
for the last ten (10) seconds.
NOTE: You may disarm the system during the exit delay timer interval by
entering your four (4) digit Alarm Panel PIN.
Disarming the System – Entry Delay
When the system is in the Armed-AWAY or Armed-STAY mode and you enter the
residence through a designated entry/exit door, the system generates an entry delay
timer interval and the keypad begins beeping. The entry delay timer interval allows
you to get to the keypad and enter your Alarm Panel PIN before the system sounds
an alarm. Initially the keypad beeps slowly during the entry delay timer interval and
then chirps fast for the last ten (10) seconds and the LCD displays “Alarm – Enter
PIN to Cancel,” as shown:
Digital Life User Manual | Page 12 of 62 ATT-UM-V1.1-201303
Loading...