Page 1
AT&T U-verse® Wi-Fi
Gateway Replacement
selfinstallation
guide
For use with
High Speed Internet
and Voice
Reminder:
·
Your new gateway does not contain a battery backup.
· Battery backup is available for purchase from third party manufacturers and retailers
to keep you connected in the event of a power failure. Visit att.com/batterybackup
for more information.
Get started Total approximate installation time: 20 minutes
These instructions will guide you through the process of replacing your U-verse Wi-Fi Gateway.
In the box:
Wi-Fi Gateway
Power Cord
2 parts
(Pace 5168 WG H SIA and Voice swap gu ide)
06/15
ATT130300855-4
Page 2
1.
Set up
Approximate time: 10 minutes
You will not have Internet or Voice service while you’re replacing your U-verse Wi-Fi Gateway.
A.
· Unplug the battery backup
from existing Wi-Fi Gateway
and electrical outlet
·
Stand new Wi-Fi Gateway
side-by-side with existing
Wi-Fi Gateway
B.
· Transfer one connection at
a time from the existing
Wi-Fi Gateway to new Wi-Fi
Gateway
C.
· Carefully read and remove
yellow power sticker
covering the Power port of
new Wi-Fi Gateway
·
Connect new power cord to
power port of new
Wi-Fi Gateway and into
electrical outlet
Below is a completed setup. Your connections may vary.
2.
Power up
Approximate time: 1–5 minutes
Your Wi-Fi Gateway is now powering up. During this time, the Broadband light will turn
red and the Power light will turn solid green.
Wait up to 5 minutes for the Service indicator light to turn solid green.
During this time (up to 5 minutes), do not unplug the power cord or the green
data cable, as this can permanently damage the Wi-Fi Gateway and significantly
delay your ser vice activation.
If the Service light does not turn solid green or continues to blink after 5 minutes,
see the Need more help? section on the back of this guide.
Lights may vary with setup.
3.
Go Wi-Fi
Approximate time: 1–5 minutes
New Wi-Fi setup:
A. Select only one option to begin the Wi-Fi setup.
Option 1: Connect using PC
·
Connect laptop or PC with an Ethernet cable
to your Wi-Fi Gateway
· Continue to
B
Option 2: Connect using smartphone/tablet
·
Establish a temporary connection using new Wi-Fi
settings located on yellow sticker on new Wi-Fi Gateway
·
Open your device’s Wi-Fi connection settings and
select your Wi-Fi Network Name and enter your Wi-Fi
Password to connect to your network
· Continue to
B
B.
· Open a browser and go to ufix.att.com/restore.
·
Log in to your U-verse account. If you forgot your User ID (primary AT&T email address) and Password,
help can be found on the account log-in screen.
· Follow the onscreen instructions to transfer the existing Wi-Fi settings.
·
Record existing Network Name and Wi-Fi Password on separate yellow sticker from kit.
· Place new yellow sticker over your new Wi-Fi Gateway’s yellow sticker.
NOTE: If Wi-Fi settings did not transfer or to use new Wi-Fi Network Name and Password,
refer to Need more help? section on back page of guide.
NOTE: Any custom settings made for security cameras, game consoles, etc.,
on your original Wi-Fi Gateway will also need to be made on your new Wi-Fi Gateway.
4.
Easy Return
(Refer to return instructions in your kit)
A.
Return your equipment at no cost
to you within 21 days to avoid
$150 charge.
B.
Take original gateway and power
cord to nearest The UPS Store.
Bring your AT&T Account number
located on your packing slip.
Please do not return other devices
(e.g., backup battery, etc.).
C.
UPS will scan your equipment,
provide a receipt, pack, and ship
equipment to AT&T at no cost
to you.
Wall Jack
Electrical
Outlet
Green
Data Cable
B
Gray
Phone
Cable
B
New Power
Cord
C
Yello w
Ethernet Cable
B
Existing Wi-F i Gateway
New Wi-Fi Gateway
Page 3
Need more help?
No TV or Internet service:
Check your connections:
Cables usually make an
audible click when secure.
Check Power: Power light
on the Wi-Fi Gateway should
be green; if not, try another
electrical outlet.
Front View
Green
Light
Check Service light on front
of the Wi-Fi Gateway: If after
5 minutes, the light is red or off,
power down the Wi-Fi Gateway
by holding down red Reset
button for 15 seconds.
Back View
Reset
but
ton
If your existing Wi-Fi settings did not transfer,
you will need to set up a new Wi-Fi Network
Name and Password. To do so, follow these steps:
·
Use settings from new Wi-Fi Gateway
yellow sticker
·
Open your device’s Wi-Fi connection settings,
select your Wi-Fi Network Name and enter
Wi-Fi Password to connect
·
Record and keep your Wi-Fi settings for future
reference when connecting all your Wi-Fi devices
Wi-Fi Gateway Power light is amber: Don’t worry. This is a normal part of the power-up sequence.
No dial tone: Make sure your phone cable is plugged into the Phone Line port on the Wi-Fi Gateway.
Additional assistance: Call 800.288.2020 and ask for “U-verse technical support”.
Additional U-verse information
Manage your account:
Available 24/7, download the myAT&T app at
att.com/myattapp from your mobile device.
Support:
·
For U-verse support, including live chat,
go to att.com/uversesupport
·
Visit att.com/userguides to find this guide
Pace 5168 WG HSIA and Voice swap guide.
¿Habla español?
Por favor visite att.com/uverseguias para ver la informacion
en español. También pueden ver la siguiente guía:
ATT130300855-4
/Pace 5168 WG HSIA and Voice swap guide
para más detalles.
Accessibility Support:
·
Alternate formats now available in Large Print or Braille.
Call 800.288.2020 and request your guide number
(
ATT130300855-4
)
·
Special Needs Equipment:
- Phone: 877.902.6350
- TT Y: 800.772.2889
·
Repair Center:
- Phone: 800.246.8464
- TTY: 800.397.3172
· Accessible Tagged PDF: Visit att.com/userguides
·
Device Compatibility Feature: Compatible with any TTY/TDD
devices with standard phone line
Need more help?
Visit att.com/uversesupport
Call us at 800.288.2020 and ask for “U-verse technical support.”
©2015 AT&T Intellectual Property. http://www.att.com/gen/privacy-policy?pid=2587 All righ ts reserved. AT&T, th e AT&T
logo and all other AT&T marks contained herein are trademarks of AT&T Intellectual Property and/or AT&T affiliated companies.
Loading...