IN 300
CONNECTING:
Rear view of appliance:
1) Auxiliary Input (optional phono or SPDIF) 11) Trigger Output
2) C.D. Input 12) Right Speaker Output (+ & -)
3) Tuner Input 13) Bluetooth receiver
4) DVD Input 14) Coaxial Inputs 1 & 2
5) Tape Input (PLAY) 15) Optical Inputs 1 & 2
6) Tape Output (REC) 16) USB Input (B type): to connect to
7) BY-PASS Input a computer with compatible software
8) Preamp. Outputs (to 1 or 2 power 17) Switch On/Off and general
amplifiers or to a Subwoofer) plug In (with protection fuse)
9) XLR Input – Right channel 18) Left Speaker Output (+ & -)
10) XLR Input – Left channel
DETAILS OF FUNCTIONS:
Front view of appliance:
19) Headphones jack: speakers Outputs are switshed off when a headphone is plugged in
20) ON/OFF knob (by pushing); sources selection (by rotation)
21) Display: shows the selected source (on the left) and volume level (on the right)
22) Knob to put ON, volume and balance setup.
BLUETOOTH:
Your appliance allows the reception of audio signals sent since any devices having a
Bluetooth transmitter (Smartphone, tab, computer…).
First time association:
- Activate the Bluetooth connectivity of your emitter device;
- Select your appliance on the list of possible receiver (named ATOLL);
- Select the Bluetooth input of your IN300. The whole audio signals which will be
read on your device source will then be transmitted towards your IN300. Your emitter
device will remain associated until you switch off your IN300 but he will remain
visible for your emitter.
Association of another emitter:
Once associated to an emitter, you’ll need to switch completely your IN300 off in
order to make it visible from another emitter. The quality of reception of the signal
can be dependent on the power of the Bluetooth emitter and the distance between the
2 devices. Avoid being more than 5 meters of your IN300 for a correct reception
without any risks of signal cuts.
USING OF THE BY-PASS INPUT:
Careful: Put the volume at the minimum before any use of By-pass Input.
The By-pass Input offer you the capacity to use your Integrated as a Power amplifier
(plugged to an A/V processor a.i). This Input can be selected from the front panel or
with the BY-PASS key of the remote control (press during 3 seconds).
Once selected, mention « BY-PASS » appears on display. Then, no other functions
are available from front panel or remote Control. The Integrated can be used exactly
as a Power Amp. Press once By-pass to get back from By-pass.
REMOTE CONTROL:
The remote control is equipped with 2 Lithium CR2025 batteries. This remote control
is also able to drive all others ATOLL’s products: CD players; Tuner; Integrated or
preamplifier.
22) Volume setup - & + (from 0 to 80)
23) DISP: Selects On/off of display
24) Inputs selection
25) direct access to sources; to activate/deactivate
the By-pass Input, press during 3 seconds.
26) ON/OFF key : on stand-by, the appliance keeps
all parameters unchanged (source, volume level,
balance).
27) MUTE key: to get off the Mute, press any active
key of the remote control or turn a front knob.
28) Control of the balance: once on Balance menu, setup is operated with vol – & +
keys. You can setup balance level from -9 to +9.
29) Selection of the Digital Inputs
30) Selection of the Bluetooth Input
1 2 3 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18
24
27
28
26
22
29
30
25
23
19 20 21 22
Loading...