ATMEL AT89LV55-12AC, AT89LV55-12PI, AT89LV55-12PC, AT89LV55-12JI, AT89LV55-12JC Datasheet

...

203Features

•

Compatible with MCS-51™ Products

•

20K Bytes of Reprogrammable Flash Memory

– Endurance: 1,000 Write/Erase Cycles

•

Fully Static Operation: 0 Hz to 12 MHz

•

Three-Level Program Memory Lock

•

256 x 8-bit Internal RAM

•

32 Programmable I/O Lines

•

Three 16-bit Timer/Counters

•

Eight Interrupt Sources

•

Low Power Idle and Power Down Modes

•

2.7V to 6.0V Operating Range

Description

The AT89LV55 is a low-voltage, low-power CMOS 8-bit microcomputer with 20K bytes of Flash programmable and erasable read only memory. The device is manufactured using At mel’ s high dens ity nonv olat ile m emory te chnol ogy an d is compat ible with the industry sta nda rd 80 C51 in struction set and pi nou t. Th e o n- ch ip Flash allows the program memory to be rep rogrammed. By combining a ve rsatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89LV55 is a powerful microcomputer which provides a highly flex ible and co st effe ctive solu tion to many embedd ed con trol app lications.

(continued)

Pin Configurations

TQFP

PLCC

8-Bit Microcontroller with 20K Bytes Flash

AT89LV55

PDIP

0811B-B–12/97

4-193

Block Diagram

GND

P0.0 - P0.7

PORT 0 DRIVERS

P2.0 - P2.7

PORT 2 DRIVERS

RAM ADDR.

RAM

ACC

TMP2 TMP1

ALU

PSW

PORT 0

LATCH

INTERRUPT, SERIAL PORT,

PORT 2

LATCH

AND TIMER BLOCKS

STACK

POINTER

FLASH

PROGRAM

ADDRESS

BUFFER

INCREMENTER

PROGRAM

COUNTER

ALE/PROG

EA / V

4-194

PSEN

RST

TIMING

AND

CONTROL

OSC

INSTRUCTION

PORT 1

LATCH

PORT 1 DRIVERS

P1.0 - P1.7

DPTR

PORT 3

LATCH

PORT 3 DRIVERS

P3.0 - P3.7

AT89LV55

The AT89LV55 provides the following standard features: 20K bytes of Flash, 256-bytes of RAM, 32 I/O li nes, three 16-bit timer/counters, a six-vector two-level interrupt architecture, a full duplex serial port, on-chip os cillator, and clock circuitry. In addition, the AT89LV55 is designed with static logic for operation down to zero frequency and supports two softwar e selectable po wer saving modes . The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial p or t, and int er rupt s yst em to co nti nue functioning. The Power Down Mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next hardware reset. The low-voltage option saves power and operates with a 2.7-volt power supply.

Pin Description

Supply voltage.

GND

Ground.

Port 0

Port 0 is an 8-bit open drain bidirectional I/O port. As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as highimpedance inputs.

Port 0 can also be configu red to be the multiplex ed loworder address/data bus during accesses to ex ternal program and data memory. In this mode, P0 has internal pullups.

Port 0 also rece ives th e code by tes dur ing Fla sh prog ramming and outputs the code bytes during program ver ification. External pu llups are requ ired during pr ogram v erific ation.

Port 1

Port 1 is an 8-bit bidire ction al I/O por t w ith inter nal pullu ps. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins , they are p ulled hi gh by the internal pullups and can be used as inputs. As inputs , Port 1 pins that are externally being pulled low will source current (I

In addition, P1.0 and P1. 1 can be configured to be the timer/counter 2 external count input (P1.0/T2) and the timer/counter 2 trigger input (P1.1/T2EX), respectively, as shown in the following table.

Port Pin Alternate Functions

P1.0 T2 (external count input to Timer/Counter 2),

) because of the internal pullups.

clock-out

Port 2

Port 2 is an 8-bit bidirectional I/O port with interna l pullups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are writte n to Po rt 2 pi ns, they a re pul led high by the internal pullups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (I

) because of the internal pullups.

Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory th at u se 16 -b it a ddres s es ( MO VX @ DPTR). In this application, Port 2 uses strong internal pullups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register.

Port 2 also receives the high-order address bits and some control signals during Flash programming and verification.

Port 3

Port 3 is an 8-bit bidirectional I/O port with interna l pullups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are writte n to Po rt 3 pi ns, they a re pul led high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (I

) because of the pullups.

Port 3 also serv es t he fun ctions of v arious spe cial f eatures of the AT89LV55, as shown in the following table.

Port Pin Alternate Functions

P3.0 RXD (serial input port) P3.1 TXD (serial output port) P3.2 INT0 (external interrupt 0) P3.3 INT1 P3.4 T0 (timer 0 external input) P3.5 T1 (timer 1 external input) P3.6 WR P3.7 RD

(external interrupt 1)

(external data memory write strobe)

(external data memory read strobe)

Port 3 also receives the highest-order address bit and some control signals fo r Flash pro grammin g and veri fication.

RST

Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device.

P1.1 T2EX (Timer/Counter 2 capture/reload trigger and

direction control)

Port 1 also receives the low-order address bytes during Flash programming and verification.

4-195

ALE/PROG

Address Latch Enable is an output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG Flash programming.

In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency and may be used for external timing or clocking purposes. No te, however, that one ALE pulse is skipped durin g each access to extern al data me mory.

If desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution mode.

PSEN

Program Store Enable is the read strobe to external program memory.

When the AT89LV55 is executing code from external program memory, PSEN cycle, except that two PSEN each access to external data memory.

External Access Enable. EA must be strapped to GND in order to enable the device to fetch code from external program memory locations starting at 0000H up to FFFFH. Note, however, that if lock bit 1 is programmed, EA internally latched on reset.

should be strapped to VCC for internal program execu-

EA tions.

This pin also receives the 12-volt programming enable voltage (V

XTAL1

Input to the inverting os cillator ampl ifier and input to the internal clock operating circuit.

XTAL2

Output from the inverting oscillator amplifier.

) during 12-volt Flash programming.

is activated twice each machine

activations are skipped during

) during

will be

Timer 2 Registers:

registers T2CON (shown in Table 2) and T2MOD (shown in Table 4) for Timer 2. The register pair (RCAP2H, RCA P2L ) are the Capture/ Reloa d regist ers for Timer 2 i n 16-bit c apture mode or 16-bit auto-reload mode.

Interrupt Registers:

are in the IE register. Two priorities can be set for each of the six interrupt sources in the IP register.

Control and status bits are contained in

The individual interrupt enable bits

Data Memory

The AT89LV55 implements 256 bytes of on-chip RAM. The upper 128 bytes oc cupy a parall el address sp ace to the Special Function Registers. That means the upper 128 bytes have the same addresses as the SFR space but are physically separate from SFR space.

When an instruction accesses an internal location above address 7FH, the address mode used in the instruction specifies whether the CPU acce sses the u pper 128 bytes of RAM or the SFR space. Instructions that use direct addressing access SFR space.

For example, the following direct addressing instruction accesses the SFR at location 0A0H (which is P2).

MOV 0A0H, #data

Instructions that use indirect addressing access the upper 128 bytes of RAM. For example, the following indirect addressing inst ructi on, where R0 contains 0A 0H, a cc ess es the data byte at address 0A0H, rather than P2 (whose address is 0A0H).

MOV @R0, #data

Note that stack operations are examples of indirect addressing, so the upper 128 bytes of data RAM are avail able as stack space.

Special Function Registers

A map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 1.

Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect.

User software should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In th at case, th e reset or i nactive va lues of the new bits will always be 0.

4-196

AT89LV55

Table 1.

0F8H 0FFH

0F0H

0E8H 0EFH

0E0H

0D8H 0DFH

0D0H

0C8H

0C0H 0C7H

0B8H

0B0H

0A8H

0A0H

AT89LV55 SFR Map and Reset Values

00000000

ACC

00000000

PSW

00000000

98H

90H

88H

80H

T2CON

00000000

XX000000

11111111

0X000000

11111111

SCON

00000000

11111111

TCON

00000000

11111111

T2MOD

XXXXXX00

SBUF

XXXXXXXX

TMOD

00000000

00000111

RCAP2L

00000000

TL0

00000000

DPL

00000000

RCAP2H

00000000

TL1

00000000

DPH

00000000

TL2

00000000

TH0

00000000

TH2

00000000

TH1

00000000

PCON

0XXX0000

0F7H

0E7H

0D7H

0CFH

0BFH

0B7H

0AFH

0A7H

9FH

97H

8FH

87H

4-197

Table 2.

T2CON Address = 0C8H Reset Value = 0000 0000B Bit Addressable

T2CON—Timer/Counter 2 Control Register

TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2

Bit

Symbol Function

TF2 Timer 2 ove rflo w fla g set b y a Tim er 2 o v erfl ow an d m ust be clea red b y so ftwa re. TF2 will no t be set when eith er RCLK

EXF2 Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.

RCLK Receive clo ck enab le. Whe n set, caus es the serial port to use Timer 2 o v erflow pulses fo r its receiv e cl ock in serial port

TCLK Transmit clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in serial

EXEN2 Timer 2 external enable. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if

TR2 Start/Stop control for Timer 2. TR2 = 1 starts the timer. C/T2

CP/RL2

76543210

= 1 or TCLK = 1.

When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).

Modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.

port Modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.

Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.

Timer or counter select for Timer 2. C/T2 = 0 for timer function. C/T2 = 1 for external event counter (falling edge triggered).

Capture/Reload select. CP/RL2 = 1 causes captures to occur on negative tr ansiti ons at T2EX if EXEN2 = 1. CP/RL2 = 0 causes automatic reloads to occur when Timer 2 overflows or negative transitions occur at T2EX when EXEN2 = 1. When either RCLK or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.

CP/RL2

Timer 0 and 1

Timer 0 and 1 in the AT89LV55 operate the same way as Timer 0 and Timer 1 in the AT 89C51 and AT89C52. F or further information, see the Microcontroller Data Book, section titled, “Timer Counters.”

Timer 2

Timer 2 is a 16-bit Timer/Counter that can operate as either a timer or an event counter. The type of operation is selected by bit C/T2 Timer 2 has three operating modes: capture, auto-reload (up or down counting), and baud rate generator. The modes are selected by bits in T2CON, as shown in Table 3.

Timer 2 consists of two 8- bi t regi st er s, TH2 and TL2. I n the Timer function, the TL2 r egister is incremented ever y machine cycle. Since a machine cycle consists of 12 oscillator periods, the count rate is 1/12 of the oscillator frequency.

In the Counter function, the register is incremented in response to a 1-to-0 transition at its corresponding external input pin, T2. In thi s func tion, the extern al i nput is sa mpled during S5P2 of every machin e cycle. When the samples

in the SFR T2 C ON (sh o w n i n Ta bl e 2).

show a high in one cycle and a low in the next cycle, the count is incremented. The new count value appears in the register during S3P1 of the cycle following the one in which the transition was detected. Since two machine cycles (24 oscillator perio ds ) ar e re qui red to recognize a 1-to -0 transition, the maximum count rate is 1/24 of the oscillator frequency. To ensure that a given level is sampled at least once before it changes, the level should be held for at least one full machine cycle.

Table 3.

Timer 2 Operating Modes

RCLK + TCLK CP/RL2 TR2 MODE

0 0 1 16-bit Auto-Reload 0 1 1 16-bit Capture 1 X 1 Baud Rate

Generator

X X 0 (Off)

4-198

AT89LV55

Capture Mode

In the capture mode, two option s are selected by bit EXEN2 in T2CON. If EXEN2 = 0, Timer 2 is a 16-bit timer or counter which upon overflow sets bit TF2 in T2CON. This bit can then be used to generate an interrupt. If EXEN2 = 1, Tim er 2 p erfor ms t he s ame op erati on, but a 1-

Figure 1.

Timer 2 in Capture Mode

to-0 transition at external input T2EX also causes the current value in TH2 and TL2 to be captured into RCAP2H and RCAP2L, respec tively. In addition, the tran sition at T2EX causes bit EXF2 in T2CON to be set. The EXF2 bit, li ke TF2, can generate an interrupt. The capture mode is illustrated in Figure 1.

Auto-Reload (Up or Down Counter)

Timer 2 can be programmed to count up or down when configured in its 16-bit auto-reload mode. This feature is invoked by the DCEN (Down Counter Enable) bit located in the SFR T2MOD (see Table 4). Upon reset, the DCEN bit is set to 0 so that tim er 2 will default to count up. Wh en DCEN is set, Timer 2 can coun t up or down, depend ing on the value of the T2EX pin.

Figure 2 shows Timer 2 aut omatically counting u p when DCEN = 0. In this mod e, two options a re selecte d by bit EXEN2 in T2CON. If EXEN2 = 0, Tim er 2 counts up to 0FFFFH and then sets the TF2 bit upon overflow. The overflow also causes the tim er r egi ste rs to be r e loa ded with the 16-bit value in RCAP2H and RCAP2L. The values in RCAP2H and RCAP2L are preset by software. If EXEN2 = 1, a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at external input T2EX. This transition also sets the EXF2 bit. Both th e TF2 and EXF2 bits c an generate an interrupt if enabled.

Setting the DCEN bit ena ble s Ti mer 2 t o c ount up o r d own, as shown in Figure 3. In this mode, the T2EX pin controls the direction of the count. A logic 1 at T2EX makes Timer 2 count up. The timer will overflow at 0FFFFH and set the TF2 bit. This overflow also causes the 16-bit value in RCAP2H and RCAP2L to be reloaded into the timer registers, TH2 and TL2, respectively.

A logic 0 at T2EX makes Timer 2 count down. The timer underflows when TH2 and TL2 equal the values stor ed in RCAP2H and RCAP2L. The underflow sets the TF2 bit and causes 0FFFFH to be reloaded into the timer registers.

The EXF2 bit toggles whenever Timer 2 overflows or underflows and can be used as a 17th bit of resolution. In this operating mode, EXF2 does not flag an interrupt.

4-199

+ 16 hidden pages