Atlona Portable HDMI Signal
Generator with 3D Patterns
AT-HD800
atlona.com
User Manual
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Table of Contents
1. Introduction ............................................................................................ 3
2. Package Contents ............................................................................................ 3
3. Features ............................................................................................ 3
4. Specifications ............................................................................................ 3
5. Panel Descriptions ............................................................................................ 4
6. Battery Door ............................................................................................ 5
7. HDMI Cable Testing ............................................................................................ 5
8. Timing Chart ............................................................................................ 5
9. Pattern Chart ............................................................................................ 6-8
10. Connection and Installation ............................................................................................ 9
11. Safety Information ............................................................................................ 10
12. Warranty ............................................................................................ 11
13. Atlona Product Registration ............................................................................................ 12
atlona.com
2
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Introduction
With so many potential problems in any installation it’s always better to be ready before the
problem starts. With the Atlona Portable HDMI Signal Generator, test HDMI cables, determine
compatible resolutions, and read EDIDs before installation to avoid problems or after to
troubleshoot compatibility issues. Save time and avoid guesswork with the AT-HD800.
Package Contents
• 1 x AT-HD800
• 1 x 5V/2A Power Supply
• 4 x AA Batteries
• 1 x Rubber Case
• 1 x User Manual
Features
• Supports 16 Test Patterns which includes 3-3D patterns.
• Cable integrity testing ability
• Vesa testing resolutions: 640x480(VGA), 800x600(SVGA), 1024x768(XGA),
1280x1024(SXGA), 1920x1200(WUXGA)
• Video testing resolutions: 480i/p, 576i/p, 720p(50/60Hz), 1080i(50/60Hz), 1080p(24/50/60)
• 3D Video testing resolutions: 720p(50/60Hz), 1080p 24Hz
• 2-channel LPCM is always active to test audio 1Khz frequency at -20dB volume
• EDID Reading function, allows user to view the displays capabilities
• HDMI ports are designed for reading EDID from both source and display capabilities side
by side. This helps to prevent a lot of issues with installation and also troubleshooting the
compatibilities in applications where a lot of equipment is used.
• Protective rubber case included
• Last memory function, allows the generator remember the setting the user had prior to
powering OFF.
Specifications
Bandwidth frequency 6.75Gbps
Input Ports 1 x HDMI
Output Ports 1 x HDMI
Resolution outputs Video: up to 1080p
Vesa: up to 1920x1200
Dimensions (HxWxD) 1x3.5x5 (inch) or 25.4x88.9x127 (mm)
Weight 0.4lbs or 0.18kg
Temperature Operating: 32°F to 104°F or 0°C to 40°C
Storage: -4°F to 140°F or -20°C to 60°C
Power consumption 2.1W (Bypass), 1.1W (Pattern)
atlona.com
3
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Panel Description
1 2 3 4 5 6 7 8 9 10
1. DC 5V: Input port for the included 5V DC Adapter.
2. Power Switch: Turns the AT-HD800 on (switch up) and off (switch down)
Note: To switch to power over 5V DC adapter, when the batteries are low, power cycle the
AT-HD800 with the power switch.
3. HDMI IN: Connect an HDMI cable from a source, or HDMI loop for cable testing.
4. HDMI OUT: Connect an HDMI cable to a display, or HDMI loop for cable testing.
Note: Loop the HDMI cable from the HDMI Out to the HDMI In for cable testing.
5. BATT. LOW LED: Red led will light up when the power is on. The LED will start flashing fast
when the batteries get to 10% or below or slow when it is put in standby mode.
Note: Standby will occur after 3 minutes of inactivity with nothing plugged into the ports of
the AT-HD800. (The AT-HD800 will not go into standby when using the 5V adapter.)
6. Bypass/Pattern LED: Green LED will illuminate when receiving signal from an HDMI source.
LED will be off if no HDMI source is connected.
7. 3D/PC/HD LED:
a. LED will flash when receiving or sending a 3D signal.
b. LED will be a solid green when sending or receiving a VESA resolution
c. LED will be off when receiving or sending a video resolution.
8. 50/60 Hz LED: Will illuminate green when sending/receiving a 50Hz signal.
(Most commonly used in Europe and Asia)
Note: To quickly switch between 50 & 60Hz press and hold the Timing Select & Info Pattern
buttons together for 3 seconds then release.
9. Timing Select Button: Press once to bring up the resolution menu on the display (not
available when an HDMI source is connected). Press the timing select button again to
go through the 25 available timing/resolutions (press the Info Pattern button to go
backwards)
10. Info Pattern Button
a. HD800 to Display: Press once to bring up the pattern menu. Press continuously to go
through the patterns. (Press the Timing Select Button to go back to a pattern.)
b. Source to HD800 to Display: Pressing the Info Pattern Button will show the source
and display capabilities side by side on the display’s screen.
Note: If there is no image present, press the Info Pattern Button 3 seconds then release. The
resolution will be reset to the Display’s native resolution.
atlona.com
4
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Loading...