Atlas Metal WCPT-3 Service Manual

WCPT-3 and WCPT-4

Service and Installation Manual

Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately. See page 1.

Drop-in Display Cases

Effective Date: 2017

IMPORTANT INFORMATION

READ BEFORE USE

Project: ___________ Item No.: ___________ Quantity: ___________

DROP-IN SERVING EQUIPMENT

DISPLAY CASE

Refrigerated, Pass-Through Self-Contained

WCPT-3 WCPT-4

SPECIFICATIONS

TOP: Constructed of 18 gauge, type 304 stainless steel, die stamped

with a raised perimeter bead. The top is solid, full-length, to support the refrigerated display case. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top.

DISPLAY CASE: Double wall constructed of type 304 stainless steel

- 20 gauge, both interior and exterior, and filled with 2" of foamed-inplace polyurethane insulation. Customer's side and operator's side are provided with a set of two (2) sliding, self-closing, thermo-pane, insulated glass doors. The doors are removable for ease of cleaning. The display case is provided with two (2) plastic coated wire shelves, adjustable on 1" increments, and two (2) sets of fluorescent light fixtures mounted behind plastic guards which are recessed into the side panels. The light fixtures are provided with a separate on/off switch. An internal thermometer is provided.

REFRIGERATION SYSTEM: The compressor housing shall be fabricated from 14 gauge galvanized and bolted to the base of the unit. A fully self-contained condensing unit is provided with a hermetically sealed compressor and a thermostat control. The system is also provided with a forced air evaporator, for even temperature throughout the display case, which drains into a condensate evaporator, prewired in the unit. The system is fully charged with CFC free refrigerant and ready to operate.

NOTE: Proper ventilation must be provided in counter.

ELECTRICAL: The unit will be wired for 15 amps., 120 volt, single

phase operation with an on/off thermostat switch and pilot light. A 6' long, 3-wire cord and plug (NEMA 5-15P) will be provided.

STANDARD FEATURES

Large, lighted display area with adjustable shelves - it’s the

ideal merchandiser

Sliding glass doors on customer’s and operator’s side,

making loading and self-service move quickly

Forced air evaporator blower system for maximum efficiency

in cooling

g Factory applied gasket - makes installation a snap and seals

units to the counter top, thus eliminating seepage

1-Year Parts & Labor Warranty

UL Recognized

ACCESSORIES

5YW - 5-Year Compressor Warranty

g Door Locking Device (2 required) g Extra Shelf g Plastic Laminate Trim g Sliding Doors with Reflective Tempered Vision Panel (bronze

or gray)

g Solid (1) piece Tempered Reflective Vision Panel (bronze or

gray)

g Solid Stainless Steel Back g

RS - Remote on/off switch for counter mounting

g RDVE - Rear Drain Valve Extension g * 220 Volt - 50 Cycle Compressor

Specifications subject to change without notice.

*Please see Operation & Installation Manual for ALL operation and maintenance details.

* Units with these accessories are not currently UL listed.

DI-39

REFRIGERATED PASS THROUGH DISPLAY CASE

WCPT SERIES

--------------------------------------------------------------------------------------------------------------------------------------------------------------------

INSTALLATION

Provide the correct counter cut-out opening (see chart below) and drop unit in. The vinyl gasket assures complete seating. A non-toxic silicone sealer may be used between the gasket and counter top (not required).

MODEL

WCPT-3 22 1/4" X 41 3/4" WCPT-4 22 1/4" X 55 1/2"

The unit should be level for draining purposes. When installing unit in counter, it is recommended that the operator side of the counter be completely open for air circulation. When this is not possible, such as in an island counter, it is recommended that two grill openings are provided approximately 18” x 18” of free air for intake and exhaust at the opposite ends of counter. Also the counter must have an opening of approximately 24” x 14” to access the compressor for maintenance. Then the refrigeration components can be reached by removing six (6) screws from control and rear panels. The unit is supplied with a power cord and NEMA plug. Refer to data plate on compressor housing for the amperage and voltage information. Use a licensed electrician when installing power source. For cleaning and maintenance of inside top evaporator coil a qualified refrigeration technician is recommended.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------

CUT-OUT

REQUIRED

OPERATION

The unit is ready to be operated as soon as it is plugged in and switched on. The unit has been pre-tested for proper operation from 35 to 40 degrees.

-------------------------------------------------------------------------------------------------------------------------------------------

---------------------------------------------------------------------------------------------------------------------------------------

MAINTENANCE

NEVER CLEAN THE UNIT WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER CLEANING COULD SCAR, MARK AND/OR CORRODE METAL. DO NOT USE STEEL WOOL OR ABRASIVE PRODUCTS. TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO REMOVE ALL RESIDUES. CLEAN CONDENSER COIL REGULARLY. FAILURE TO MEET THESE CONDITIONS WILL VOID WARRANTY.

+ 8 hidden pages