Atlantic PANEL HEATER User Manual
11
11
1
22
22
2
55
55
5
Feet and castors not
to be fitted on high
end plinth models
99
99
9
66
66
6
Diagram
corresponding
to high version
500W
77
77
7
88
88
8
33
33
3
44
44
4
The product you have just purchased has undergone numerous tests and inspections to guarantee the highest quality.
We hope it will give you entire satisfaction.
2) How to install the panel heater ?
2-1) Mount the wall support
A : Standard and high version
346346
346346
346
B : Plinth and Low version
7878
7878
78
- Mount the panel heater on mounting S as shown. Lock the lock V.
44
44
4
Note : Do not use the device in mobile or feets or on casters
55
55
5
, except the range kit feet (ref. 417010 - 417015 -
417020) and Australian ranges : Standard and Low.
2-2) Connecting the panel heater
- The panel heater must be powered with 220-240V 50Hz
- The panel heater must be connected to the mains, either by a 2-wire cable (Brown = Phase, Blue = Neutral) via a power
socket.
In humid areas such as bathrooms and kitchens the power socket must be installed at least 25 cm above the floor.
- The installation must be equipped with a omnipole disconnexion mechanism with a break contact distance of at least 3mm.
- Earthing is prohibited. Do not connect the pilot wire (black) to earth.
- The heater must be installed by a qualified electrician in accordance with the local regulations. The heater and the pilot
wire (black) must NOT be connected to earth. If the heater wire is damaged, it must be replaced by a qualified person
to avoid hazard.
If a pilot or piloted panel heater is protected by 30mA differential (e.g. bathroom) the pilot wire’s power must be
protected on this differential.
Please read the instructions before starting to install the heater. Disconnect the power before carrying out any work on
the heater. Keep these instructions even once you have installed your heater.
1) Where to install your heater ?
- This equipment was designed to be installed in a residence. Please ask your distributor before using it for any other purpose.
- The panel heater should be installed according to normal trade practice and in compliance with legislation in the
relevant country (the IEE Wiring Regulations).
- The equipment is class 2
and is protected against splashed water IP 24. Therefore it can be installed in
volume 2, provided the panel heater’s controls cannot be reached by a person using the shower or bath.
11
11
1
- Comply with the minimum clearance distances for positioning of the panel heater.
22
22
2
- If your wall covering is laid on foam, a spacer the same thickness as the foam must be placed under the panel
heater’s support. This ensures there is free space behind the panel heater to make sure its control settings are not
adversely affected.
- Do not install the panel heater:
➫ In a draught likely to affect the control settings (under a fan, etc.).
➫ Under a fixed mains power socket.
Except in the UK. Please refer to the IEE Regulations 601-06-01 and 601-08-01 (BS7671).
sdnammoC
deviecer
oNtnerruc
Clpmoeet
noitanretla
032V
Nevitagé
flahnoitanretla-
-511V
isoPevit
flahnoitanretla-
+511V
epocsollicsOs
rtueN/féRla
edoM
tbodenia
OCM TROFOCEEZEERF-ITNA
TUCREWOP
POTS
It is strongly recomended not to install vertical products we manufacture above an altitude of 1000
metres. If the device is installed at altitude the air discharge temperature will be increased (by
approximately 10°C per 1000 m of altitude).
It is forbiden to install vertical product in horizontal position.
INSTALLATION OF THE PANEL HEATER
Loading...