AWGR54
P75234
© 2006 Ativa. All rights reserved. All trade names are registered trademarks of respective manufacturers listed.
Apple, AirPort, Mac, Mac OS, and AppleTalk are trademarks of Apple Computer, Inc., registered in the U.S. and
other countries. Windows, NT, and Microsoft are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Ativa Tech Support
US: 1-866-91-ATIVA (1-866-912-8482)
www.ativasupport.com
Wireless G
Router
AWGR54
User Manual
Wireless G
Router
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Benefits of a Home Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Knowing your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Easy Install Wizard Software System Requirements . . . . . . . . . . . . . 9
4. Connecting and Configuring your Router . . . . . . . . . . . . . . . . . . . 14
5. Alternate Setup Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6. Using the Web-Based Advanced User Interface . . . . . . . . . . . . . 37
Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Viewing the DHCP Client List Page . . . . . . . . . . . . . . . . . . . . . . . . . 40
Configuring the Wireless Network Settings . . . . . . . . . . . . . . . . . . 40
Securing your Wi-Fi Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
WEP Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
WPA Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Setting WPA/WPA2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Using the Access Point Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Configuring the Firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Setting MAC Address Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Restarting the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7. Manually Configuring Network Settings . . . . . . . . . . . . . . . . . . . . 76
8. Recommended Web Browser Settings . . . . . . . . . . . . . . . . . . . . . . 81
9. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
10. Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
1
2
1
3
4
5
6
7
8
9
10
section
Introduction
Thank you for purchasing the Ativa Wireless G Router (the Router). The following
two short sections discuss the benefits of home networking and outline best
practices for maximizing your wireless home network range and performance.
Please be sure to read through this User Manual completely, and pay special
attention to the section entitled “Placement of your Router for Optimal
Performance” on page 2.
Benefits of a Home Network
• Share one high-speed Internet connection with all the computers
in your home
• Share resources, such as files and hard drives among all the connected
computers in your home
• Share a single printer with the entire family
• Share documents, music, video, and digital pictures
• Store, retrieve, and copy files from one computer to another
• Simultaneously play games online, check Internet email, and chat
Advantages of a Wireless Network
• Mobility – you’ll no longer need a dedicated “computer
room”—now you can work on a networked laptop or desktop computer
anywhere within your wireless range
• Easy installation – The Ativa Easy Installation Wizard makes
setup simple
• Flexibility – set up and access printers, computers, and other networking
devices from anywhere in your home
• Easy expansion – the wide range of Ativa networking products lets
you expand your network to include devices such as printers and
gaming consoles
• No cabling required – you can spare the expense and hassle of
retrofitting Ethernet cabling throughout the home or office
• Widespread industry acceptance – choose from a wide range of
interoperable networking products
Introduction
2
Placement of your Router for Optimal Performance
Important Factors for Placement and Setup
Your wireless connection will be stronger the closer your computer is to your
Router. Typical indoor operating range for wireless devices is between 100 and
200 feet.
In the same way, your wireless connection and performance will degrade
somewhat as the distance between your Router and connected devices
increases. This may or may not be noticeable to you. As you move farther
from your Router, connection speed may decrease. Factors that can weaken
signals simply by getting in the way of your network’s radio waves are metal
appliances or obstructions, and walls.
If you have concerns about your network’s performance that might be related
to range or obstruction factors, try moving the computer to a position
between five and 10 feet away from the Router in order to see if distance is
the problem. If difficulties persist even at close range, please contact Ativa
Technical Support.
Note: While some of the items listed below can affect network performance,
they will not prohibit your wireless network from functioning; if you are
concerned that your network is not operating at its maximum effectiveness,
this checklist may help.
1. Wireless Router Placement
Place your Router, the central connection point of your network, as close
as possible to the center of your wireless network devices.
To achieve the best wireless network coverage for your “wireless clients”
(i.e., computers enabled by Ativa Wireless Notebook Network Cards,
Wireless Desktop Network Cards, and Wireless USB Adapters):
• Ensure that your Router’s networking antennas are parallel to each
other, and are positioned vertically (toward the ceiling). If your
Router itself is positioned vertically, point the antennas as much as
possible in an upward direction.
• In multistory homes, place the Router on a floor that is as close
to the center of the home as possible. This may mean placing the
Router on an upper floor.
• Try not to place the Router near a cordless phone.
3
2
1
3
4
5
6
7
8
9
10
section
Introduction
2. Avoid Obstacles and Interference
Avoid placing your Router near devices that may emit radio “noise,”
such as microwave ovens. Dense objects that can inhibit wireless
communication include:
• Refrigerators
• Washers and /or dryers
• Metal cabinets
• Large aquariums
• Metallic-based, UV-tinted windows
If your wireless signal seems weak in some spots, make sure that objects
such as these are not blocking the signal’s path (between your computers
and Router).
3. Cordless Phones
If the performance of your wireless network is impaired after attending
to the above issues, and you have a cordless phone:
• Try moving cordless phones away from the Router and your
wireless-enabled computers.
• Unplug and remove the battery from any cordless phone that operates
on the 2.4GHz band (check the manufacturer’s information). If this
fixes the problem, your phone may
be interfering.
• If your phone supports channel selection, change the channel on
the phone to the farthest channel from your wireless network. For
example, change the phone to channel 1 and move your Router to
channel 11. See your phone’s user manual for detailed instructions.
• If necessary, consider switching to a 900MHz cordless phone.
4. Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as apartment
buildings or office complexes, there may be wireless networks nearby
that can conflict with yours.
Use the Site Survey capabilities found in the wireless utility of your
wireless adapter or card to locate any other wireless networks that are
available (see your wireless adapter’s or card’s user manual), and move
your Router and computers to a channel as far away from other networks
as possible.
Introduction
4
• Experiment with more than one of the available channels in order to
find the clearest connection and avoid interference from neighboring
cordless phones or other wireless devices.
• For Ativa wireless networking products, use the detailed Site Survey and
wireless channel information included with your Wireless Network Card
or Adapter. See your Network Card’s user guide for more information.
These guidelines should allow you to cover the maximum possible area
with your Router.
5. Secure Connections, VPNs, and AOL
Secure connections typically require a user name and password, and are
used where security is important. Secure connections include:
• Virtual Private Network (VPN) connections, often used to connect
remotely to an office network
• The “Bring Your Own Access” program from America Online (AOL),
which lets you use AOL through broadband provided by another cable
or DSL service
• Most online banking websites
• Many commercial websites that require a user name and password to
access your account
Secure connections can be interrupted by a computer’s power
management setting, which causes it to “go to sleep.” The simplest
solution to avoid this is to simply reconnect by rerunning the VPN or AOL
software, or by re-logging into the secure website.
A second alternative is to change your computer’s power management
settings so it does not go to sleep; however, this may not be appropriate
for portable computers. To change your power management setting under
Windows, see the “Power Options” item in the Control Panel.
If you continue to have difficulty with Secure Connections, VPNs, and
AOL, please review the steps above to be sure you have addressed
these issues.
5
2
1
3
4
5
6
7
8
9
10
section
Introduction
For more information regarding our networking products, visit our website at
www.ativasupport.com or call Ativa Technical Support at:
US: 1-866-91-ATIVA (1-866-912-8482)
Product Overview
6
Product Features
In minutes you will be able to share your Internet connection and network
your computers. The following is a list of features that make your new Ativa
Wireless G Router an ideal solution for your home or small office network.
Works with Both PCs and Mac® Computers
The Router supports a variety of networking environments including Mac
OS® X v10.x, AppleTalk®, Linux®, Windows® 98, Me, NT®, 2000, and XP, and
others. All that is needed is an Internet browser and a network adapter that
supports TCP/IP (the standard language of the Internet).
Front-Panel LED Display
Lighted LEDs on the front of the Router indicate which functions are in
operation. You’ll know at-a-glance whether your Router is connected to
the Internet. This feature eliminates the need for advanced software and
status-monitoring procedures.
Web-Based Advanced User Interface
You can set up the Router’s advanced functions easily through your web
browser, without having to install additional software onto the computer.
There are no disks to install or keep track of and, best of all, you can make
changes and perform setup functions from any computer on the network
quickly and easily.
NAT IP Address Sharing
Your Router employs Network Address Translation (NAT) to share the single
IP address assigned to you by your Internet Service Provider while saving the
cost of adding IP addresses to your Internet service account.
SPI Firewall
Your Router is equipped with a firewall that will protect your network from a
wide array of common hacker attacks including IP Spoofing, Land Attack, Ping
of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP
Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect,
and fragment flooding.
7
2
1
3
4
5
6
7
8
9
10
section
Product Overview
Integrated 10/100 4-Port Switch
The Router has a built-in, 4-port network switch to allow your wired
computers to share printers, data and MP3 files, digital photos, and much
more. The switch features automatic detection so it will adjust to the speed of
connected devices. The switch will transfer data between computers and the
Internet simultaneously without interrupting or consuming resources.
Universal Plug-and-Play (UPnP) Compatibility
UPnP (Universal Plug-and-Play) is a technology that offers seamless operation
of voice messaging, video messaging, games, and other applications that are
UPnP-compliant.
Support for VPN Pass-Through
If you connect to your office network from home using a VPN connection,
your Router will allow your VPN-equipped computer to pass through the
Router and to your office network.
Built-In Dynamic Host Configuration Protocol (DHCP)
Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for
the easiest possible connection of a network. The DHCP server will assign
IP addresses to each computer automatically so there is no need for a
complicated networking setup.
Easy Install Wizard
The Easy Install Wizard takes the guesswork out of setting up your Router.
This automatic software determines your network settings for you and sets up
the Router for connection to your Internet Service Provider (ISP). In a matter
of minutes, your Wireless Router will be up and running on the Internet.
NOTE: Easy Install Wizard software is compatible with Windows 98SE, Me,
2000, and XP; and Mac OS X. If you are using another operating system, the
Wireless Router can be set up using the Alternate Setup Method described in
this User Manual (see page 22).
Product Overview
8
Integrated 802.11g Wireless Access Point
802.11g is an exciting new wireless technology that achieves data rates up to
54Mbps, nearly five times faster than 802.11b.
MAC Address Filtering
For added security, you can set up a list of MAC addresses (unique client
identifiers) that are allowed access to your network. Every computer has its
own MAC address. Simply enter these MAC addresses into a list using the
Web-Based Advanced User Interface and you can control access to
your network .
Package Contents
• Ativa Wireless G Router
• Quick Installation Guide
• Ativa Easy Install Wizard Software CD with User Manual
• Ativa RJ45 Ethernet Networking Cable
• Power Supply
System Requirements
• Broadband Internet connection such as a cable or DSL modem with
RJ45 (Ethernet) connection
• At least one computer with an installed network interface adapter
• TCP/IP networking protocol installed on each computer
• RJ45 Ethernet networking cable
• Internet browser
Easy Install Wizard Software System Requirements
• A PC running Windows 98SE, Me, 2000, or XP; or a Mac computer
running Mac OS X
• Minimum 64MB RAM
• Internet browser
9
2
1
3
4
5
6
7
8
9
10
section
Knowing your Router
Knowing your Router
10
The Router has been designed to
be placed on a desktop. All of the
cables exit from the rear of the
Router for better organization and
utility. The LED indicators are easily
visible on the front of the Router to
provide you with information about
network activity and status.
1. Power/Ready LED
When you apply power to the Router or restart it, a short period of time
elapses while the Router boots up. During this time, the Power/Ready LED
blinks. When the Router has completely booted up, the Power/Ready LED
becomes a SOLID light, indicating the Router is ready for use.
OFF Router is OFF
Blinking Blue Router is Booting Up
Solid Blue Router is Ready
2. Wireless Network LED
OFF Wireless Network is OFF
Blue Wireless Network is Ready
Blinking Blue Indicates Wireless Activity
3. Wired Computer Status LEDs
These LEDs are labeled 1–4 and correspond to the numbered ports on the
rear of the Router. When a computer is properly connected to one of the
wired computer ports on the rear of the Router, the LED will light. BLUE
means a 10/100Base-T device is connected. When information is being sent
over the port, the LED blinks rapidly.
OFF No Device is Linked to the Port
Blue 10/100Base-T Device Connected
Blinking Blue Port Activity
(1)
(2)
(3)
(5)
(4)
11
2
1
3
4
5
6
7
8
9
10
section
Knowing your Router
4. Modem Status LED
This LED lights in BLUE to indicate that your modem is connected
properly to the Router. It blinks rapidly when information is being sent
over the port between the Router and the modem.
OFF No WAN Link
Solid Blue Good WAN Link
Blinking Blue WAN Activity
5. Internet LED
This unique LED shows you when the Router is connected to the
Internet. When the light is OFF, the Router is NOT connected to the
Internet. When the light is blinking, the Router is attempting to connect
to the Internet. When the light is solid BLUE, the Router is connected
to the Internet. When using the “Disconnect after x minutes” feature,
this LED becomes extremely useful in monitoring the status of your
Router’s connection.
OFF Router is not Connected to the Internet
Blinking Blue
Router is Attempting to Connect to
the Internet
Solid Blue Router is Connected to the Internet
Knowing your Router
12
6. Power Jack
Connect the included 5V DC power supply to this jack.
7. Connections to Computers (Wired Computer Ports)
Connect your wired (non-wireless) computers to these ports. These ports
are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP
category 5 or 6 Ethernet cable. The ports are labeled 1 through 4. These ports
correspond to the numbered LEDs on the front of the Router.
8. Connection to Modem (Modem Port)
This port is for connection to your cable or DSL modem. Use the cable that was
provided with the modem to connect the modem to this port. Use of a cable
other than the cable supplied with the cable modem may not work properly.
(9)
Reset button is
located on the
side of the unit.
(6)
(7)
(8)
13
2
1
3
4
5
6
7
8
9
10
section
Knowing your Router
9. Reset Button
The “Reset” button is used in rare cases when the Router may function
improperly. Resetting the Router will restore the Router’s normal
operation while maintaining the programmed settings. You can also
restore the factory default settings by using the “Reset” button. Use
the restore option in instances where you may have forgotten your
custom password.
a. Resetting the Router
Push and release the “Reset” button. The lights on the Router
will momentarily flash. The Power/Ready light will begin to
blink. When the Power/Ready light becomes solid again, the
reset is complete.
b. Restoring the Factory Defaults
Press and hold the “Reset” button for at least 10 seconds, then
release it. The lights on the Router will momentarily flash. The
Power/Ready light will begin to blink. When the Power/Ready light
becomes solid again, the restore is complete.
Connecting and Configuring your Router
14
Verify the contents of your box. You should have the following:
• Ativa Wireless G Router
• Quick Installation Guide
• Ativa Easy Install Wizard Software CD with User Manual
• RJ45 Ethernet Networking Cable (for connection of the
Router to the computer)
• Power Supply
• Wireless Security Setup Guide
Modem Requirements
Your cable or DSL modem must be equipped with an RJ45 Ethernet port. Many
modems have both an RJ45 Ethernet port and a USB connection. If you have
a modem with both Ethernet and USB, and are using the USB connection at
this time, you will be instructed to use the RJ45 Ethernet port during the
installation procedure. If your modem has only a USB port, you can request a
different type of modem from your ISP, or you can, in some cases, purchase a
modem that has an RJ45 Ethernet port on it.
Ethernet USB
ALWAYS INSTALL YOUR ROUTER FIRST! IF YOU ARE INSTALLING
NUMEROUS NETWORK DEVICES FOR THE FIRST TIME, IT IS IMPORTANT THAT
YOUR ROUTER IS CONNECTED AND RUNNING BEFORE ATTEMPTING TO
INSTALL OTHER NETWORK COMPONENTS SUCH AS NOTEBOOK CARDS AND
DESKTOP CARDS.
Easy Install Wizard
Ativa has provided our Easy Install Wizard software to make installing your
Router a simple and easy task. You can use it to get your Router up and
running in minutes. The Easy Install Wizard requires that your Windows 98SE,
Me, 2000, or XP; or Mac OS X v10.1.x computer be connected directly to your
cable or DSL modem and that the Internet connection is active and working
at the time of installation. If it is not, you must use the “Alternate Setup
Method” section of this User Manual to configure your Router. Additionally, if
you are using an operating system other than Windows 98SE, Me, 2000, or XP,
you must set up the Router using the “Alternate Setup Method” section of this
User Manual.
15
2
1
3
4
5
6
7
8
9
10
section
Connecting and Configuring your Router
IMPORTANT: Run the Easy Install Wizard software from the computer that
is directly connected to the cable or DSL modem. DO NOT CONNECT THE
ROUTER AT THIS TIME.
Step 1 Run the Easy Install Wizard Software
1.1 Shut down any programs that are running on your computer at this time.
1.2 Make sure you have the following items at the computer that is now
directly connected to the cable or DSL modem. DO NOT CONNECT THE
ROUTER AT THIS TIME.
• Quick Installation Guide
• The Easy Install Wizard Software CD with User Manual
• The Router
• The Router’s Power Supply
• RJ45 Ethernet Networking Cable
1.3 Turn off any firewall or Internet-connection-sharing software
on your computer.
1.4 Insert the Easy Install Wizard software CD into your CD-ROM drive.
The Easy Installation Wizard screen will automatically appear on your
screen within 15 seconds. If it does not, select your CD-ROM drive from
“My Computer” and double-click on the file named “EasyInstall.exe”
on the CD-ROM.
Connecting and Configuring your Router
16
Welcome Screen
After you insert the CD into your
CD-ROM drive, the Wizard’s welcome screen
will appear. Make sure you have not connected
the Router at this point. If you have
connected your Router, please reconnect your
computer directly to the modem. Click “Run
the Easy Install Wizard” when you are ready to
move on.
Progress Screen
The Easy Install Wizard will show you a
progress screen each time a step in the setup
has been completed. Each time you see the
progress screen, click “Next” when you are
ready to move to the next step.
Examining Settings
The Wizard will now examine your computer’s
network settings and gather information
needed to complete the Router’s connection
to the Internet. When the Wizard is finished
examining your computer, click “Next”
to continue.
Multiple Network Adapters Found Screen
If you have more than one network adapter
installed in your computer, this screen will
appear. If you have more than one network
adapter installed in your computer, you
must designate for the Wizard which adapter
is connected to your modem. To do this,
select it from the list and click “Next”. If
you are not sure which adapter to choose,
select the adapter at the top of the list. If
you mistakenly choose the wrong adapter
now, you will be able to choose a different
one later.
17
2
1
3
4
5
6
7
8
9
10
section
Connecting and Configuring your Router
Step 2 Set up the Hardware
The Wizard will walk you through connecting your Router to your computer and
modem. Follow the steps on the screen using the pictures as a guide.
2.1 This step instructs you to locate
the cable connected between your
modem and the networking port on
your computer. Unplug this cable
from the computer and plug it into
the modem port on the Router. Click
“Next” to continue.
2.2 This step instructs you to locate
the BLUE cable that is included
with your Router. Plug one end
of this cable into ANY one of the
wired-computer ports on your
Router. Plug the other end of the
cable into the networking port on
your computer. Click “Next”
to continue.
2.3 This step instructs you to locate the
power supply that is included with
your Router. Plug the power supply’s
small connector into the power port
on the Router. Plug the power supply
into an empty power outlet. Click
“Next” to continue.
Connecting and Configuring your Router
18
2.4 This step instructs you to look at the
lights on the front of your Router. Make
sure the appropriate lights are ON. Refer
to the Easy Install Wizard software on
your computer’s screen for more details.
Click “Next” to continue.
Note: The Easy Install Wizard may ask
you to reboot your computer. If it does,
reboot your computer and proceed with
the installation.
Step 3 Check the Connection
3.1 Once you have completed connecting
the Router, the Wizard will check the
connection to the Router and then go
on to determine what type of Internet
connection you have.
3.2 User Name and Password Needed
If you have a connection type that
requires a user name and a password, the
Wizard will ask you to type in your user
name and password. If your connection
type does not require a user name and
password, you will not see this screen.
Your user name and password is provided
to you by your Internet Service Provider.
If you have to type in a user name and
password to connect to the Internet,
then type that same user name and
password in here. Your user name looks
something like “jsmith@myisp.com” or
simply “jsmith”. The service name is
optional and is very rarely required by
your ISP. If you don’t know your service
name, leave this blank. When you have
entered your information, click “Next”
to move on.
19
2
1
3
4
5
6
7
8
9
10
section
Connecting and Configuring your Router
3.3 Wireless Setup
This step is optional.
Click “Next” if you want to skip it.
Using this step, you can customize your
wireless network settings if you want
to. Follow the steps on the screen to
complete this step. Click “Next”
to continue.
Step 4 Secure your Network
4.1 After connection has been established,
you will be prompted by the Easy
Install Wizard to select your desired
security level.
4.2 WEP and WPA are the two security
options. If you do not want security or
would prefer to install at a later time,
click the radio button next to “NONE”
and click “Next.”
4.3 The Wi-Fi Protected Access (WPA)
security option features a two-password
setup. You can select one password
that provides COMPLETE NETWORK
access and another password for GUEST
(Internet only) access only. Click “Next”.
4.4 Security setup is now complete. Click
“Next” to configure.
Connecting and Configuring your Router
20
5.1 Checking Internet
The Wizard will now check for an Internet
connection. This can take a few minutes.
The Wizard may not detect a connection
right away. If not, it will retry a number
of times. The “Connected” light on the
front panel of the Router will flash
during this time. Please be patient
through this process.
5.2 Finished
When the Internet connection is
complete, the Wizard will tell you that
you are finished. The “Connected” LED
on the front of the Router will be solid
BLUE, indicating that the Router is now
connected to the Internet.
Your Router is now connected to the Internet.
Now you can begin surfing the Internet by
opening your browser and going to your
favorite web page.
Step 5
Configure the Router
The Wizard will now transfer all of the configuration information to the Router.
This will take approximately one minute. During this time, do not turn off the
Router or computer. The Router will restart itself at the end of this step.
21
2
1
3
4
5
6
7
8
9
10
section
Connecting and Configuring your Router
Congratulations. You have finished installing your new Ativa Router. You
are ready to set up the other computers in your home. You can also add
computers to your Router anytime you want.
Alternate Setup Method
22
The Web-Based Advanced User Interface is a web-based tool that you can use
to set up the Router if you don’t want to use the Easy Install Wizard. You can
also use it to manage advanced functions of the Router. From the Web-Based
Advanced User Interface, you can perform the following tasks:
• View the Router’s current settings and status
• Configure the Router to connect to your ISP with the settings that they
provided you
• Change the current network settings such as the Internal IP address, the
IP address pool, DHCP settings, and more
• Set the Router’s firewall to work with specific applications
(port forwarding)
• Set up security features such as client restrictions, MAC address filtering,
WEP, and WPA
• Enable the DMZ feature for a single computer on your network
• Change the Router’s internal password
• Enable/Disable UPnP (Universal Plug-and-Play)
• Reset the Router
• Back up your configuration settings
• Reset the Router’s default settings
• Update the Router’s firmware
Step 1
Connect your Router
1.1 Turn off the power to your modem by unplugging the power supply from
the modem.
1.2 Locate the network cable that is connected between your modem and
your computer and unplug it from your computer, leaving the other end
connected to your modem.
1.3 Plug the loose end of the cable you just unplugged into the port on the
back of the Router labeled “Modem”.
1.4 Connect a new network cable (not included) from the back of the
computer to one of the wired computer ports labeled “1–4”. Note: It
does not matter which numbered port you choose.
23
2
1
3
4
5
6
7
8
9
10
section
Alternate Setup Method
1.5 Turn your cable or DSL modem on by reconnecting the power supply
to the modem.
Mac or PC computer that was originally connected
to the cable or DSL modem
Network cable
(to computer)
To power adapter
Existing networking cable
(came with modem)
Note: Your Router may have ports in different locations than depicted
in the illustration above.
1.6 Before plugging the power cord into the Router, plug the cord into the
wall, then plug the cord into the Router’s power jack.
1.7 Verify that your modem is connected to the Router by checking the
lights on the front of the Router. The BLUE light labeled “Modem”
should be ON if your modem is connected correctly to the Router. If it
is not, recheck your connections.
1.8 Verify that your computer is connected properly to the Router by
checking the lights labeled “1–4”. The light that corresponds to the
numbered port connected to your computer should be ON if your
computer is connected properly. If it is not, recheck your connections.
Alternate Setup Method
24
Step 2
Set up your Computer’s Network Settings to
Work with a DHCP Server
See the section in this User Manual called “Manually Configuring Network
Settings” for directions.
Step 3
Configure the Router Using the Web-Based
Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based Advanced
User Interface. In your browser, type “192.168.2.1” (you do not need to type
in anything else such as “http://” or “www”). Then press the “Enter” key.
PLEASE NOTE: If you have difficulty accessing the Router’s Web-Based
Advanced User Interface, go to the section entitled “Manually Configuring
Network Settings”.
Logging into the Router
You will see the Router’s home page in your browser window. The home page
is visible to any user who wants to see it. To make any changes to the Router’s
settings, you have to log in. Clicking the “Login” button or clicking on any one
of the links on the home page will take you to the login screen. The Router
ships with no password entered. In the login screen, leave the password blank
and click the “Submit” button to log in.
25
2
1
3
4
5
6
7
8
9
10
section
Alternate Setup Method
Logging out of the Router
One computer at a time can log into the Router for the purposes of making
changes to the settings of the Router. Once a user has logged in to make
changes, there are two ways that the computer can be logged out. Clicking the
“Logout” button will log the computer out. The second method is automatic.
The login will time out after a specified period of time. The default login
time-out is 10 minutes. This can be changed from 1 to 99 minutes. For more
information, see the section in this manual entitled “Changing the Login
Time-Out Setting”.
Using the Web-Based Advanced User Interface
The home page is the first page you will see when you access the Web-Based
Advanced User Interface (UI). The home page shows you a quick view of the
Router’s status and settings. All advanced setup pages can be reached from
this page.
(1)
(10) (2) (5) (4) (3)
(9)
(8)
(7)
(6)
1. Quick-Navigation Links
You can go directly to any of the Router’s UI pages by clicking directly
on these links. The links are divided into logical categories and grouped
by tabs to make finding a particular setting easier to find. Clicking on
the purple header of each tab will show you a short description of the
tab’s function.
Loading...