FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class B digital service, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. Any changes or modifications made to
this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
CE Warning: This device complies with the essential requirements of the
R&TTE Directive 1999/5/EC. The following test methods have been applied
in order to prove presumption of conformity with the essential requirements of
the R&TTE Directive 1999/5/EC:
EN 60065
Safety of Information Technology Equipment
EN 50371
Generic standard to demonstrate the compliance of low power electronic and
electrical apparatus with the basic restrictions related to human exposure to
electromagnetic fields (10 MHz - 300 GHz) -- General public
EN 301 893
ii
VE819 User Manual
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN;
Harmonized EN covering essential requirements of article 3.2 of the R&TTE
Directive
EN 301 489-1
Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
RoHS
This product is RoHS compliant.
iii
VE819 User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
Internationalhttp://eservice.aten.com
Telephone Support
For telephone support, call this number:
International886-2-8692-6959
China86-400-810-0-810
Japan81-3-5615-5811
Korea82-2-467-6789
North America1-888-999-ATEN ext 4988
United Kingdom44-8-4481-58923
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
iv
VE819 Package Contents
VE819
1 VE819 HDMI Dongle Wireless Transmitter
1 VE819R HDMI Wireless Receiver
1 Mini USB to USB Cable
2 Mini USB Power Adapters
1 HDMI Cable
1 IR Receiver Cable
1 User Instructions
1 Warranty Card
1 Remote Control Unit with 2AAA Batteries
VE819 Transmitter
1 VE819T HDMI Dongle Wireless Transmitter
1 Mini USB to USB Cable
1 Mini USB Power Adapter
1 User Instructions
1 Warranty Card
VE819 User Manual
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
This User Manual is provided to help you get the most from your system. It
covers all aspects of installation, configuration and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the VE819 system. Its purpose,
features and benefits are presented, and its front and back panel components
are described.
Chapter 2, Hardware Setup, describes how to set up your installation.
Diagrams showing the necessary steps are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the VE819.
Chapter 4, OSD Operation, provides a complete description of the
VE819’s On-Screen Display (OSD), and how to work with it.
Chapter 5, Additional Transmitters, Provides an easy step by step guide
to adding additional transmitters.
An Appendix, provides specifications and other technical information
regarding the VE819.
vii
VE819 User Manual
Conventions
This manual uses the following conventions:
MonospacedIndicates text that you should key in.
[ ]Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1.Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
open the Start menu, and then select Run.
Indicates critical information.
Product Information
→ Run means to
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
Internationalhttp://www.aten.com
North Americahttp://www.aten-usa.com
viii
Chapter 1
Introduction
Overview
The VE819 HDMI Dongle Wireless Extender is a wireless solution that can
extend crystal clear image quality from laptops, DVD players, projectors and
other HDMI Devices to HDMI displays, making it perfect for home, office or
school. It is capable of streaming full 1080p resolution with 5.1 digital audi o
support and 3D technology up to 10m* (33 ft.). A total of three extra
transmitters can be paired with the receiver; allowing users to have four source
devices paired concurrently. Users can switch between source devices from the
receiver side using the IR remote control. By simply connecting the transmitter
and receiver to the HDMI source and display with no hardware setup, this
allows you to control and design you own custom wireless entertainment space.
Note: Distance, quality and signal may vary depending on the environment;
solid structures, such as steel, concrete and brick may result to shorter distance
coverage or complete loss of signal.
1
Chapter 1 Introduction
Features
Wireless transmission of fully uncompressed HD videos up to 30ft.*
(10m)
Allows you to switch and independently select any of sources. When
additional transmitters are connected
Supports full uncompressed 1080p HD resolutions, 3D, and 5.1 channel
digital audio
Superior video quality – 480p, 720p, 1080i, 1080p
Based on WHDI™ technology – Low latency < 1 ms. WHDI enables
delivery of uncompressed high-definition digital video over a wireless
radio channel connecting any video source to any compatible display
device.
HDCP compatible
Plug and Play, no software or driver installation needed
Add up to 4 Wireless HDMI Transmitters
Note:
Distance, quality and signal may vary depending on the environment; solid
structures, such as steel, concrete and brick may result to shorter distance
coverage or complete loss of signal.
Additional wireless transmitters are sold separately.
2
Requirements
Display
A display device with an HDMI Type A input connector
Sources
A source player with an HDMI Type A output connector
VE819 User Manual
3
Loading...
+ 24 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.