ATEN SN3101 Quick Start Guide

Online Registration

International:

ATEN Altusen

SN3101 Serial Device Server Quick Start Guide

© Copyright 2020 ATEN® International Co., Ltd. www.aten.com Altusen and the Altusen logo are trademarks of ATEN International Co., Ltd. All rights reserved. All other trademarks are the property of their respective owners.

This product is RoHS compliant PAPE-1214-Z01G Printing Date: 08/2020

All information, documentation, firmware, software utilities, and specifications contained in this package are subject to change without prior notification by the manufacturer. Please visit our website http://www.aten.com/download/?cid=dds for the most up-to-date versions.

™

• http://support.aten.com

North America:

• http://www.aten-usa.com/product_registration

Technical Phone Support

International:

• 886-2-8692-6959

China:

• 86-10-5255-0110

Japan:

• 81-3-5615-5811

Korea:

• 82-2-467-6789

North America:

• 1-888-999-ATEN Ext: 4988

United Kingdom:

• 44-8-4481-58923

1. Power LED

2. Link LED

3.10/100 Mbps Data LED

4. Tx/Rx (ACT) LED

5. Grounding Terminal

6. Serial Port

7. Reset Switch

Hardware Review (Front View)

1 2 3 4

For flexibility and convenience, the SN3101 can be wall mounted or DIN rail mounted, as

described in the sections that follow.

Mounting

Wall Mounting

To wall mount the SN3101:

1. Use the smaller screws supplied with the Mounting Kit to screw the mounting brackets into

the back of the unit:

Note: If you use third party screws, the length of the shank (the threaded portion) must not

exceed 4.50 mm.

1 SN3101 Serial Device Server

1 Power Adapter

1 DC Terminal Connector

1 Mounting Kit

Package Contents

1 User Instructions

Important Notice

Considering environmental protection, ATEN does not provide a fully printed user manual for this product. If the information contained in the Quick Start Guide is not enough for you to configure and operate your product, please visit our website www.aten.com, and download the full user manual.

Restrictions and Requirements

1. DC Terminal

2. DC Jack

3. LAN Port

5 6

Hardware Review (Rear View)

2. Screw the mounting brackets to the wall.

DIN Rail Mounting

To mount the SN3101 on a DIN rail:

1. Screw the mounting brackets to the back of the SN3101 as described in step 1 of the wall

mounting procedure.

2. Use the larger screws supplied with the Mounting Kit to screw the DIN rail brackets to the

mounting brackets – as shown in the diagram, below:

• Java Runtime Environment (JRE) 8 or later must be installed on your computer. You can download JRE from the website: https://java.com

• The devices that connect to the SN3101 must support one of the following serial protocols:

• RS-232 (protocol or terminal operations)

• RS-422

• RS-485

• To have Virtual COM mode applied to your application, make sure you have Real COM Port drivers (for Windows) or TTY drivers (for Linux) installed. Refer to SN3101's product page for information such as user manual, driver, firmware, and MIB file.

Scan for more information

1 2 3

3. Hang the unit on the DIN Rail.

Hardware Installation

Operation

Specifications

To install the SN3101, do the following:

1. If you intend to use the DC terminal, screw the DC terminal connector to the block – as

shown in the following diagram

Refer to the Installation diagram as you do the following:

a. Use a null modem cable to connect the SN3101's serial port to your serial device.

b. Ground the device.

c. Plug the cable that connects the SN3101 to the network or the Internet into the LAN port.

d. Connect the DC power source to the device.

SN3101 Installation Diagram:

SN3101

Serial Device

Logging In

SN3101 operation is Internet browser based. To begin:

1. Open your browser and specify the IP address of the SN3101 you want to access in the

browser's URL location bar.

Note: If you are logging in for the first time, use SN3101’s default IP address:

192.168.0.60.

2. A Security Alert dialog box appears. Accept the certificate.

3. A login dialog box, like the one below, appears:

4. Provide a valid Username and Password (set up by the administrator), then Click Login to

continue.

Note: If you are the administrator, and are logging in for the first time, use the default

Username: administrator; and the default Password: password. For security

purposes, we strongly recommend you change these and give yourself a unique

Username and Password.

After you have successfully logged in, the Main Screen appears:

Function Speciﬁcation

Serial 1 x DB-9 M (Black)

Connectors

Switches Reset 1 x Semi-recessed Pushbutton

LEDs

Power Input

Power Consumption 9V, 2.7W

Interfaces

Regulatory Approval FCC Class A, CE Class A, RoHS

Environment

Physical Properties

Network 1 x RJ-45 (Black)

Power

Power 1 x Green

Link 1 x Green

10/100 Mbps 1 x Orange/Green

TxRx (ACT) 1 x Green

PWR1 12-48V DC (2-pin Terminal Block)

PWR2 9-30V DC (Power Adapter Jack)

Power Adapter 100-240V AC; 50–60 Hz

Power Line Protection

Serial

Network

Operating Temp. 0-60

Storage Temp. -20-85

Humidity 0-95% RH , Non-condensing

Housing Metal

Weight 0.22 kg

Dimensions (L x W x H) 10.69 x 7.90 x 2.44 cm

PWR1 1 x 2-pin Terminal Block (Green)

PWR2 1 x DC Jack (Black)

4KV burst (EFT), EN61000-4-4 2KV surge, EN61000-4-4

Standards RS-232/422/485; Software selectable

Baud Rate 460Kbps

RS-232 Signals TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND

RS-422 Signals Tx+, Tx-, Rx+, Rx-, RTS+, RTS-, CTS+, CTS-, GND

RS-485 Signals Data+, Data-, GND

Serial Protection 15 KV ESD Protection for the serial port

Parity None, Even, Odd, Mark, Space

Data Bits 5, 6, 7, 8

Stop Bits 1,1,5,2

Flow Control None, XON/XOFF, RTS/CTS

Standards 10/100BaseTX; Autosensing

Protection 1.5 KV Magnetic Isolation

Protocols

ARP, DHCP, DNS, HTTP, HTTPS, ICMP, IP, TCP, UDP, NTP, PPP, RADIUS, Telnet, SNMP, SNMP Trap, SMTP, SSH

12 – 48V