ATEN PE1216G, PE1324G User guide

eco PDU PE Series

SNMP Settings

User Instructions

www.aten.com

NRGence User Help

 Set the maximum permissible breaker protection in the building circuitry to the

current rating specified on the rating plate. Observe all national regulations and
safety codes as well as deviations for breakers.

 Only connect the PE Device to a grounded power outlet or a grounded system!
 Make sure that the total current input of the connected systems does not exceed

the current rating specified on the rating plate of the PE Device.

 There is a risk of explosion if the battery is replaced with an incorrect type.

Dispose of used batteries according to the relevant instructions.

User Information

Online Registration

Be sure to register your product at our online support center:

International http://support.aten.com

North America http://www.aten-usa.com/product_registration

Telephone Support

For telephone support, call this number:

International 886-2-8692-6959

China 86-10-5255-0110

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

United Kingdom 44-8-4481-58923

User Notice

All information, documentation, and specifications contained in this manual are subject to change
without prior notification by the manufacturer. The manufacturer makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the
manufacturer's software described in this manual is sold or licensed as is. Should the programs
prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its
dealer), assumes the entire cost of all necessary servicing, repair and any incidental or
consequential damages resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV interference caused by
unauthorized modifications to this device. It is the responsibility of the user to correct such
interference.

The manufacturer is not responsible for any damage incurred in the operation of this system if the
correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT
THE VOLTAGE SETTING IS CORRECT BEFORE USE.

PE Device Safety Notice

ii

Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Eco PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

SNMP Trap Receivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Eco Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

SNMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Synchronizing SNMP Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

MIB Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Set SNMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Setting Up Thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting Device/Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Reading Device/Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

SNMP

iii

Configuring SNMP

Introduction

This guide helps you to set up your PE series eco PDU and NRGence eco
Sensors software for use with an SNMP manager.With support for SNMP V1,

V2C and V3, your PE system can be configured to receive Set/Get commands
in order to retrieve status updates and configure some basic settings (such as
thresholds), as well as send traps to an SNMP manager.

In order to utilize SNMP functionality in your PE installation, it is important
that all the parameters outlined in the following sections are synchronized for
all eco PDUs in your installation. See Synchronizing SNMP Parameters,
page 6, for further details.

There are three ways to utilize SNMP functionality with your NRGence
device:

 with the device’s built-in graphical user interface (GUI)

 with eco Sensors power management software

 with a MIB browser

These are detailed in the following sections.

1

NRGence SNMP User Help

eco PDU

Graphical User Interface (GUI)

To configure the SNMP settings on an individual eco PDU via its graphical
user interface (GUI), access the unit’s Device Management page, shown
below:

Note: Reference your eco PDU User Manual for full details about accessing

the unit’s Graphical User Interface via a Web browser.

The Device Management page allows super administrators, administrators, and
users with device management permission to configure and control overall eco
PDU operations. To configure the SNMP settings, click on the Device
Configuration tab, and open the Event Notification section.

The Event Notification section is divided into four sections: SMTP Settings;
Log Server; SNMP Trap Receivers; and Syslog Server. Scroll down to the
SNMP Trap Receivers section, as shown below:

2