FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
Warning: Operation of this equipment in a residential environment could
cause radio interference.
Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann
Funkstörungen verursachen.
KCC Statement
RoHS
This product is RoHS compliant.
ii
ES0152/ES0152P User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
Internationalhttp://eservice.aten.com
Telephone Support
For telephone support, call this number:
International886-2-8692-6959
China86-400-810-0-810
Japan81-3-5615-5811
Korea82-2-467-6789
North America1-888-999-ATEN ext 4988
1-949-428-1111
User Notice
All information, documentation, and specifications contained in this manual are subject
to change without prior notification by the manufacturer. The manufacturer makes no
representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties as to merchantability or fitness for any
particular purpose. Any of the manufacturer's software described in this manual is sold
or licensed as is. Should the programs prove defective following their purchase, the
buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of
all necessary servicing, repair and any incidental or consequential damages resulting
from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference
caused by unauthorized modifications to this device. It is the responsibility of the user
to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this
system if the correct operational voltage setting was not selected prior to operation.
PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.
Altusen and the Altusen logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
Package Contents
ES0152
1 52-Port GbE Managed Switch
1 AC Power Cord
1 RJ-45 to DB-9 Serial Console Cable
1 Mounting Kit
1 Foot Pad Set (4 pcs.)
1 User Instructions*
ES0152P
1 52-Port GbE (PoE) Managed Switch
1 AC Power Cord
1 RJ-45 to DB-9 Serial Console Cable
1 Mounting Kit
1 Foot Pad Set (4 pcs.)
1 User Instructions*
Check to make sure that all of the components are present and in good order.
If anything is missing, or was damaged in shipping, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the switch or to any other
devices on the installation.
* Features may have been added since this manual was published. Please visit
our website to download the most up to date version of the manual.
This User Manual provides specific information about using the web interface
to operate this switch.
Overview
Chapter 1, Introduction, introduces you to the 52-Port GbE (PoE) Managed
Switch. Its purpose, features and benefits are presented, its front and rear panel
components are described, and how to access the web interface.
Chapter 2, Installation, provides hardware instructions for setting up your
switch.
Chapters 3-17, are the side menu of the web interface and their
corresponding configurations/operations.
Chapter 18, Device Management System (DMS), explains the DMS
intelligent management tool and the information to help you manage the
switch.
An Appendix, at the end of the manual provides technical and
troubleshooting information.
xii
ES0152/ES0152P User Manual
Conventions
This manual uses the following conventions:
MonospacedIndicates text that you should key in.
[ ]Indicates keys you should press. For example, [Enter] means
1.Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential
→ or >Indicates selecting the option (on a menu or dialog box, for
to press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
steps.
example), that comes next. For example, Start
to open the Start menu, and then select Run.
Indicates critical information.
→
Run means
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the W eb for a list of locations and telephone numbers:
Internationalhttp://www.aten.com
xiii
ES0152/ES0152P User Manual
This Page Intentionally Left Blank
xiv
Chapter 1
Introduction
Overview
The ES0152 / ES0152P is a feature-rich managed switch for ATEN KE series
KVM over IP extenders and VE89 series Video over IP extenders*. Ideal for
installation in combination with the KE / VE89 series products, the ES0152 /
ES0152P helps users build their OT infrastructure with the KE series by
eliminating the hassles of complicated setup.
Deploying the ES0152 / ES0152P is fast and easy. With everything plug and
play, there is no need to install software or configure devices. Simply connect
the KE / VE89 transmitters and receivers to the ES0152 / ES0152P using Cat
5e/6 cables and all KE / VE89 series devices on the same LAN will
automatically be detected.
The ES0152 / ES0152P network switch provides a 52-port, high-performance
configuration, a complete array of L2 features and advanced functionalities
including Layer 3 static route, DHCP server, IPv6 support and LLDP,
delivering a versatile solution for improving network performance.
Both the ES0152 and the ES0152P offer a combination of SFP+ (fiber) and
RJ45 (copper) ports for servicing a range of network needs. The ES0152
delivers 4 (1G/10G) SFP+ and 48 (10M/100M/1G) RJ45 ports while the
ES0152P supports 4 (1G/10G) SFP+ and 48 (10M/100M/1G) RJ45 with PoE+
(Support 802.3at/af) ports. Featuring Power over Ethernet (PoE) function, the
ES0152P can provide up to 740 Watts power budget across 48 RJ45 ports thus
eliminating the need for a power adapter and effectively reducing the power
configuration cost.
The ES0152 / ES0152P comes with embedded DMS functions to facilitate
device management anytime and anywhere. Its intuitive, user-friendly
interface enables IT administrators to set up and manage their networks and all
the connected KE / VE89 devices effortlessly. It also has comprehensive
security features such as IP source guard and ACL to guard your network from
unauthorized access.
With a full range of functions to help with optimizing network efficiency,
manageability and reliability for their network environment, the ES0152 /
ES0152P is an ideal network switch solution for SMBs and enterprises, and
even more so for those that have chosen to adopt ATEN KE series KVM over
1
KVM over IP User Manual
IP extenders or VE89 series Video over IP extenders into their OT
infrastructure.
Note: Please visit www.aten.com for compatible products.
2
Chapter 1. Introduction
Features
Auto detects KE/VE89 series devices
Plug-and-play without additional settings
Supports IGMP Snooping Fast Leave
Supports Flow Control
Supports IGMP v1/v2/v3 Snooping and IGMP v1/v2 Querier
High-performance Gigabit Ethernet L2 access switch with 176 Gbps
switching capacity - significantly improve the responsiveness of
applications and file transfer times
Built in Device Management System (DMS) to provide an overview of all
connected KE/VE89 devices for management
Supports IEEE 802.1w Rapid Spanning Tree Protocol – ensuring a faster
recovery from failed links and enhancing overall network stability and
reliability
Comprehensive QoS – allowing the marking, classification, and
scheduling of up to four traffic types across the network
Enhanced Security - Port Security limits the total number of devices using
a switch port and protects against MAC flooding attacks
IPv4/IPv6 Management
802.3af PoE/ 802.3at PoE+ Port configuration and scheduling (ES0152P
only)
3
KVM over IP User Manual
Components
ES0152 Front View
ES0152P Front View
No.ComponentES0152P
1System LEDIndicates if the switch is powered up correctly or not, or,
2Link/Act/Spd
LED
(ES0152P Only)
3PoE LED
(ES0152P Only)
4
indicates if there is a system alarm triggered for
troubleshooting.
Refer to System LED on page 5 for the behavior of the LED.
When this LED is lit, the port status LEDs are displaying the
link status, network activity and speed of each port. Refer to
Port Status LED on page 6 for the behavior of the LED.
Users can press the Mode button to toggle between Link/
Activity/Speed mode and PoE mode.
When this LED is lit, the port status LEDs are displaying PoE
powering status of each port. Refer to Port Status LED on
page 6 for the behavior of the LED.
Users can press the Mode button to toggle between Link/
Activity/Speed mode and PoE mode.
Chapter 1. Introduction
No.ComponentES0152P
4Mode/Reset
Button
510/100/1000 RJ-
45 Ports
6Port Status LEDs Indicates the status of the connected port. Refer to Port
710G SFP+ Ports
8Console PortConnect RJ-45 to DB-9 Serial Console Cable for CLI
By pressing the Mode/Reset Button for a different period of
time, users can reset the switch, restore the switch to factory
defaults, or change the display definition of port status LEDs
(ES0152P only):
Restore to default: Press and hold the button for 7-12
seconds. The system LED will start blinking while all port
status LEDs will stay on.
Reset the switch: Press and hold the button for 2-7
seconds. The system LED will start blinking while all port
status LEDs will turn off.
(ES0152P only) Change port status LEDs definition:
Press and hold the button for 0-2 seconds. The system LED
will turn on while the port status LEDs will behave according
to Port Status LED on page 6.
Status LED on page 6 for more details.
operation. Refer to the CLI User Manual for the CLI
commands.
System LED
ColorStateDescription
Green
RedOn
OnThe switch is powered ON correctly.
OffThe switch is not receiving power.
An abnormal state, such as exceeding operating
temperature range, has been detected in the switch.
5
KVM over IP User Manual
Port Status LED
The port status LED behavior is shown in the following table:
PortColorStateDescription
The port is enabled and established a link to
connected device, and the connection speed is
1000Mbps.
The port is transmitting/receiving packets, and
the connection speed is 1000Mbps.
The port is enabled and established a link to
connected device, and the connection speed is
10/100Mbps.
The port is transmitting/receiving packets, and
the connection speed is 10/100Mbps.
The port has no active network cable connected,
or it has not established a link to the connected
device. Otherwise, the port may have been
disabled through the switch user interface.
The port is enabled and established a link to
connected device, and the connection speed is
10Gbps.
The port is transmitting/receiving packets, and
the connection speed is 10Gbps.
The port is enabled and established a link to
connected device, and the connection speed is
1Gbps.
The port is transmitting/receiving packets, and
the connection speed is 1Gbps.
The port has no active network cable connected,
or it has not established a link to the connected
device. Otherwise, the port may have been
disabled through the switch user interface.
RJ45
Ports
SFP+
Ports
GreenOn
GreenBlinking
AmberOn
AmberBlinking
--Off
BlueOn
BlueBlinking
GreenOn
GreenBlinking
--Off
When Link/Act/Speed LED is Lit (ES0152P only)
The behavior of the port status LED is the same as the table above.
6
When PoE LED is Lit (ES0152P only)
PortColorStateDescription
The port is enabled and supplying power to the
connected device.
An abnormal state, such as overload status, that
has been detected in the switch.
The port has no active network cable connected,
or it is not connected a PoE PD device.
Otherwise, the port may have been disabled
through the switch user interface.
RJ45
Ports
GreenOn
AmberOn
--Off
Chapter 1. Introduction
7
KVM over IP User Manual
ES0152 / ES0152P Rear View
No.ComponentDescription
1 Power Connector Connect the provided power cord to this socket and an AC wall
power socket to power the device.
8
Chapter 1. Introduction
Web Interface
The features and functions of the switch can be configured and managed via
the web interface, which are laid out in the chapters starting from Chapter 3
System.
Initial Configuration and Logging In
When powering up the switch for the first time, you can perform the initial
switch configuration using the web interface.
To begin with the initial configuration stage, you need to reconfigure your PC’s
IP address and subnet mask to allow communication between your PC and the
switch.
Factory default IP Address of the switch: 192.168.0.1
Factory default Subnet Mask of the switch: 255.255.255.0
Factory default Gateway of the switch: 192.168.0.254
After changing your PC’s IP address (for example, 192.168.0.250), you can
access the Web interface of the switch using the switch’s default IP address
(192.168.0.1).
The initial switch configuration procedure example, for a PC running
Windows® 7/8.x/10, is as follows:
1. Type “network and sharing” into the Search box in the Start Menu.
2. Select Network and Sharing Center.
3. Click on Change adapter settings on the left of PC screen.
Note: Users can also skip step 1 to 3, by pressing WinKey+R and type
“ncpa.cpl” command to get to step 4 directly.
4. Right-click on your local adapter and select Properties.
5. In the Local Area Connection Properties window highlight Internet
Protocol Version 4 (TCP/IPv4) then click the Properties button.
Note: Record all your PC’s current IP settings to be able to restore them later.
6. Select the radio button Use the following IP address and enter the IP for
the PC (e.g. any IP address not in use, and in between 192.168.0.2 and
192.168.0.254), Subnet mask (e.g. 255.255.255.0), and Default gateway
9
KVM over IP User Manual
that corresponds to your network setup. Then enter your Preferred and
Alternate DNS server addresses.
7. Click OK to change the PC’s IP address.
8. Open a web browser on the PC and enter the factory default IP address to
access the switch’s web interface. A login page appears:
Note: If you do not see the above login page, please try the following:
1. Refresh the web page.
2. Check to see if there is an IP conflict issue.
3. Clean browser cookies and temporary internet files.
4. Check your PC settings again and repeat step 2.
9. Enter the username and password. The default username is admin. A
preprogrammed password (inside the red square box below) unique to
each switch is provided on the sticker of the bottom side of the switch. An
example is shown:
10
Chapter 1. Introduction
10. Click “Login” to log into the switch.
Note: If you wish to change the password, go to Security > Management
> Account and click admin (name of user). Enter the new
password, repeat it and click Apply.
11
KVM over IP User Manual
This Page Intentionally Left Blank
12
Chapter 2
Installation
Mounting
Rack Mount
Follow the steps below to rack mount the device.
1. Attach the mounting brackets to both sides of the chassis. Insert screws
and tighten then with a screwdriver to secure the brackets.
2. Place the switch on a rack shelf in the rack. Push it in until the oval holes
in the brackets align with the mounting holes in the rack posts.
3. Attach the brackets to the posts. Insert screws and tighten them.
13
KVM over IP User Manual
Desk Mount
1. It is recommended to verify that the desk/bench is sturdy for the device to
be mounted on and that it is reliably grounded.
2. Attach the four adhesive rubber feet to the bottom of the switch.
14
Chapter 2. Installation
Installing SFP+ Modules
As an option accessory for the SFP+ ports, you can install a mini-GBIC SFP+
module. Since the connection capability of the SFP+ ports is up to 10Gbps, you
can choose mini-GBIC SFP+ modules able to support data rates of up to
10Gbps. You can install the module even while the switch is powered.
1. Insert the module into the SFP+ port.
2. Press firmly to ensure that the module seats into the connector.
15
KVM over IP User Manual
Hardware Installation
Connect the power cord between the ES0152 / ES0152P's power socket and an
AC source, check the system LED if the switch is powered on. Connect an
Ethernet LAN cable between the switch's RJ-45 port and the Ethernet RJ-45
port on the KE / VE89 Series extenders. If the port status LED is blinking, the
switch is ready.
An example is shown:
16
Loading...
+ 450 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.