ATEN CN-6000 User Manual
User Manual
CN-6000
2003-11-14
Warning!
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user
may be required to take adequate measures.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
2003-11-14
CN-6000 User Manual
Packing List
The complete CN-6000 package consists of:
M 1 CN-6000 KVM On the Net Control Unit
M 1 CS Custom KVM Cable Set
M 1 Power Adapter
M 1 Rack Mount Kit
M 1Software CD
M 1 User Manual
M 1 Quick Start Guide
Check to make sure that all the components are present and that nothing was
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation procedures
carefully to prevent any damage to the unit, and/or any of the devices connected
to it.
© Copyright 2003 ATEN® International Co., Ltd.
Manual Part No. PAPE-0227-1AT
Printed in Taiwan 10/2003
All brand names and trademarks are the registered property of their respective owners.
2003-11-14
iii
CN-6000 User Manual
Contents
1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Hardware Setup
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. The Administrator Utility
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Settings Notebook . . . . . . . . . . . . . . . . . . . . . . . . . 14
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Uploading Changes . . . . . . . . . . . . . . . . . . . . . . . . 14
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
User Management . . . . . . . . . . . . . . . . . . . . . . . . . 21
Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Upgrading the Firmware and Java Program . . . . . . . . . . . . . . 24
Java Authentication Page . . . . . . . . . . . . . . . . . . . . . . . . 26
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. The Windows Client
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
The Connection Screen . . . . . . . . . . . . . . . . . . . . . . 30
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
iv
2003-11-14
CN-6000 User Manual
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
The Hotkey Setup Screen . . . . . . . . . . . . . . . . . . . . . 33
Configuring the Hotkeys . . . . . . . . . . . . . . . . . . . . . 34
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . 35
Keystrokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Mouse Synchronization . . . . . . . . . . . . . . . . . . . . . . 36
Video Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 38
Work Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5. The Java Client
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
The Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . 46
The User Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6. The Log Server
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
The Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
The CN-6000 List Panel . . . . . . . . . . . . . . . . . . . . . . . . 57
The Event List Window . . . . . . . . . . . . . . . . . . . . . . . . 58
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Appendix
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2003-11-14
v
CN-6000 User Manual
About This Manual
This User Manual is provided to help you get the most from your CN-6000 system.
It covers all aspects of installation, configuration and operation. An overview of
the information found in the manual is provided below.
Overview
Chapter 1, Introduction, introduces you to the CN-6000 System. Its purpose,
features and benefits are described.
Chapter 2, Hardware Setup, prese nts the front and back panel components,
and explains how to connect the CN-6000 to your server or KVM switch and the
Internet.
Chapter 3, The Administrator Utility, explains how to connect to the
CN-6000 as an administrator; and how to configure the CN-6000 for operation.
Chapter 4, The Windows Client, explains how to run the Windows Client
Software; how to connect to the CN-6000 and how to remotely control the
connected server (or servers via a KVM switch).
Chapter 5, The Java Client, explains how to run the Java Client Software;
how to connect to the CN-6000 and how to remotely control the connected server
(or servers via a KVM switch).
Chapter 6, The Log Server, is a Windows-based administrative utility that
records all the events that take place on selected CN-6000 units and stores them
in a searchable database.
An Appendix at the end of the manual provides specifications and other
technical information regarding the CN-6000.
An Index follows the Appendix for convenient reference to the manual’s
information.
vi
2003-11-14
CN-6000 User Manual
Conventions
This manual uses the following conventions:
Courier Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
M Bullet lists provide information
> Indicates selecting an option on a menu. For example, Start > Run
means to open the Start menu, and then select Run.
Indicates critical information.
2003-11-14
vii
CN-6000 User Manual
Notes:
viii
2003-11-14
Chapter 1.
Introduction
Overview
The CN-6000 is a control unit that allows operators to monitor and access their
computers from remote locations. The CN-6000 connects to the Internet, an
Intranet, LAN, or WAN using industry standard Category 5 cable, then uses KVM
cable to connect to a local KVM switch or server.
Since the CN-6000 uses TCP/IP for its communications protocol, the server or
KVM switch it is connected to can be accessed from any computer on the Net whether that computer is located down the hall, down the street, or half-way
around the world.
Operators at remote locations connect to the CN-6000 via its IP address. Once a
connection has been established and authorization granted, operators of the remote
computer can exchange keyboard, video and mouse signals with the server (or
servers on a KVM switch installation), just as if they were present locally and
working on the equipment directly.
2003-11-14
KVM Switch
1
CN-6000 User Manual
With its advanced security features, the CN-6000 is the fastest, most reliable, most
cost effective way to remotely access and manage widely distributed multiple
computer installations.
The Administrator and Client software utilities provided with the CN-6000 make
it easy to install, maintain, and operate. System administrators can handle a
multitude of tasks with ease - from installing and running GUI applications, to
BIOS level troubleshooting, routine monitoring, concurrent maintenance, system
administration, rebooting and even pre-booting functions.
The Administrator Utility is used to: configure the system; limit access from
remote computers; manage users; and maintain the system with firmware and
software module updates.
Both a Windows GUI Client and a Java Client are provided for IP connection and
login from anywhere on the net. Inclusion of a Java-based client ensures that the
CN-6000 is platform independent, and is able to work with all operating systems.
The CN-6000’s client software allows access to, and control of, the connected
servers. Once an operator successfully connects and logs in, his screen displays
what is running on the remote unit attached to the CN-6000 (a KVM OSD display,
a server’s desktop, or a running program, for example) and he can control it from
his console just as if he were there.
The Log Server records all the events that take place on selected CN-6000 units
for the administrator to analyze.
Your CN-6000 investment is protected by a Firmware Upgrade Utility. You can
stay current with the latest functionality improvements by downloading firmware
update files from our website as they become available, and then using the utility
to quickly and conveniently perform the upgrade.
2
2003-11-14
Introduction
Features
M Remote access of KVM switches or servers via LAN, WAN, or the Internet;
control your installation from down the hall, down the street, or half-way
around the world
M Supports 10Base-T, 100Base-T, TCP/IP, HTTP
M Advanced security features include password protection and advanced
encryption technologies
M High video resolution: up to 1280 x 1024 @ 75Hz; 1600 x 1200 @ 60Hz
M Windows GUI and Java-based client software; Java client works with all
operating systems
M Upgradeable firmware via RJ45 Ethernet connection (with default F/W)
M Supports unlimited user accounts
System Requirements
M For best results we recommend that the computers used to access the
CN-6000 control unit have at least a P III 1 GHz processor, and that the
screen resolution is set to 1024 x 768.
M For the Windows Client, you must have DirectX 7.0 or higher installed.
M For the Java Client, you must have Sun’s Java 2 (IBM Java 1.3 or higher).
M For the Log Server, you must have the Microsoft Jet OLEDB 4.0 or higher
driver installed.
3
2003-11-14
CN-6000 User Manual
Notes:
4
2003-11-14
Chapter 2.
Hardware Setup
Front View
1
2
3
4
1. Reset / Firmware Upgrade Switch
M Pressing and holding this switch in while powering On the CN-6000 puts
the switch into Firmware Upgrade mode.
M Pressing and holding this switch in for more that two seconds performs a
system reset.
Note: This switch is recessed and must be pushed with a thin object - such
as the end of a paper clip, or a ballpoint pen.
2. 10/100 Mbps Data LED
M The LED lights GREEN to indicate 10 Mbps data transmission speed.
M The LED lights ORANGE to indicate 100 Mbps data transmission speed.
3. Link LED
Flashes GREEN to indicate that a Client program is accessing the device.
4. Power LED
Lights when the CN-6000 is powered up and ready to operate.
5
2003-11-14
CN-6000 User Manual
Rear View
1
2
3
4
1. KVM Port
The KVM cable (supplied with this package) that links the CN-6000 to
your KVM switch or server plugs in here.
2. Local Console Section
The CN-6000 can be accessed via a local console as well as over the Net.
The cables for the local console (keyboard, monitor, and mouse) plug in
here. Each port is color coded and marked with an appropriate icon to
indicate itself.
5
3. RJ-45 Jack
The cable that connects the CN-6000 to the Internet server plugs in here.
4. RS-232 Port
The RS-232 port is reserved at this time.
5. Power Jack
The power adapter cable plugs in here.
6
2003-11-14
Hardware Setup
Installation
1. Before you begin, make sure that power to all the devices you will
be connecting up have been turned off. You must unplug the power
cords of any computers that have the Keyboard Power On function.
2. To prevent damage to your installation, make sure that all devices
on the installation are properly grounded.
To install the CN-6000, refer to the diagram below (the diagram numbers correspond to the numbered steps), and do the following:
1. Plug the local administrator’s keyboard, mouse, and monitor in to th e unit’ s
Console Ports.
2. Use the KVM cable provided with this package to connect the CN-6000’s
KVM Port, to the Keyboard, Video and Mouse ports of the server or KVM
switch that you are installing.
3. Plug the LAN or WAN cable into the CN-6000’s RJ-45 socket.
4. Plug the power adapter cable into the CN-6000’s power jack, then plug the
power adapter into an AC power source.
5. Power up your server or KVM installation.
4
2
KVM Switch
1
3
7
2003-11-14
CN-6000 User Manual
Notes:
8
2003-11-14
Chapter 3.
Getting Started
Logging In
Operation of the CN-6000 is browser based. To begin, open your browser and
specify the CN-6000’s IP address in the browser’s URL location bar. For example:
http://100.0.0.001
The CN-6000 login page appears:
2003-11-14
9
Loading...