Atek INC 210 User Manual

1

Signal

M12 Socket

Cable

V+ (12..24VDC)

Pin 1

Red

Output 1 (0.1-10VDC / 4-20mA) (X axis)

Pin 2

Yellow

GND (0V)

Pin 3

Black

Output 2 (0.1-10VDC / 4-20mA) (Y axis)

Pin 4

Green

Reset

Pin 5

Pink

 The installation of the product is carried out by the customer who purchases the product, according to the wiring diagrams,

There must be minimum distance between the sensor and control unit. Avoid additions except the suitable connector unless

Keep away the sensor cable from as high power energy cables, contactor, motor, switched power supplies, inductive and

Not to damage the sensor, supply directions and voltage must be paid attention. Don’t energize before all connections

Transport and storage should be at their original packaging and an ambient temperature of -30°C / +70°C in such a way that

Chemicals such as alcohol, thinner etc. should not be used for cleaning the product. The product should be wiped with a

INC 210 (Analog Output)

ANGLE SENSOR USER MANUAL

WARNINGS

ELECTRICAL CONNECTION

DETERMINING THE 0° POINT OF SENSOR

Thus, the sensor

recognizes that the position is 0 °. If the same operation is repeated a second time, the sensor is reset to the factory

During the operations, the sensor position should be kept constant for approximately 4 seconds.

M12 - 5 PIN MALE

* Output 2 is only used on two-axis models. On single-axis models, Pin 4 (green

GENERAL INFORMATIONS

INC 210 series angle sensors are the sensors that show the angle of rotation of objects
standing perpendicular to the earth. Angle measurement information between 0°-360°

20mA current output option, can take measure ment with ±0.1° accuracy. Thanks to its

environments with their high IP protection classes. Optionally, sensors with redundant
output can be produced.

M12 - 5 PIN

FEMALE SOCKET

can be taken from these sensors. These sensors with 0.1-10VDC voltage output or 4-

compensated axis sensitivity, the effect of the axes on each other is minimized.

These sensors, especially used in machine and crane industries, can operate in outdoor

installation information, etc. in this manual.

 Maintenance and repair should be done by the technicians authorized by the manufacturer firm.


it needs.



capacitive noisy supplies.



completed.



they will not be exposed to dust, humudity, impact, vibration, falling or water.



damp cloth.

 The product may be damaged and may become unusable if used outside of the specifications in the user manual.

SOCKET

cable) is empty.
* On single output models, 1 pcs M12 5 pin male socket is used as standard.
* Redundant models have two outputs. 1 pcs M12 5 pin male ve 1 pcs M12 5 pin
female socket is used as standard.
* Different socket models can be requested optionally.

Pin 5 (pink cable) and pin 3 (black cable) are short-circuited for about 2 seconds and then disconnected.

settings.

KK-INC.006 18.01.19 Rev No:1

2

The product must be fixed to the area to be taken inclination

Warning: All welding work in the relevant area must be
completed before the product is installed. Otherwise, the
device may be damaged during the welding process, and in this
case, it will be out of warranty.

0-360⁰

DIMENSIONS (in mm)

MEASUREMENT AXIS AND OUTPUT DIAGRAM

MECHANICAL MOUNTING

Analog Signal Output

measurement with 3 pcs M6 bolts and nuts.

KK-INC.006 18.01.19 Rev No:1

3

Supply Voltage

4-20 mA : 12 … 24 VDC

0-10 VDC: 15 … 24 VDC

Protection Class

IP67

*Measurement

Range

0⁰ … 360⁰

Operating Temperature

- 30°C … +70°C

Relative Humudity

%10 … %90

*Output Signals

Analog 4-20 mA or 0.1-10 VDC
Optional Redundant Output

Weight

~250 gr

Resolution

12 bit

Body Material

Aluminium

Accuracy

±0,1⁰

*Electrical Connection

M12 5 pin (male) socket or cable output

Note: The specifications specified by (*) vary depending on the model selected. The detailed code table for product selection is shown on page 4.

Product

Description

INC 210

Angle Sensor

User Manual

1 pcs.

TECHNICAL SPECIFICATIONS

PRODUCT CODE TABLE

BOX CONTENTS

Supply Voltage

(1)

Sensor Type

Model

Number of axes

Output Signals

A: 4-20 mA

Electrical Connection

(3)

Measurement Range

(2)

180: 0-180°

Output Signal Direction

CCW: Counter-Clockwise

Output Type

(1) The supply voltage is 12…24VDC for 4-20 mA output models, and 15…24VDC for 0-10 VDC output models.
(2) Optionally, different measurement values between 0-360° can be requested. You should specify your non-standard measurement

(3) The product can be requested with cable or socket.

INC 210 series, angle, single axis, 0-360° measurement, 12-24VDC supply, current output, clockwise, 1 pcs M12 5 pin female soket,

INC 210 series, angle, single axis, 0-180° measurement, 15-24VDC m, volt output, counter-clockwise, 1 pcs M12 5 pin female + 1 pcs

INC 210

01: Single axis

PP: 12…24VDC /

15…24VDC

CW: Clockwise

No code : Single Output
Dual : Redundant

output

INC 210 X

XX

XX XX XXX

XX XX XX

A : Angle

360: 0-360°

V: 0-10 VDC

3M : 3m cable

5M : 5m cable

10M : 10m cable
S13F : M12 5 pin female socket
S13M : M12 5 pin male socket
S13FM: M12 5 pin female + M12 5 pin

male socket (redundant models)

value at the order stage.

As standard;
For single output models, 1 pcs M12 5 pin male socket (S13M) is used.
For redundant models, 1 pcs M12 5 pin female + 1 pcs M12 5 pin male socket (S13FM) is used.
However, different socket combinations may be requested as in the examples below.

Please contact us for any other socket model other than M12.

Sample Code 1: INC210-A-01-360-PP-A-CW-S13F

single output

Sample Code 2: INC210-A-01-180-PP-V-CCW-S13FM-DUAL

M12 5 pin male socket, redundant output

KK-INC.006 18.01.19 Rev No:1

4

Manufacturer Firm’s Title, Address Details

Disposal of Packagings: Packaging materials consist of recyclable materials. For providing

recycling, please dispose waste packagings to collecting points of authorized recycling facilities.
Disposal of E-Waste: This device is in conformity with WEEE Directive and consists of recyclable
materials. This product should not be disposed with general waste for preventing negative

effects on enviroment and human health. This product should be disposed to collecting points

of authorized recycling facilities. Further information can be reached from authorized unit.

Address: Tuzla KOSB Organize Sanayi Bolgesi Melek Aras Bulvari, No:67 34956 Tuzla-Istanbul / TURKEY

Address: Tuzla KOSB Organize Sanayi Bolgesi Melek Aras Bulvari, No:67 34956 Tuzla-Istanbul / TURKEY

Manufacturer Firm: ATEK SENSÖR SANAYİ VE TİCARET A.Ş.

TEL: [phone] FAX: [phone]

Web: www.ateksensor.com E-mail: [e-mail]

Authorized Service’s Title, Address Details

Authorized Service: ATEK SENSÖR SANAYİ VE TİCARET A.Ş.

TEL: [phone] FAX: [phone]

E-mail: [e-mail]

KK-INC.006 18.01.19 Rev No:1

DISTRIBUTOR / DISTRIBUIDOR

Atek Sensor Technology A.S.

Tuzla Kimya Sanayicileri Org. San. Bolg. Melek Aras Bulvari, No:67 34956 Tuzla-Istanbul / TURKEY

Brazil and South America / Brasil e América do Sul

Metrolog Controles de Medição

Address / Endereço:

Rua Sete de Setembro, 2656
13560-181 - São Carlos - SP
Brazil / Brasil

Phone / Telefone:

[phone]
[phone]

Internet:

www.metrolog.net
[e-mail]

Tel: [phone] Fax: [phone]

www.ateksensor.com

[e-mail]