Atec T-R-750ADM User Manual

750ADM

mk2

Current Injection

750ADM-H

mk2

Systems

Features

· Primary injection up to 750A

· 2.8V output (750ADM)*

4V output (750ADM-H)*

· 16V 40A output for secondary injection

· True RMS memory ammeter with

single cycle capture

· Multi-function timing system

· Large back-lit liquid crystal display

· Thermal and over-current protection

· Automatic switch-off at end of test

· Compact and portable

· Automatic mains voltage selection*

*See specifications overleaf

T&R Test Equipment is a market leader in the field of current

injection equipment. The range includes secondary injection

units with 100A output capability up to 6000A primary

injection systems. All have true RMS metering, a flexible

timing system, and an easy to understand user interface.

The 750ADM mk2 and 750ADM-H mk2 are compact, rugged

primary current injection systems with a 750A output

capability. The 750ADM has a maximum no load output

voltage of 3.5V and the 750ADM-H has a maximum voltage

of 5V. The units are ideally suited to all low power primary

injection tasks requiring up to 750A for short periods.

Unit type Max. power Max. current

750ADM 2kVA 750A

750ADM-H 3kVA 750A

PCU1-SP+NLU5000 11.5kVA 3kA 5min/5kA 40s

PCU2/E+LU6000 20kVA 6kA

Where higher currents and powers are

required for primary injection, 11kVA and

20kVA primary injection systems are

available. The PCU1-SP and

PCU2/E systems have separate control

and loading units, allowing a wide range

of load conditions to be covered with

different loading units.

PCU1-SP and NLU5000

The units have two outputs, allowing injection of currents as

low as a few hundred milliamps and up to 750A. Voltages up

to 16V are available on the 40A output, allowing higher

impedance trips to be tested. Four true RMS metering

ranges are provided, allowing the full scale of the meter and

trip level to be set independently of the selected output. The

metering has a capture time of less than 20ms, allowing the

rms of a single cycle to be accurately measured. Industry

standard connectors are used on all inputs and outputs for

convenience, reliability and safety.

The 750ADM and 750ADM-H are comprehensively protected

by electronic overcurrent and thermal trips.

The timing system is very flexible without compromising ease

of use, allowing trip times, reset times and reclose times to be

quickly measured to a high degree of accuracy. Two contact

inputs are provided, each of which may be trigged by a volt-

free contact or a dc voltage. The contact inputs auto-sense

for normally open or normally closed contacts.

The 750ADM can be used to test many devices including:

· Circuit breakers

· Primary injection of over-current relays

· Auto-reclosers

· MCB’s

· CT ratio (with external meter for secondary current)

25

750ADM mk2/750ADM-H mk2 Specification

Main Output

The main output on the unit has two taps, allowing the selection

of output voltages up to 16V and output currents up to 750A.

The unit operates at slightly reduced ratings when operating from

a 115V supply.

750ADM 750ADM-H

115V 230V 115V 230V

Open circuit voltage 2.5V 3.5V 3.5V 5.0V

Voltage at 500A 1.9V 2.8V 2.8V 4V

Continuous current 125A 125A 125A 125A

5 min on 250A 250A 250A 250A

1 min on 500A 500A 440A 500A

750A Output 40A Output

Max current 750A 750A 500A 750A

Max current on time 10s 30s 10s 20s

Open circuit voltage 10V 16V 10V 16V

Full load voltage 7.5V 10V 7.5V 10V

Continuous current 10A 10A 10A 10A

1 min on 40A 40A 40A 40A

Metering

The output is metered by a digital true RMS system with a

memory ammeter - whenever the output is switched off, the

current reading is held on the display.

Range Resolution Trip current Accuracy Capture time

20.00A 0.01A 21A ±0.5%rdg+5d 20ms

50.00A 0.01A 53A ±0.5%rdg+5d 20ms

200.0A 0.1A 210A ±0.5%rdg+5d 20ms

750A 1A 788A ±0.5%rdg+2d 20ms

A current trip is automatically set to 105% of full scale of the

selected metering range to protect the device under test.

Timing System

Range 0-999.999s/9999.99s/99999.9s auto-ranging

Resolution 1ms/10ms/100ms

Accuracy ±0.01%rdg+2d (all modes except current operated)
±0.01%rdg+4d (current operated mode)

The contact circuits have an open circuit voltage of 24Vdc and a

short circuit current of 20mA. Each contact circuit will auto-

select for normally open or normally closed contacts. A DC

voltage of 24-240Vdc may also be used to trigger either timer

channel.

The following functions are provided:

Mode Timer Start Timer Stop

Off Timer inactive Timer inactive

Internal start Press ‘ON’ Contact 1

Single contact Contact 1 Contact 1

Dual contact Contact 1 Contact 2

Current operated Current > 20% Current < 20%

of range of range

The output is automatically switched off at the end of the test to

safeguard the relay under test.

Note: Due to the company’s continuous research programme, the information above may change at any time without prior notifica tion. Please check that you have the most recent data on the product.

T&R Test Equipment Ltd, 15-16 Woodbridge Meadows, Guildford, Surrey, GU1 1BJ, UK

Tel: [phone] Fax: [phone] email: [e-mail]

RS232

An RS232 port is provided to allow connection to a PC or a

printer. ADMlog software is available as an optional extra to log

results from the 750ADM and transfer them to a spreadsheet.

T&R Link

The T&R Link allows a T&R DVS3 mk2 voltage source to phase

lock to the 750ADM current.

Supply Requirements

Auto-selecting 750ADM 750ADM-H
115V±10% 50/60Hz 1ph 2000VA max 1900VA max

230V±10% 50/60Hz 1ph 3000VA max 3900VA max

Temperature Range

Storage -20°C to 60°C Operating 0°C to 45°C

Dimensions Weight

380mm x 314mm x 221mm 21.5kg (750ADM) 23.5kg (750ADM-H)

Accessories

Operating manual, mains lead, spare fuse set and carrying strap.

Optional 750ADM-AL Lead Set specifications

A range of output leads are available to complement the

750ADM. The standard 750ADM-AL lead set is 3m long,

recommended for use with a 230V Supply. A 1.5m lead set is

also available, and is recommended when operating from a 115V

supply. The leads consist of double insulated 95mm2 welding

cable terminated in Dinse high current connectors

at the 750ADM end and

high current welding

clamps at the load

end.

Low current timer

leads are also included

with the lead set:

The 3m lead set weighs 9.8kg including high current leads, timer

leads and case.

Protection and Safety

The unit is protected by electronic over current and thermal trips

on the outputs, and circuit breakers on the input and power

circuit. An earth terminal is provided for connection to a local

earth when testing in a substation environment. The unit is

designed to comply with BSEN61010, and is CE

marked.

The standard 750ADM is supplied

in an aluminium case. It is also

optionally available mounted in a

Pelicase with space for leads.

26

www.trtest.com

750ADM mk2 Data sheet rev 0 16/09/09